All Available Parts - 1972 Mercury Cougar

Restored driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weather strip. Shipping...

REQUIRES sending your cores in advance.This is a restored aluminum 3 piece trim set from an early 1971 Mercury Cougar. Included are rear of hood trim Ford part # D1ZZ-16B918-A. Both fender trim pieces Replaces Ford part number D1WY-16C133-A and D1WY-16C132-A. Our restored aluminum trim is correctly bright dipped or anodized like originals.Technically these trim pieces were only used during the first 6 months of production on 1971 Mercury Cougar and all XR7 models including...

Used, passenger side, front lower, aluminum channel section, for installing the roof side or upper door and quarter window weatherstripping. Right and left sides are contoured differently, for the 1971-73 Mercury Cougar and Ford Mustang coupe and convertibles. These channels also have pre-drilled holes for installation, often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core passenger vinyl half roof trim. Call...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core driver vinyl half roof trim. Call 503-463-1130...

Left side factory aluminum door guard.

Used rubber bumper for the tilt column. 70 - 73 tilt columns require 3 bumpers, one on the lower and two on the upper knuckles. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth.  Replaces Ford part # D0AZ-3B661-A. *NOTE*...

New Old Stock Glove box or glove compartment light with switch. Fits 1971-73 Mercury Cougar and Ford Mustang. Used switch and wiring assembly, tested and working. Ford part number D1WY-14413-A. Fits 71 CougarFits 72 CougarFits 73 CougarFits 71 MustangFits 72 MustangFits 73 Mustang ...

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.

This extension holds the inner spring tube in place on the 70 - 73 tilt column. Fragile piece, should take great care when tapping on this pot metal piece. Limited supply. Ford casting number: D0ZA-3790-*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Good used upper collar for the tilt column on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found in 1973 and newer Ford products, mostly F100 and Bronco.  These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: There are other versions of the Nodular iron third members. Non-"N", lazy "N", and square "N" this version. See related items.  Please have your desired date in mind when calling or place it in...

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...