All Available Parts - 1970 Ford Mustang

All new disc brake pads are supplied to us by brand name manufacturers. Boxed sets of four pads.

Each kit contains the seals for one caliper assembly. Replaces Ford Part #: C8ZZ-2B120 and #C8ZZ-2B121 Check out this video

C9OZ-2K004-A Right hand side disc brake shield used starting in 1969. Original Ford part number for RH or passenger side is C9OZ-2K004-A, and the LH or driver side is C9OZ-2K005-A. Starting in 1969 the brake cooling vent was enlarged, these work find on 1968 disc brake spindles. Clean Western part with no heavy corrosion like you see on Eastern cars.

C9OZ-2K005-A Left hand side disc brake shield used staring in 1969. Original Ford part number for LH or driver side is C9OZ-2K005-A and the RH or passenger side is C9OZ-2K004-A. Starting in 1969 the brake cooling vent was enlarged, these work find on 1968 disc brake spindles. Clean Western part with no heavy corrosion like you see on Eastern cars.

This kit is a must when redoing the disc brakes on a 1968-73 Cougar. Includes new brakets (caliper stabilizers), bolts, pins, and clips and rubber dust seals. Kit includes the pair. Check out this video

Excellent quality replacements. Includes hub, studs, and bearing races. Single piece design. 2" spacing from hub to rotor face

Quality rebuilt RH disc brake caliper for 1968-1973 Cougar / Mustang and lots of other Ford products. WCCC also offers "Core" calipers for those that wish to rebuild their own or send them to a rebuilder that requires core calipers.  Hardware not included. Check out this video

Quality rebuilt LH disc brake caliper for 1968-1973 Cougar / Mustang and lots of other Ford products. WCCC also offers "Core" calipers for those that wish to rebuild their own or send them to a rebuilder that requires core calipers. Hardware not included. Check out this video

Wheel seal for both front disc and front drums, 1967-73 Mercury Cougar and 1967-73 Ford Mustang with V-8. Seals sold individually. Two of these are needed, one for each side on the front.

Bleeder screw for your 1968 - 1973 Cougar or Mustang Calipers.

Reproduction driver side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

Reproduction passenger side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

All new premium disc brake pads are supplied to us by brand name manufacturers. Set of 4 pads. Low dustProtective underlayerRubber/steel/rubber layered shimScorched

OEM FoMoCo cast core grade RH disc brake caliper for 1968-1973 Cougar / Mustang and lots of other Ford products. For those that wish to purchase assembly line style calipers for rebuilding. Pucks should be inspected and or replaced, seals replaced, and what ever machining should also be done. No Core or deposit required.  Hardware not included. Check out this video

OEM FoMoCo cast core grade LH disc brake caliper for 1968-1973 Cougar / Mustang and lots of other Ford products. For those that wish to purchase assembly line style calipers for rebuilding. Pucks should be inspected and or replaced, seals replaced, and what ever machining should also be done. No Core or deposit required. Hardware not included. Check out this video ...

Please note, this is a Mustang brake hose and the fittings are different for the Cougar. Flexible high pressure replacement brake hose for the rear drum brakes on Ford Mustang and attaches to the rear end housing. Replaces Ford part number D0ZZ-2282-A. *NOTE* If you have ordered a reproduction Cougar brake line from the front of the vehicle to the rear axle, you will want to make sure which fitting you have. Many of the reproduction Cougar brakes lines come with the incorrect mustang fitting....

Reproduction brake pedal hanger also known as brake pedal support for Mercury Cougar and Ford Mustang.

Bushing that goes to the inside of the brake booster pushrod. This is the early version of this part that is made of plastic, a later version was introduced in 1969 which was made of nylon and is/was more durable.Replaces Ford Part number C9AZ-2474-A

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

Replacement brake pedal pad trim for the Mercury Cougar or Ford Mustang equipped with a manual transmission. Replaces Ford part # D1ZZ-2A487-B.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Longer arm than drum brake pedals. Works only with 1970 power brake booster rod. Pedal shipped bare, picture may show hardware and pedal pad with trim. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you...

D0ZZ-6501508-B This is the correct hanger for a 1970 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D0ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily. *NOTE* This item can only be shipped via UPS ground. No Foreign orders please. Check out this video ...

New high temperature enamel for painting your block and underhood parts. This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel.

This charcoal black aerosol paint is a very close match to the original finish used on 1967-68 Cougar XR-7 lower dash structures and steering columns. We've tried it ourselves and have been satisfied with the results. Our only critique is that it's a bit slower to dry than other paints we're used to. The AccuMatch(TM) Interior Paints are the result of years of work and perfectly match the original color shades. Each color has been expertly color-matched. Paints feature extra-high pigment...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

VHT epoxy paint is great for a number of applications. It's a unique one step protective coating that dries quickly and doesn't require a primer. It provides excellent rust, corrosion and chemical resistance which, needless to say, is ideal for anything you're doing under your hood or under and around the body of your car. One can covers about 12 - 14 square feet.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

Used rear defog blower motor with integral fan. Ford supplied these for many years, some have different connectors on them. Some have the square style as found starting in 1973. We have a good supply of working and tested motors, so request the type of plug end you need.Replaces Ford part number C8AZ-18527-A and D3AZ-18527-A.

New Old Stock 'DEFOG' knob. Attaches to hand down defog switch on 1969-70 Mercury Cougar and Ford Mustang with rear defogger option. *Note - Excludes 1970 Mercury Cougar XR7. Those cars had the defog switch in the courtesy light panel. Replaces Ford part number C9WY-18519-A.

Used timing chain cover for any 351C or Cleveland engine from 1970-74. Mercury Cougar and Ford Mustang and additionally fits 351M / 400M engines. All steel construction without excessive rust or damage. Installation bolt kits also avialable.Replaces Ford part number D0AZ-6B070-A.*Note - will not fit 351W or Windsor engines.

Used timing chain cover for any 390 or 428CJ engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968-70 Ford with 390 or 428 cubic inch engines. Cast aluminum construction without excessive damage. Installation bolt kits also avialable. Ford casting number C8AE-6059-B. *Note - Is not technically compatible with 1967 or earlier 390 engines.

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a brass plunger. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to retain your mounting bracket...

This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength.  Replaces Ford part # C8ZZ-19A566.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

Original two piece assembly that bolts to the passenger side of your firewall on AC equipped Cougar's. Comes as taken from parts car. If you own a 1969 Cougar you will need to look at the configuration of the evaporator lines. During the 1969 model year this grommet bracket changed to reflect the running year change. Ford part # C9ZA-19B588-C.

Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. This part will not have any missing "chunks" but will show hairline cracks most evident where the heater core tubes pass through. Taken from a 1970 Cougar. Ford Part #: C9ZA-19B588-C. * Note - Used starting during the later part of 1969. Compare the evaporator line orientation for both years.

Used OEM Ford heater blower motor resistor for cars with factory installed air conditioning, it attaches to the A/C blower fiberglass housing. Fits all 1969-73 Mercury Cougar and Ford Mustang with integral or factory air conditioning. The reproduction resistor that fits the 1967 - 1968 Cougar and 1965-1968 Mustang has a different hole pattern. According to manufacturer information (INDAK), the OHM output for this switch makes it incompatible with the earlier reproduction resistor. We inspect...

New heater blower motor resistor that attaches to the heater blower fiberglass housing. Ford part # C8OZ-18591-A.1970 and Later Maverick and Comet1971 and Later Lincoln

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Ford part # C9ZZ-19858-C.

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1969-70 variety, which have specific colored wires and leads....

Used air conditioning evaporator core, for most of the 1969 model year and all of 1970. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have...

This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.

This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.You can find the retainer clips here, 2 required.Find the washer here, 1 required. ...

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

Heater door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater door allows air to pass over the heater core in the A/C box. This is the smallest door in the A/C box, and the one subject to the most damage from moisture. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

Shaft or rod for air inlet damper door for any 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-A.

Shaft or rod for the evaporator damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Usually ships in 3-5 business days. Reproduction heater box with A/C for 69 - 70 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). This assembly comes with two heater core gaskets, one for early 69 and one for late 69 - 70. NOTE: We've received some helpful...

Air conditioning fan blower assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine from 1969-73. Original condensation drain hose from the A/C case, through the floor board, to the ground. Replaces Ford part # C9ZZ-19858-C.

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1967-68 brackets, but this one has a slightly longer stud. Replaces Ford part number C9ZZ-18A456-A.

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Shaft or rod for the A/C damper blower door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1969-73 shaft is clocked differently than the 1967-68 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. 

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...

Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...

Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...

Used extension or rod for the vacuum actuator for controlling the Heat / Defrost door on the 1969-70 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 1-3/4 inches long. For 1969-70 Cougar and Mustang. On the passenger side of the blower housing assembly. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18A3...

Used extension or rod for the vacuum actuator for controlling the A/C heat door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 1-13/16 inches long. For 1969-73 Cougar and Mustang. On the driver side of the blower assembly. Vacuum actuator sold separately, see related items. This is an unstamped tab, and is plain steel color. Ford part...

Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.

This correctly formed heater tube for the 351C attaches to the intake manifold on the passenger side of the carburetor and has heater hoses connecting to either end. A darn near impossible part to find in used form as they are always rusted out and nasty. This is a one year only part that you will not find anywhere else!Length: 13 9/16"Replaces part # D0ZZ-18696-A.

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970. After 2/1/1970, the stripe on the hose was changed to yellow. This hose features durable red striping with "Autolite" spelled out and is dated H9H04B. Correct for all V-8 engines WITHOUT air conditioning. The hoses for cars with A/C have 90 degree elbows molded at one end which fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970. A red stripe was used before 2/1/1970. Durable yellow striping with "Autolite" spelled out and dated H0A13A. Correct for all V-8 engines WITHOUT air conditioning. Hoses for cars with A/C have a 90 degree elbow molded into one end that goes on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows! ...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970 WITH factory or integral air conditioning. Before 2/1/1970 a red stripe was used. Durable yellow striping with Autolite spelled out and dated HOA13A. Correct for all V-8 engines with A/C. These hoses have the correctly molded 90 degree elbow that goes on the water valve side. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the yellow striping shows! ...

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970 WITH factory or integral air conditioning. After 2/1/1970, the red stripe and date code was changed to yellow. Durable red striping with "Autolite" spelled out and dated H0A12A. Correct for all V-8 engines with A/C. Theses hoses have a correctly molded 90 degree elbow on one end that attaches on the water valve side. Some length trimming may be required for a tight looking fit. Turn those...

Used heater tube for the 351C attaches to the intake manifold on the passenger side of the carburetor and has heater hoses connecting to either end. Darn near impossible part to find in used form as they are always rusted out and nasty. One year only part.Ford part # D0ZZ-18696-A.

This correctly formed heater tube for the G code 1970 Boss 302 engines, attaches to the intake manifold on the passenger side of the carburetor. A darn near impossible part to find in used form as they are always rusted out and nasty. This is a one year only part that you will not find anywhere else!Replaces part # D0ZZ-18696

This correctly formed carburetor throttle solenoid idle bracket for the 1970 428CJ engines on any Mercury Cougar or Ford Mustang. This is a nice reproduction item.Replaces part # D0ZZ-9B550-A.

These are reproduction heater hose grommets for the heater hose to pass through the firewall. Most of the firewalls that we have seen have a flared opening for the hose without a grommet. These are a more dense rubber than our other versions. Still not sure that they are needed?

Our heater cores are the finest available anywhere for any price and they are constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part. Replaces Ford Part #: C9ZZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Reproduction heater duct nylon rivet #375064-S is sold individually.

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Basic clam shell box as shown for cars WITHOUT AC. Keep in mind we have nice original FoMoCo units for less money! *NOTE*Kit does not contain heater blower motor, squirrel cage, or blower motor mounting plate. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1969-73 Cougars and Mustangs, but also on 1968 and newer Fairlanes, Torinos, Rancheros, Cyclones, and Montegos. Also installed on 1970 and newer Mavericks / Comets, plus 1971 and newer Lincolns.Ford part # C8OZ-18591-A.*Note - Excludes Heater with...

Used heater blower motor for 69 - 70 Mercury Cougar and Ford Mustang. The reproduction off-shore motors may or may not prove to be as good of value as these good used original FoMoCo motors. To date, all we can find for these cars are foreign made units. Keep in mind our used motors carry a one year warranty and the new motors have a 30 day warranty. Also know that the mounting plate is included for free just for the asking on these used motors. We personally have never used the reproduction...

Used mounting plate for the heater blower motor on the 69 - 70 Cougar or Mustang without A/C.Keep in mind that this same plate can be used on a 67 - 68 Cougar and Mustang heater blower motor with A/C.

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...

1970 Mercury Cougar and Ford Mustang convertible clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. *NOTE* Vertical chrome trim not included. Air conditioning cars were supposed...

Good used bracket with all three plastic guides in perfect condition. This bracket is correct for Coupe and Convertible. Engineering # D0ZB-6529944-A. Here is the 3M product used to glue the glass to the bracket. This is found on late 1970 cars, it uses a spring clip for holding the quarter window regulator. We have found an "E" clip to use as a service replacement. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or...