All Available Parts - 1967 Ford Mustang

Also called a pumpkin, 3.00:1 locking ratio.Check your door tag under "Axle".Please note, that this is a vintage, two pin equa lock third member. Most of us should be looking at a modern design traction lock for spirited driving. The 1960's Equa-Lock, is pretty weak.1967 code A 1968 code E

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1967 late 9 inch rear end housings without fill plug in the steel...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange without fill plug in housing. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Complete rear end housing - drum to drum, with...

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *Note - This bracket is a bit longer than the 2V version.

"L" shaped bracket that mounts to the rear of the Holley carburetor mounting hole for attaching the return spring. Bracket faces forward when installed.

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *NOTE* This bracket is a bit shorter than the 4V version.

NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.

Neat detail item, stamped steel with zinc plating. Mounts on intake manifold and holds one end of the accelerator linkage spring for the 289 / 302.

This is a core five piece set of front windshield mouldings for a 1967 - 1968 Mercury Cougar and Mustang (except fastback). These mouldings need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard mouldings of that description. We do not recommend the reproduction, "offshore"...

Driver side vertical windshield moulding. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part number C5ZZ-6503137-B.

Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.

Core lower windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503148-B.

Core passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503136-B.

Core passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503144-B.

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually. You can find the reproductions here.Ford Part number C7ZZ-6510182-A

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B

NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.

Identified with the straight bracket compared to the 1968 relay which has a bend. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. Ford packaging reads C7ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Helpful tip:  For those having trouble getting their tilt away mechanism to...

Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video, showing how to replace the pin Check out this video...

We think that this jumper or adapter wiring lead, was used in 1967 when the Neutral safety switch changed from two separate plugs to a single square 4 combination plug. There could have been an overlap where the plug from the firewall to the 14401 main under dash harness changed to the single square 4 combination plug. We have also observed the two separate neutral safety switch plugs plugged directly into the updated square 4 plug. 

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate. Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. NOTE * Grade B bell housing will have a chip or heavy scarring on the bottom, see photo...

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

This connects the vacuum release valve to the vacuum system*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This plate attaches the 3/8" steel fuel line under the driver's side rear torque box, as it makes its way from the rear frame rail out to the rocker area. It acts both as a mount and as a protector from road debris. These were used on late 1967 to 1968 Cougars and Mustang with the 3/8" fuel line. Early 1967 cars had smaller 5/16" fuel line, and different routing (through the transmission tunnel), and did not use this part. Mounting bolts included.

Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 3 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Bob Mannel's book indicates that this vacuum fitting was for A/C and Thermactor smog. Replaces generic Ford vacuum fitting part number 9A474.

Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.

Hot idle compensator valve assembly for many Ford engines with PCV, starting in 1964 through early 1968. Typically found on 1964-66 Ford 260-2V, and 289-2 engines with air conditioning. 1967-68 289-2V, 302-2V and some 390 engines all with air conditioning and PCV or closed emissions. The Ford assembly manual indicates that the Hot Idle Compensator Valve 'T' Assembly, was installed by removing 3/4 inches of the PCV hose, 2-1/4 inches (on center of the PCV valve). See picture for clarification....

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

Replaces Ford part #C7AZ-6892. For round hole with two notches, aluminum or steel valve covers.

NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A

C7ZZ-6A664-B Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the 390 PCV transfer tube on the intake manifold. Molded hose with 5/8" valve end and 1/2" tube end. All 1967-68 S code 390GT or 390-4V engines and 1968-69 428CJ and 428SCJ engines, includes Cougar, Mustang, Fairlane, Torino, Ranchero, Cyclone, and Comet. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

This adapter is threaded on bottom for Boss 302 / 390-4V / 428CJ PCV valve and 6 degree nipple on side. Gold Cadmium plated, not painted originally. This only works with the OEM or reproduction threaded PCV valves.Replaces Ford Part Number C7OZ-6A706-A.

This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.

Driver quality used left side or driver side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Good used original handle with no obvious pitting or blemishes. This handle was not used on the XR7. Found on 1967 standard model Cougar and 1967 base model Mustang. Ford casting number C7OB-6222614-A.*Note - 1967 Mustang with deluxe interior, i.e. brushed door panels, used a similar handle, but with Ford part number C7ZB....

This is the assembly that your inside door handle attaches to and features all new components. They are gold cadmium plated to resist rust and corrosion. *NOTE* We have had complaints of these not fitting as well as originals therefore we suggest buying our used units. Rod retainers not included. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that is very hard to find in rust free condition with a working vacuum check valve. Beware of substitutes as there are close facsimiles with different sized nipples, different brackets or plastic built in check valves. These versions off later model cars...

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Very clean rust free support with no rust or collision damage. It will come with the lower support but we cannot always provide a perfect one. If this is critical please call so we can check inventory before you order.

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

One required per car, mates to female version attached to the under dash loom. Same plug for tilt and non tilting columns.

Used plastic bushing for the lock pawl rod guide for the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. These delicate little bushings are needed to keep the lock pawl rod in alignment with the vacuum motor shaft. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the driver side of all 1967-68 Mercury Cougar and Ford Mustang. It is also used on the passenger side if you have air conditioning. This is the short style bracket. There is also a long style for both the passenger side courtesy light if you don't have factory air conditioning. If you have factory air conditioning you would want the short bracket that doesn't come into...

Two piece pre-bent OE steel brake line kit that runs down the rear axle on the 8 inch rear end of a 1967, 1968 or 1969 Mercury Cougar or Ford Mustang.The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found in 1973 and newer Ford products, mostly F100 and Bronco.  These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: There are other versions of the Nodular iron third members. Non-"N", lazy "N", and square "N" this version. See related items.  Please have your desired date in mind when calling or place it in...

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...