Rubber & Seals

This hard plastic part slips over your floor shifter stem and keeps coins and such from falling inside your center console. Replaces Ford part number C7ZZ-7C445-A. Check out this video

This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

This Steering Box Cover Gasket Reproduction fits the 67, 68, 69, and 70. Replaces Ford part #: C3DZ-3581. If your original steering box is one of the few that is still tight then you will want to open it up, clean out all the decades old solidified grease and put new grease in.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

Reproduction trunk wheel house seam cover for the Ford Mustang. I have actually never seen an original pair of these on a car, but they do serve a purpose if you are in the habit of cramming your trunk full of items you do not want scratched. These attach to the protruding seam where the inner and outer wheelhouse bond together and measure about 14" in length. You will have to modify these to fit your Cougar. Only sold in black. Replaces Ford part # C5ZZ-6531466-A.

Sold as a pair, includes plastic fasteners. There are multiple manufacturers of this particular item and we feel after using them all on our own cars that we carry the best out there. Replaces Ford part #C7ZZ-6520530-A.

Excellent fit whether you are installing OEM thickness glass or repro which often is a slightly thinner gauge, must have when replacing either headliner or windshield. There have been multiple manufacturers of this seal over the years, this is the best fit in our opinion. Fits years 67 - 68 for Cougar and 65-68 on the Mustang. We also sell the bedding compound for the installation.  Replaces Ford part # C6ZZ-6503110-A. Keep in mind this is not a difficult do-it-yourself project, here's...

These vertical seals attach to the leading edge of the rear quarter windows and seal against the rear edge of the door glass. Sold as a pair.Replaces Ford Part #: C5ZZ-6530146 and C5ZZ-6530147. These are the budget or economy versions. We also sell concours versions.

These vertical seals attach to the leading edge of the rear quarter windows and seal against the rear edge of the door glass. Sold as a pair.Replaces Ford Part #: C5ZZ-6530146 and C5ZZ-6530147. These are the premium or concours versions. We also sell economy versions.

This Wiper Pivot To Cowl Seal Reproduction is sold as a pair. Fits both the 67 and 68. Replaces Ford part #: C5ZZ-17475.

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

This listing is for the outer doors pieces only, Cougar and Mustang are identical. These original NOS FoMoCo parts fit better and will last longer than repro.Ford part numbers C7ZZ-6521453-A  and  C7ZZ-6521452-A

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Good fit, includes all hardware shown. We've found that when using our reproduction drop down bracket (for those with headers), the bushings in this kit will rip and tear through the oversized hole, so you can also purchase the pair of the premium polyurethane bushings and the issue will go away. Otherwise you can go with our premium version boot kit of you need internal parts for the cylinder. Replaces Ford Part #: C6OZ-3C651-A ...

New old stock power steering ram cylinder boot and bushings. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C6OZ-3C651-A.

New hex head screw for attaching the fuel filler neck to the rear body. 67 to 70 Mercury Cougar and 1965-70 Ford Mustang. 1965-68 filler necks require 4 of this style screws. 1969-70 filler necks require a total of 5 hex head screws. #10 x 3/8". Replaces Ford number 42120-S8.

Reproduction door to window seal for the early 1967 Mercury Cougar and Ford Mustang. These are copies of ones for use before 12/14/1966. Install at the rear of the door at the edge of the door window. Replaces Ford part #: C7ZZ-6520558-B and C7ZZ-6520559-A. Sold as a pair. This part is often listed incorrectly under C7ZZ-6520588.

NOS lower inside door seal for any 1967-68 Mercury Cougar or Ford Mustang. No wrapper, this is not a reproduced item. Not very many Cougars or Mustangs came with this seal, we think it may have been for wind noise? Unknown. These are pre-drilled for mounting, no hardware included.Replaces Ford part number C7WY-6520272-A.

It is not often we get perfect used rubber, but nothing fits like OEM!The Engineering number on the bottom of the driver side reads C7ZB-6521449-ACheck out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

It is not often we get perfect used but nothing fits like OEM!The Engineering number on the bottom of the passenger side reads C7ZB-6521448-ACheck out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

These are a higher quality rubber than the other reproduction available. Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183

New and improved reproduction bottom of the door seal for the 1967 - 1970 Mercury Cougar or Ford Mustang. Unlike previous versions, these are now made with denser material and are much more rigid. They measure 38" for 1967 -1968 and 41" for 1969-70 so you will have to trim them down if you have a 1967-68. One of the most common missing parts on a 1967-70 Mustang or Cougar today is the lower weatherstrip seals on the doors. These seals were added to cars to keep dirt and moisture from entering...

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

Original NOS part, new in box. Ford part # C5ZZ-6503110-A