Engine & Under Hood

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and C-6 (automatic code U) transmission. This supplier with the Ford number stamped on the side strap is typically from Dearborn assembled cars. Used core radiator for recoring and restoration. This listing currently has an older replacement 4 tube core. The lower tank has minor damage to the area of the pet cock as shown. Typical Dearborn installed assembly line radiator.Replaces...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and manual transmission. Used core radiator for recoring and restoration. This listing currently has a lower tank with minor damage to the area of the hose outlet as shown. Typical Dearborn installed assembly line radiator.Replaces Ford part number C7ZE-8005

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

New old stock Zinc radiator cap. Motorcraft stamped, with RS 12A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9AZ-8100-A.

These are O.E.M. replacements and will not fit most after market radiators.

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

Reproduction aluminum crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Originals were made from steel.

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part. Check out this video

Temperature thermostat for use in very early 1967 cars with 390 engines.  2-1/2 inches in diameter, 195°degree opening like OEM Ford. This is a Stant brand of thermostat. Note, this is a larger diameter thermostat than the common one used on a small block and most Ford engines. Only used with the intake and thermostat housing with large size diameter of 2-1/2 inches.

Used aluminum water neck of thermostat housing for EARLY 1967 Mercury Cougar or most other 1965-66 Fords with 390 / 428 engines. Cast aluminum finish. For use with early style 2-1/2 inch thermostats. Correct for early 1967 FE engines before about 11/1/1966. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. No thermal switch provision. Ford part with the C5AE-8594-A casting number.  *Note - mid and late 1967 cars used the...

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 3 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Bob Mannel's book indicates that this vacuum fitting was for A/C and Thermactor smog. Replaces generic Ford vacuum fitting part number 9A474.

C6ZZ-6582-H Smooth chromed valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 DGS Mercury Cougar and optional on 1965-67 Ford Mustang with 289 engines. Ford master parts catalog shows a right and left version of this cover those numbers are C6ZZ-6582-H & C6ZZ-6582-J. *Note - This is a used chrome valve cover. The plating was pretty low quality back in 1966-67 and these will show rust pitting. For best results we recommend the painted version of this valve cover...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C6OE-A. Found on many Ford 289 engines from 1966-67. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other casting...

Dated 6M29, December 29, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two...

Dated 7C17, March 19, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Dated 7C20, March 20, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Dated 9M6, December 6 1969. Boss 302 or 351C Ford water pump core, suitable for rebuilding. This version has a casting number of D0OE-D. Found on many Ford 351 Cleveland engines from 1970. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers....

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...