Heater with Air Conditioning & Air Conditioning Components

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a grade "A" unit with no issues other than some discoloration.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1969-73 door, but without a small notch. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

This A/C evaporator drain hose is molded flex hose similar to the original, but it will need to be cut to the proper length. It is correct for 67 - 68 but can be made to work on 69 - 73. Replaces Ford part #: C7ZZ-19858-C or C8TZ-19858-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "B" part and will have one defect. This part will have a crack, chip missing, etc. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade A hose that is not cracked, may have a small cosmetic scuff in the foam, and the clips will not be broken. Two required per car, sold individually. We also have a listing for Grade B condition, that will have a minor issue or two. Ford part #: C7WY-19B680 or B5A-18556-C.

This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade B hose that may have a crack or tear, or with a broken clip. Two required per car, sold individually. We also have a listing for Grade A hoses. Ford part #: C7WY-19B680 or B5A-18556-C.

New A/C vent hose with cam locks for your Mercury Cougar or Ford Mustang equipped with factory A/C. This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Two required per car, sold as a pair.Ford part #: C7WY-19B680 or B5A-18556-C.

High Quality cloth wrapped heater duct hose. This is the correct length for most cars, but will need to be cut for proper fit in some applications. Hose diameter: 2 1/2"

This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.You can find the retainer clips here, 2 required.Find the washer here, 1 required. ...

This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.

Used passenger side air conditioning duct for any 1971-73 Mercury Cougar or Ford Mustang with factory or integral A/C. Connects the center manifold to the passenger side elbow or connector.Replaces Ford part number D1ZZ-19B680-A or D1ZA-19C735-AB.

Used center vent connector or duct tube. Fits 1969-70 Mercury Cougar with factory or integral air conditioning. This attaches to the center register in the dash pad. Replaces Ford part number C9WA-19B737-A or C, and C9WY-19B680-B.*Note - Will not fit Ford Mustang.

Used driver side connector duct tube or elbow, attaches to driver side air conditioning register. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19B680-D and C9ZA-19C850-A.

Used passenger side connector duct tube or elbow, attaches to passenger side air conditioning register. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19C692-B and C9ZA-19C626-C

Used driver side connector duct tube, attaches to driver side air conditioning register. Fits center assembly. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZA-19B923-B, C9ZA-19B923-A, or C9ZZ-19B680-C.

Used passengerer side connector duct tube, attaches to passenger side air conditioning register. Fits to center assembly. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZA-19B737-C or C9ZZ-19B680-B.

Used driver side flex connector duct tube, middle of three duct tubes on driver side. This tube has a stapled flex hose included. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19C692-B and C9ZA-19C615-F.

Steel elbow that uses the A/C coupler from the liquid or sight glass hose to the dryer. This is an OEM Ford part that was originally part of an assembly, which included the sight glass hose, coupler, and this elbow. This elbow has the flared fitting common to the 1967-68 A/C connections. We recommend replacing "O" rings prior to installation, which are commercially available from air conditioning service centers.

Used rubber elbow that vents air to the blower motor on most 1967 Mercury Cougar and Ford Mustangs with factory air conditioning. At some point in time, this elbow design changed. Easy to tell, this early style connects to a nipple on the fan blower motor. The later version has a hole in the motor case. Not needed with new production fan motors, they don't even have the hole. Replaces Ford part number C7ZA-19A786-B.

Used rubber elbow that vents air to the blower motor on most 1967 Mercury Cougar and Ford Mustangs with factory air conditioning. At some point in time, this elbow design changed. Easy to tell, this early style connects to a nipple on the fan blower motor. The later version has a hole in the motor case. Not needed with reproduction fan motors, they don't even have the hole. Replaces Ford part number C7ZA-19A786-A.

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B

These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S

Reproduction water inlet elbow for your 1968 big block Cougar or Mustang.Replaces Ford Part #: C8AZ-18599-AClick on images to enlarge. ...

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

New 1-1/4 inch expansion plug. Expansion plugs were used as dust covers on the wide bearing style air conditioning pulleys commonly used on Ford cars 1965-68. These are not a real tight fit in those pulleys. Best to still install to keep dust out, we recommend using a bit of JB Weld to hold them.

Senses temperature to open and close the expansion chamber and made just like the original.Will work with both R12 and R134 systems.Replaces part #: C7ZZ-19849.

For factory installed A/C on Mercury Cougars and Ford Mustangs. This unit functions great, but when compared to the NOS unit, you will see that it is cosmetically a little bit different. This uses the "O" ring style seals which are not included.Will work with both R12 and R134 systems.

Expansion valve for factory air conditioning for the Mercury Cougar or Ford Mustang.Will work with both R12 and R134 systems.Replaces part #: D1ZZ-19849.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. We also offer another valve that was used for a period of time see the related evaporator valve.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service. This valve was originally stickered with a FoMoCo tag and...

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. This is the uncommon version, we have a limited supply of these from original cars.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C6OZ-19849-A. aka YG-24

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original! Several known versions of this valve at least two shown in photos.Fits 1969-70 Mercury Cougar and Mustang, 1968-69 Lincoln Continental.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C8VY-19849-A. aka YG-28

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1971-73 Mercury Cougar and Mustang. It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # D1OA-19849-AA. aka YG-27

New clear plastic lens or face plate for the A/C and heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

New clear plastic lens or face plate for the air conditioning control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to...

New clear plastic lens or face plate for the air conditioning control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

Rubber plugs for sealing the holes in the firewall of any 1967-68 Mercury Cougar or Ford Mustang. These plug the firewall holes if you don't have air conditioning or if you have deleted your heater core. Fits 1" body panel holes for all years.Sold as a pair.Original Ford part 377678-S2

Used fresh air vent found in the passenger side kick panel of all 1969-70 Mercury Cougar and Ford Mustang with or without air conditioning. Please also see the listing for new gaskets for installation.Replaces Ford part number C9ZZ-6501934-A.

Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

Correct for Mercury Cougars and Ford Mustangs with air conditioning. This is a lower profile design to clear your factory installed in-dash A/C system. Replaces Ford part number C9ZB-6506010.Reference from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for...

Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. This part will not have any missing "chunks" but will show hairline cracks most evident where the heater core tubes pass through. The engineering number imprinted on the back side of this grommet taken from a 1967 Cougar is C7ZA-19B588-A. Good through mid year 1969. Compare to the 1970 item pictured for selection on your late 1969 Cougar.Please indicate in the Order Notes...