All Available Parts - 1967 Mercury Cougar

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing bolts is so equipped.

This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a slightly larger round punch to open the hole slightly. If the boot isn't seated low enough, the boot will tear and fail in short order.

Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.

Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Replaces Ford part #: C6OZ-3020-A.

C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Reproduction rubber dust seal or boot with steel reinforcing ring for front suspension inner and outer tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. This is the concours version with Ford casting number C6OA-3332-A.*Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #...

It took a long time but our supplier finally got this bushing right. They ended up copying a never installed production original bushing Ed Meyer acquired from the Kar Kraft factory back in the day. All details have been copied including the two small ribbed lines located on one side. NOS Bushing notes: If you have NOS C9ZZ-5493-A front sway bar bushings in a Ford bag good luck making them fit. Yes, its a documented fact that almost all NOS 15/16" sway bar bushing Ford sold in a bag are too...

Standard size front sway bar bushings were 3/4 inch from 1967 - 1970. Rubber construction, sold in pairs only. Replaces Ford Part #: C7OZ-5493-C or C6OZ-5493-B.

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-E

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-J.

Used front sway bar, does not include any mounting brackets or end link kits. Ford part # C7WY-5482-A.

This used under dash wiring harness repair pigtail is from the tachometer, turn signal switch, ignition switch, and back-up lamp switch to the driver side (left hand) door pillar. This is part of the 14401 main under dash wiring harness.*NOTE* This pigtail also has a pink resistor wire that should not be cut or spliced because it's ohm resistance is dependent upon it's length.**NOTE** Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on...

Used fuse block / box with wiring pigtail for the under dash harness for your Mercury Cougar Standard and XR7. This fuse block has a pigtail where the individual fuse holders and wires can be removed. This is also part of the 14401 main under dash wiring harness.Ford part # C6OZ-14A068-A.

Used under dash wiring harness repair plug and pigtail to the turn signal relay for your Mercury Cougar. This is part of the 14401 main under dash wiring harness. Early version is identified by the double purple wire on the end, later 1967 versions have only one purple wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Used under dash wiring harness repair plug and pigtail for your Mercury Cougar Standard and XR7. This plug and pigtail is a lead to the k8/9 relay and is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the driver side (left hand) map switch on the dash of your Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail for the seat belt relay on your Mercury Cougar Standard. Good for Standard and XR7 models.

Used under dash harness plug and pigtail to repair the passenger side (right hand) leads to the fuel sender / K-8/9 relay for your Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the wiper coordination switch (foot pump/washer) for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.*NOTE* The individual wires can be removed and the block is also available without the wiring pigtail.

Used repair plug and pigtail goes from the under dash harness thru the firewall to the heater motor on non A/C Mercury Cougars. This harness repair pigtail comes with the thru firewall rubber grommet and is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair ignition switch plug and pigtail for your Mercury Cougar Standard. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail for the turn signal indicator relay on your Mercury Cougar. This is part of the 14401 main under dash wiring harness.**NOTE** Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information...

Used under dash wiring harness repair plug and pigtail to the turn signal switch for the Mercury Cougar. This unit comes with an in-line fuse cartridge, the wires can be removed, and the bare plug can also be purchased separately. This is part of the 14401 main under dash wiring harness. We also have the mate to this harness, the turn signal to under dash pigtail.*NOTE* The wires on the plug can be removed. The bare individual plug can also be purchased separately.**NOTE** Need help diagnosing...

Used under dash wiring harness repair plug and pigtail that goes to the blower motor fan switch for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the dimmer switch for the Mercury Cougar. The individual wires and the bare plug can be purchased separately and are part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair pigtail and ring connector to the ignition switch for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail lead to the cigar / cigarette lighter for the Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness.

Used under dash harness repair plug and pigtail lead for the parking / headlights and brake warning switch for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used ground wire repair pigtail and eyelet for the under dash wiring harness for the 1967 Mercury Cougar Standard. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harenss repair plug and pigtail to the wiper motor for the Mercury Cougar. This is part of the 14401 main under dash wiring harness. We also carry the mate for this pigtail. You can check wire colors for correct pigtail.

Used under dash wiring harness repair plug and pigtail to the low fuel relay for the Mercury Cougar XR7 or Standard model with the Safety and Convenience option. This is part of the 14401 main under dash wiring harness,

Used under dash wiring harness repair plug and pigtail for the parking brake warning light in the overhead for the Mercury Cougar XR7. This unit connects at the passenger side door jamb to the overhead harness. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail lead to the oil pressure gauge and oil pressure gauge lights for the Mercury Cougar XR7. The individual leads can also be purchased separately. This is part of the 14401 main under dash wiring harness.Check out this video of our Gauge Tester

Used under dash wiring harness repair plug and pigtail to the passenger side (right hand) dash mounted map light switch on the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail leads to the map light switches to the overhead wiring harness at the passenger side (right hand) door jamb for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the "C" pillar courtesy light switch mounted on the dash for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.Fits:1967 Mercury Cougar XR71968 Mercury Cougar XR7

Used under dash wiring harness repair plug and pigtail to the emergency brake warning relay for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar. The individual wires can be removed and the bare plug can also be purchased separately. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the instrument panel on the Mercury Cougar Standard. The wires can be removed and the bare plug can be purchased separately. This is part of the 14401 main under dash wiring harness. 

Used under dash wiring harness repair plug and pigtail to the instrument panel for the Mercury Cougar XR7. The Standard and XR7 used this exact same plug with the only difference being the wire configuration. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail from the low fuel relay to the passenger side (right hand) door jamb for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail leads to the 6amp circuit breaker for the headlight door solenoid for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the glove box light for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the heater resistor for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail for the neutral safety switch / back-up lights and engine feed harness for the LATE 1967 Mercury Cougar. Works for both standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The blue/red to yellow/black wire is for the radio feed. The only difference between the early and late harnesses, is the early harness has an extra blue wire.

Used under dash wiring harness repair plug and pigtail for the door ajar / seat belt warning for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail for the console lights. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the low fuel sending unit for the Mercury Cougar XR7 or Standard model with the Safety and Convenience option. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the low fuel sending unit / K8/9 relay for the Mercury Cougar XR7 or Standard model with the Safety and Convenience option. This is part of the 14401 main under dash wiring harness.

Used under dash harness repair plug and pigtail lead to the low fuel sending unit for the Mercury Cougar XR7 or Standard model with the Safety and Convenience option. This is part of the rear wiring harness, plug is at the passenger side kick panel. 

Used under dash wiring harness repair plug and pigtail to the ignition switch for the Mercury Cougar. The wires can be removed and the bare plug can be purchased separately. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the footwell courtesy light switch on the dash of the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash harness repair plug and pigtail to the heater resistor for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair plug and pigtail to the dash mounted courtesy light on the Mercury Cougar. The socket is the same on both sides. This is part of the 14401 main under dash wiring harness.

Used taillight wiring harness repair eyelet and pigtail that is the ground wire at the fuel filler for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness.Good for both STD and XR7 models.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

Used taillight wiring harness repair plug and pigtail that connects to the 14405 mid-harness assembly to the passenger side (right hand) door jamb form the K8 relay. The black wire with the blue stripe is for the C pillar lights. This is part of the 13A449 main taillight wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid...

Used taillight wiring harness repair plug and pigtail from the K8 relay to the taillights for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness.Good for both Standard and XR7 models*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link...

Used taillight wiring harness repair plug and pigtail that connects to the 14405 harness to the passenger side (right hand) door jamb from the K8 relay. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

Used taillight wiring harness repair plug and pigtail connection from the 14401 harness at the driver side (left hand) door jamb for the Mercury Cougar produced before 1/3/1967. This is part of the 13A449 main taillight wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Used taillight wiring harness repair plug and pigtail connection at the driver side (left hand) door jamb. This is part of the 13A449 main taillight wiring harness.Good for both STD and XR7 models*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...

Used taillight wiring harness repair plug and pigtail connection at the driver side (left hand) door jamb on the Mercury Cougar. This is part of the 13A449 main taillight wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail for the K8 relay to the taillights for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on...

Used taillight wiring harness repair plug and pigtail from the driver side (left hand) C pillar light to the plug at the 14405 harness and driver side door jamb. This is part of the 13A449 main taillight harness.Good for both STD and XR7 models.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no...

Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) back-up light on the Mercury Cougar. This is part of the 13A449 main taillight wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) back-up light on the Mercury Cougar. This is part of the 13A449 main taillight wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair eyelet and pigtail power lead from the circuit breaker to the taillights on the Mercury Cougar. This is part of the 13A449 main taillight wiring harness.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

Used taillight wiring harness repair eyelet and pigtail from the circuit breaker to EACH taillight and license plate light. This harness section contains a pink resistor wire which should not be cut or spliced. That is because the wire's ohm resistance is based upon it's length. Cut it, and she's done for. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject....

Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) outboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

Reproduction sway bar mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Reproduction sway bar clamp mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Concours correct reproduction of the front sway bar clamps used on all 67 - 70 Cougars and Mustangs with the competition suspension option, or 15/16th" sway bar. Never available until now. Exactly like the originals in every detail. Standard for all Shelbys, Boss 302s, and Cobra Jets. Stamped and formed just like the originals.

Bolt kit for installing front sway bar clamps to the body for any 1967-68 Mercury Cougar or Ford Mustang. 3/8" bolts for 1967-68 cars. Starting in 1969, the bolt size was changed to 5/16". This size of bolt is obviously stronger and can be used on all cars 1967-73. 

Original passenger side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this...

Original driver side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as:...

Used under dash wiring harness repair plug and pigtail for the driver side door to the door courtesy light. This is a black wire with a male plug at one end and is part of the 14401 main under dash wiring harness.

Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) inboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) inboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) center taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) outboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used 4 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for parking brake and low fuel indicators. Yellow and green light sockets. These are the same sockets for the parking brake and low fuel warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.

Used 3 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for seat belts and door ajar indicators. Blue and red light sockets. These are the same sockets for the seat belt reminder and door ajar warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.

Reproduction under hood wiring harness repair plugs and leads that go from the under hood harness to the starter solenoid on the Mercury Cougar or Ford Mustang.  Sold as a pair.

Used taillight harness wiring repair pigtail from the K8 relay to the passenger side (right hand) door jamb for the 67 - 68 Mercury Cougar Standard / XR7

Used taillight wiring harness repair pigtail from the K8 relay to the taillight harness plug on the 1967 Mercury Cougar.

Reproduction pigtail for repairing the ignition switch on the 67 Cougar or Mustang. 

Used under dash wiring harness repair plug and pigtail to the turn signal relay for your Mercury Cougar. This is part of the 14401 main under dash wiring harness. This late version has a single purple wire in the end plug position. Early version is identified by the double purple wire on the end, We do not know the approximate cutoff date.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars...

Used under dash wiring harness repair bare ignition switch plug for the Mercury Cougar. This is the plug only, no wiring pigtail, and is part of the 14401 main under dash wiring harness.

Used wiring pigtail that runs from the taillight harness to the Back up light housing on the 67 - 68 Cougar. Works on both Standard and XR7 models.

Used wiring pigtail that runs from the main under hood harness to the headlight harness, parking light harness and differential switch. Located above the left hand (driver side) kick panel behind the heater controls.

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

Used wiring harness that runs from the 14290 under hood harness to the voltage regulator on the 67 - 68 Standard Cougar.

Used wiring harness that runs from the 14290 under hood harness to the voltage regulator on the 67 - 68 XR7 Cougar.

Used wiring pigtail that runs from the 14290 under hood harness to the right hand (passenger) side park / turn signal. 

Used voltage regulator plug for the 67 - 68 Mercury Cougar. Plug end only, does not include any wiring.

Used wiring pigtail that runs from the 14209 under hood harness to the passenger side horn.

Used wiring pigtail that runs from the 14209 under hood harness to the driver side horn.