Windows / Glass

Used passenger side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, tinted vent glass and glass frame with 1967 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used electrical contact kit for the foot operated electric wiper actuating device. Most times these contacts have been fried, so instead of replacing the whole pedal you can now replace the electrical portion of the pedal and get it back to working condition.

Top screw on the wing or vent window frame on any 1967-68 Mercury Cougar or Ford Mustang. Screw attaches the door glass run insert to the chromed vent frame at the top. Screw accessible when door is open top leading edge of wing window frame. *Item of Note - screw is slightly too long. The tip could scratch the front edge of the door glass or chrome trim on top of the door window. We suggest grinding down the tip about 1/8 inch, prior to installation. We have looked and this is the only...

C7ZB-17664-A Foot operated electric wiper actuating device for engaging the windshield washer pump or to cycle your windshield wipers once manually in light rain. Ford MPC number C7ZZ-17664-A. For any 1967 - 1968 Mercury Cougar and Ford Mustang.NOTE: If your electrical points are fried, you can simply replace them with the used contact replacement kit. Please note the Core deposit ...

Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock. Thanks for the plug Mark!: My first deal with Don was clear back in the...

C7ZZ-65222A89-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A.

C7ZZ-65222A88-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A.

Insert to replace the worn rubber and felt channel guide for the door glass in your cool Cat or precious Pony. These units feature original looking felt. Top molded pieces are bonded securely and has steel inserts for added strength. Sold in a pair. There are three brands of this particular piece, we carry the best even though our price is less than most everyone else. Replaces Ford part #C7ZZ-6521546-A and C7ZZ-6521547-A. Check out our handy diagram below to find other '67-'68 door parts you...

Reproduction hose grommet for the windshield washer pump through the firewall. Good product, will work with original hoses. Replaces Ford part number C7ZZ-17545

The 1967 - 1968 windshield washer kit varies slightly from the 1969 - 1970. Replaces Ford part #: C7ZZ-17543.

Linkage arm that attaches to the windshield wiper motor that is unique to the 67 - 68 Mercury Cougar and Ford Mustang. These are marked 7Z, among other things the slot is specifically indexed for the 67 - 68 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

375897-S White plastic 5/16" washer for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 2 per side, sold individually.

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber, and the rubber to the window channel. Non hardening and stays pliable, 1/10th of a gallon. You will need no less than one tube per window as you will need to put a bead inside the U channel of the rubber weatherstrip as well as a generous bead on the car. This product additionally was used for securing...

Special nut with large diameter spinning washer for the set screw for the door glass adjustment. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure. See also 378696-S for the vent window and front door channel set screws. Ford part number 33797-S.

34392-S7 5/16 inch nut for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

[No Description Provided]

Driver side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.

Passenger side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.

Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. This unit will have all three window stops and both window guides still attached. Ford part # C7ZZ-6529753-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Good used passenger side (right hand) quarter window guide for the Mercury Cougar or Ford Mustang. This unit will have all three window stops and both window guides still attached. Ford part # C7ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Good used passenger side (right hand) quarter window guide for the 1969 -70 Mercury Cougar or Ford Mustang. Ford part # C9ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Good reproductions but we suggest you consider our good used original FORD units that have been closely inspected and have had new plastic rollers installed. *NOTE* Originals were painted semi gloss black. Often the regulator is fine and all you need is new rollers. Check out this helpful youtube video on how to replace these rollers.

Good used original FORD part that has been closely inspected for rust on the roller shaft / stud and bent arms. 1967 & 1968 units will have new rollers included. We are of the opinion that these are better quality than the off shore reproductions that are available. With a little elbow grease this good quality originals will have years of good service left in them. Unlike the reproductions these, come with a one year warranty. Ford Part Numbers: C5ZZ-6530306-A, C5ZZ-6530307-A,...

Good reproductions but we suggest you consider our good used original FORD units that have been closely inspected and have had new plastic rollers installed for half the price! *NOTE* Originals were painted semi gloss black. Often the regulator is fine and all you need is new rollers. Check out this helpful youtube video on how to replace these rollers.

Good used original FORD part that has been closely inspected for rust on the roller shaft / stud and bent arms. 1967 & 1968 units will have new rollers included. We are of the opinion that these are better quality than the off shore reproductions that are available. With a little elbow grease this good quality originals will have years of good service left in them. Unlike the reproductions these come with a one year warranty. Ford Part Numbers: C5ZZ-6530306-A, C5ZZ-6530307-A,...

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet. Sold individually. 2 rollers required per window, 4 rollers required per car. Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" Diameter Here's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: ...

Reproduction of the very hard to find window roller for the window channel / quarter window frame on the 67 - 68 Cougar and Mustang. Doubles as both the single and double type roller (with the included support washer). Included in this kit are: One roller, one rivet, one wavy washer, one flat washer, and one support washer, measures exactly 1" wide. Rivet is for a 1/4" hole. 2 required per door glass channel, 3 per quarter window frame. Sold individually. Replaces Ford Part # C8SZ-57262A32...

Used roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Also found on all 1967-68 Mercury Cougar and Ford Mustang door window channels. Often times one of the rollers breaks off and allows chattering of the window movement. Sold individually: 3 total rollers on each side of the quarter window brackets. 2 like this, and 1 single piece roller (item 11-0287). 2 total rollers with the two piece plastic rollers on each of the door...

Used single plastic roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Note that there is only one of this style of roller on each quarter window. This is a simple white plastic roller and a rivet. Note that there are 2 rollers with 2 pieces of round white plastic. Often times one of the rollers breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the...

Sold individually, three per side, six per car required. These often get destroyed when you go to replace your door window regulator slides. Three of these are used to install the C7ZZ-6523288-A track. Stainless steel. Thread size: 8/32 Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator?...

Screw for mounting wing window pivot bracket. Two per car, sold individually.

Fits all Mustangs, Cougars, Fords 65-70. Attaches the striker on the door pillar, the big screws. Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

Reproduction door to window seal for the early 1967 Mercury Cougar and Ford Mustang. These are copies of ones for use before 12/14/1966. Install at the rear of the door at the edge of the door window. Replaces Ford part #: C7ZZ-6520558-B and C7ZZ-6520559-A. Sold as a pair. This part is often listed incorrectly under C7ZZ-6520588.

It is not often we get perfect used rubber, but nothing fits like OEM!The Engineering number on the bottom of the driver side reads C7ZB-6521449-ACheck out our video below for helpful tips on disassembling your vent and quarter windows: ...

Passenger side only. Less than perfect fit, no returns on this item. Replaces Ford Part # C7ZZ-6521448-ACheck out our video below for helpful tips on disassembling your vent and quarter windows: ...

Seals between chrome vent frames and door on exterior side. Stops water from leaking between vent window and door. Keep in mind that this seal comes as one strip and it meant to be cut down the middle. Sold as a pair. Replaces Ford part #: C6OZ-6322280 or C6OZ-63222A80-A.

These high quality vent window seals are the first on the market to replace the original Ford part exactly. This is the small seal at the front of the door and next to the door weatherstrip. Sold as a pair. Replaces Ford Part #: C7ZZ-6522332/3, C7ZZ-65223A32-B, C7ZZ-65223A33-B, C7ZZ-65223A32-C & C7ZZ-65223A33-C.

Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183

378696-S Special set screw for the front door channel and vent window frame. This one is longer than the one that installs in the rear door window guide. This set screw has a 5/32" hex head with 5/16" NC threads and is 1-7/8 inches in overall length. This set screw also has a 1-1/8 inch diameter shoulder. Sets and holds your front door glass and vent window angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual...

22992 SPRING Tension spring for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

22992 "D" shaped top washer, Ford called it a 'stop'. See assembly picture. 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side, sold individually.

Reproduction stop bracket for the rear quarter window regulator on any 1967-68 Mercury Cougar and 1965-68 Ford Mustang Coupe and convertible models. Stop bracket for the quarter window regulator arm. Comes with used bolt as shown. One bracket per side, same bracket for driver or passenger side. Replaces Ford part number C4ZB-65303A12 also referenced as 29822 in the assembly manuals.Also available used. ...

Stop bracket for the rear quarter window regulator on any 1967-68 Mercury Cougar and 1965-68 Ford Mustang Coupe and convertible models. Stop bracket for the quarter window regulator arm. Comes with used bolt as shown. One bracket per side, same bracket for driver or passenger side. Reproduction also available. Ford part number C4ZB-65303A12 also referenced as 29822 in the assembly manuals. ...

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video below: ...

Reproduction pair of vent / wing window handles for the Mercury Cougar or Ford Mustang.

Reproduction driver side (left hand) vent window frame for the Mercury Cougar or Ford Mustang. NOTE! Whereas you can make these off shore reproductions work we have found that virtually every angle, screw hole and dimension is found to be slightly to moderately off when comparing to the originals. No returns please. Check out our video below for helpful tips on disassembling your vent and quarter windows: ...