Wheels / Caps

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 1-1/4 from wheel surface. These will work with our aftermarket Ford wheels without trim rings. These have the Dill 627 caps. Same as the 1960's cars.

Original space saver tire from a 1968-70 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-70. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.Just the tire, perfect for someone who has a dated wheel.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Original space saver tire marked B.F. Goodrich F78-14. Display only, it can not be inflated. Rear side wall has damage. From a 1970-71 Mercury or Ford. Bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? Has the good tread design, single fill valve stem, but with damaged sidewall. This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is a...

Original space saver tire marked F78-14 B.F. Goodrich, from a 1970's Mercury or Ford. These were optional in 1968-73. It has the smaller hub size and single valve stem. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire. *NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Used simulated wire spoke hubcap with 3 bar spinner center / wheel cover that is in average condition with minor curb scrapes. The spinner was discontinued in 1967 so only the early models would have them in 67.Ford part # C7WY-1130-C

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard. These 5-1/2 inch wheel will fit over stock disc brake calipers 1968-73. This 5-1/2 inch wheel is...

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 16 individual pads in a package.

Used 14x5-1/2" styled steel wheel for your mercury Cougar. One year only offering in this size with a total width of 6- 1/2", a 3-7/8" backspacing, and a very small 1-13/16" center hole. Will not fit 1968 or newer Cougars equipped with disc brakes as the wheel will not fit over 1968 and up disc brake calipers. Will not fit 1967 Cougars that have been retrofitted with newer single piston disc brakes. Shipped bare, without center cap or trim ring. Various conditions with minor blemishes, but no...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14"x6" styled steel wheel with correct argent silver finish between the chrome spokes on the center for your Mercury Cougar. Gorgeous reproduction of the...

This wheel was optional on any 1969-70 Cougar except the 1969 Eliminator which came standard with the 12 hole painted rally wheel. In 1970 the Eliminator used this SS wheel but it was optional, not standard equipment.  These are exact reproductions in every way except they are welded, not riveted to the center section.NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do...

Used 14x7" styled steel wheel for your Mercury Cougar. This painted Kelsey Hayes wheel used with small cap and brushed finish trim ring that are sold separate. Cap and lugs are sold separately. Total width is 8" with a backspacing of 4".Ford part # D0ZZ-1007-C.

Reproduction 15x7 chrome styled steel wheel for your Cougar or Mustang. Technically correct for Mustang because of the holes being placed in the center of the arms instead of in the inserts like the Cougar, but will fit both vehicles. Gorgeous reproduction of the original 1968 Mustang styled steel wheel. Correct in every way except that the outer band is welded on instead of riveted to the center section. This wheel has a total width of 7", backspacing is 4" and the center hole is...

Reproduction chrome center cap with blue background and chrome Mercury man logo for the Mercury Cougar. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the...

Reproduction chrome center cap with red background and chrome Mercury man logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from...

Chrome center cap with Blue background and chrome walking cat logo for the Mercury Cougar. Better than original! New from Scott Drake. These quality center caps feature our high quality chrome bezels. Check out the details in our "Cougar" lens. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing,...

Reproduction chrome center cap with red background and chrome walking cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good...

Short steel chromed valve stem for Ford wheels or any steel wheel with a 0.453" hole. Clamp in or bolt in style, sticks up 3/4 from wheel surface, 200psi maximum pressure. These will work with our aftermarket Ford wheels without trim rings. These are not compatible with our aluminum wheels.Premium grade, marked for "High Temperature".

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems for installation of the new Legendary aluminum wheels. These really only fit the Magstar style wheels; we recommend the 3/4" lug nuts for all the other Legendary wheels for clearance reasons. Conical Head: 13/16" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems. Specifically for installation of the new Legendary GT7 and 1966 Shelby wheels. Thread Size: 1/2" Bolt Pattern Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome lug nuts and 4 chrome valve stems for installation of the new aluminum Legendary Series wheels. Tapered for correct fit. This 3/4" size is what we recommend you use with the Legendary wheels, since the clearances are too tight for 13/16" nuts. Conical Head: 3/4" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide.This ring will have one or two small scratches or dings that will be noticeable. Replaces Ford part number D0DZ-1210-A.Fits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972 Ford...

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

Used on the 1970 Mustang, 1970 - 1971 Cyclone and Torino and 1971 1972 1973 Cougar style steel wheel 14 x 7". Master Parts Catalog description: 15-1/4" O.D., 11" I.D., 2-3/4" wide. This grade A brushed beauty ring will look right at home on a low mile car, no curb rash!!! Ford part number D0ZZ-1210-B Ford superseded this part with part number in 1974 with D4WY-1210-A which looks the same just a little bit deeper at 2 7/8" deep ...

Used on the 1970 Ford Mustang, 1970 - 1971 Cyclone and Torino and 1971 Cougar style steel wheel 14 x 7". Master Parts Catalog description: 15-1/4" O.D., 11" I.D., 2-3/4" wide. This ring will have one or two very small scratches or dings that will not be easily fixed, driver quality.Ford part number D0ZZ-1210-BFord superseded this part with part number D4WY-1210-A

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

Used grade A trim ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 1968 SS wheel. No dings or scratches that cannot be buffed out. sold individually.Replaces Ford part number C6ZZ-1210-A.

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most customers will be happy with our reproduction ring that is not brushed....

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have slight blemishes that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, most customers will be happy with our reproduction ring that is not brushed. This...

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have one or two very small scratches or dings that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

This trim ring was used in 1967 and is very close (not as deep) to the 1969 - 1970 trim ring. 1968 was deeper and was brushed on the inner portion. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep. Ford Part number C6ZZ-1210-A.

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

Used chrome / black center cap for the 67 - 68 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers.Fits:1967 Mercury Cougar1968 Mercury Cougar

Used / refurbished center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. These are always faded, so we've "restored" a few with Sharpies, as shown in the picture. Believe it or not, it works pretty well and allows the shiny aluminum to show through the red. Be advised that the sharpie treatment doesn't hold up very well to rain and weather, so this is best for garaged...

Set of 4 Chrome center caps with red background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Used chrome / red center cap for the 1967 and 1968 Mercury Cougar and Ford Mustang Equipped with the Wire Spoke Hubcaps / Wheel Covers. Fits:1967 Mercury Cougar1968 Mercury Cougar

The only reason you would buy an original used unit is that you would want to match your existing original caps. The reproductions we carry are actually much better quality than the originals, as they will never fall off. Chrome center cap with black background and chrome Mercury man logo. Came from the factory on 1967 and 1968 Mercury Cougars with Styled Steel Wheels, but will work on any 67-70 with Styled Steel Wheels.Fits the following models with style steel wheels:1967 Mercury Cougar1968...

These original clip on center caps are an inferior design compared to our reproductions that screw on from the back. The originals had varying shades of blue, whereas the repro has a solid blue. The only reason you would purchase this fragile expensive used cap is to match what you currently have on a very original car. When using center caps on Legendary wheels, you will need these adapter plates. Ford part # C9WY-1130-BCheck out our video on Legendary Wheels below: ...

QUALITY HAS GONE DOWN ON THESE CAPS, UNTIL THE SUPPLIER CAN CORRECT THE ISSUE, WE WILL NO LONGER HAVE THESE AVAILABLE.Reproduction chrome center caps that feature a magenta background and a chrome XR7-G logo for the Mercury Cougar. The center caps are die-cast like the originals were, other reproductions out there are made on a lathe with aluminum stock. These units are sold individually. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing...

This XR7-G center cap adapter cone was used in conjunction with the RADER wheel and is needed to mount the center cap to the aluminum centered wheel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know...

Notice the blemishes on this NOS cap? This is very typical of what we see on many NOS caps. This chrome XR7-G center cap with magenta background and chrome XR7-G logo is designed to fit the RADER chrome cone adapter or mount directly to the 1968 chrome style steel wheel.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or...

Used original chrome center caps with magenta background and chrome XR7-G logo for the XR7-G styled steel wheel.

QUALITY HAS GONE DOWN ON THESE CAPS, UNTIL THE SUPPLIER CAN CORRECT THE ISSUE, WE WILL NO LONGER HAVE THESE AVAILABLE. Correct reproduction XR7-G chrome center caps with the correct magen ta background and chrome XR7-G logo that includes three part mounting hardware. These are die-cast just like the originals, other reproductions out there are made on a lathe with aluminum stock. Sold individually. Ford part # C8WY-1130-F. *NOTE* When installing these die cast center caps, keep in mind over...

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes, stress cracks in plastic center or pits in die-cast. Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red background. This cap is not correct for Cougar, but was found on other Mercury products such as the Montego.

Used grade A near perfect dog dish style hubcap / Wheel Cover for the 1970 Mercury Cougar Eliminator. This same cap was standard equipment for the 1971-73 Mercury Cougar and was used with dealer installed trim rings when the optional 15x7" wheels were ordered on 1971-72 Cougars. There were two versions for this cap, one had a brushed finish where the other had a bright finish. These are all driver quality with some dings and or scratches. The one pictured is brushed, but we often have both in...