Transmission

(7521) Correct Contour and fit. Connects pedal to Equalizer bar. Fits all engine sizes 3 and 4 speed. Replaces Ford Part #: C9ZZ-7521-C.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

Manual transmission clutch throw out bearing for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is with a 10 inch disc.

Reproduction transmission cooling lines made of OE steel for the late production 1968-70 Mercury Cougar or Ford Mustang equipped with the C-6 automatic transmission. These lines are also available in stainless steel and are sold in pairs.

Reproduction transmission cooling line made of stainless steel for the Mercury Cougar produced from late 1968 through 1970 that came equipped with the C-6 automatic transmission. These lines are also available in OE steel and are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 351W and FMX transmission. These are sold in pairs

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351W engine. These lines are sold in pairs.

First generation Cougars 1967 and 1968, used a single bracket for C4 automatics and both 3 speed and 4 speed manual transmissions. This bracket also carried over to 1969 and 1970 with 351 or Boss 302 engines and either 3 or 4 speed manual transmissions. Ford part number C7ZZ-6A023-D. This part weighs 2.28 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 1/4" on center and the passenger side 2 3/4" on center.The reproduction Dynacorn part...

For all 1969 and 1970 Cougars with H code 351-2V and M code 351-4V engines and FMX automatic transmissions. This part weighs 2.66 pounds and when set on a level surface the height of the mounting hole on the driver side measures 3" on center and the passenger side 3 1/8" on center. Ford part number C9ZZ-6A023-A. *NOTE* The picture with all four crossmembers in a line shows the three versions of the small block C-6 and FMX units in the foreground and the last is the big block C-6 unit. Notice...

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.

Reproduction transmission dipstick tube for 67 - 70 Cougars or Mustangs equipped with the C4 automatic transmission.Replaces Ford Part number C6AZ-7A020-B

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

Clutch Lever Dust Boot for the 289, 302 and 351. Replaces Ford Part #: C6OZ-7513-C.

New old stock manual transmission shift lever boot. Attaches to the bell housing on FE big block cars. 1967-70 Mercury Cougar and Ford Mustang, 1966-71 Ford Fairlane / Torino. No comparison to the repro, this is much better.  Replaces Ford Part #: C6OZ-7513-A.

This reproduction is made from the original Ford tooling and is new to the market. Well worth the few extra dollars over the previous ones offered. Replaces Ford Part #: C6OZ-7513-A.

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.

[No Description Provided]

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Reproduction alternator mounting kit for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Spacer not included, but available.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

Quality kit that offers precision fit, for use with your stock bell housing. Requires drilling of one hole as well as drilling and tapping of a second hole in your bell housing.

New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...

Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...

Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.

Remanufactured OEM Ford Boss 429 and 429 Cobra Jet manual transmission flywheel. Stamped C9AE-C. New ring gear, resurfaced clutch surface. No visible issues, no discoloration from heat. 1971 Mercury Cougar and Ford Mustang, 1970-71 Ford Torino and Mercury Cyclone and variants. 1969-70 Boss 429. Ford part number C9AE-6375-C.

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

Reproduction plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Late 1970 used the same as the 1971-73 model.Replaces Ford part # D0DZ-10718-A.

Reproduction steel inspection cover for all 67 - 70 Cougars or Mustangs with 390, 427, or 428CJ engines with the C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.

Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Used dust and safety cover for all 69 - 73 Cougars and Mustangs with the FMX (code X) automatic transmission. Access plate for the torque converter and flex-plate.

Grade B used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This cover will have some rust and a dent or creases. Find the Grade A cover here.

Reproduction inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch.Replaces Ford part number C3AZ-6366-A.

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.

According to the Master Parts Catalog, this rod was used on all 1969 Cougars equipped with a C6 transmission which includes the 390IP / 428CJ / 428SCJ. Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP / C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any other Ford product. ...

Good used lens that has not gone milky from over exposure to the sun. Not for use on the XR7 speedometer or clocks found on the XR7 or Standard models. To get these lenses looking new you will have to use a three step plastic polish like Novus or Meguires plastic polish. If your lenses are cloudy or swirled looking this will not come out as it is internal.Check out the video below on our new gauge tester: ...

Good used lens that has not gone milky from over exposure to the sun. Used only on the 69 - 70 XR7 speedometer. To get these lenses looking new you will have to use a three step plastic polish like Novus or Meguires plastic polish. If your lenses are cloudy or swirled looking this will not come out as it is internal.

These clips are used to hold the lenses in place on your cluster. Sold as a set of three.

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...