Suspension, Chassis & Drivetrain

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

This is a the economy version of our lower control arm assembly, with a spot welded on reinforcing plate. We are sorry, but we just cannot recommend this part. The Scott Drake premium version of this lower control arm is superior and costs less. In the picture, you can tell that it is lacking a rolled lip on the outer edge that the originals and the Drake Premium reproduction offers. This is a non-returnable item. Having issues with wobbly or loose steering? Check out our video on sloppy...

Straight Monte Carlo Bar in stainless steel for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C7ZZ-16A052-ARS.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on cars with 427-4V, 428CJ, 429CJ, Boss 302, Boss 351, or Boss 429. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: 8L27, November 27, 1968; 0E29, May 29, 1970. Please have your desired date in mind when calling or place it in the comments section of your on-line order. We have removed the peg leg gears and parts...

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.

Used rear leaf spring retainer for 1967 -73 Mercury Cougar with competition handling or GT suspensions. Additionally it fits 1966-71 Mercury Comet / Montego / Cycolne, 1966-71 Ford Fairlane / Torino, all with HD or GT suspensions. Identified with a stamped number "2" on the top. The inside height is 1-29/32 or 1.91 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be...

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate.The reinforced shock towers came out in late March 1968 and were used on all big block Cougars and Mustangs. 390-2V / 390-4V / 427 / 428CJ. No specific part number exists for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate. In late 1968 390-427-428 Mercury Cougar and Ford Mustang came with this reinforced tower due to a problem they were having with structural cracking. No specific part number for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

Reproduction shock tower and apron assembly  for your Cat or Pony.Here's a little film to help you fortify your flexxy feline!

Nice used driver side strut rod that fits all 1968-69 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1968-69 Torino, Cyclone, Ranchero. 1968-69 strut rods are the same as 1970-73 strut rods, but 1968-69 rods have stepped down threads at the end. Ford part number C8OZ-3468-B. Sold as a bare strut rod, we also offer the used hardware for installation...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. This listing is for the driver side only. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage.*Note - 1970-73 strut rods work equally well.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage. This listing is for the Passenger side only. *Note - 1970-73 strut rods work equally well. ...

This listing is for a premium quality pair of 1968 - 1969 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the rear on the arm to the lower...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a better value than the Chinese rods we sell.*Note - 1970-73 strut rods work equally well.

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes.  Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...