Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 97-144 of 316
$0 Price: $259.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25077 -

Also called a pumpkin, 3.00:1 open ratio. Check your door tag under "Axle". 1967 code 1 1968 code 5

$0 Price: $52.38

Buy Details

Availability: Out of Stock
Item #: 20542 -

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.

$0 Price: $292.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24485 -

390 and 427 engines with C6 automatic transmissions. Shaft diameter 3 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory.Ford part number C8WY-4602-B Ask about slip yokes. Shipping is oversized due to length.

$0 Price: $105.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24175 -

289 and 302 engines - with C4 automatic transmissions or manual three / four speed. Shaft diameter will measure 3 inches. Length 54-3/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.  Ford part # C7WY-4602-E.*NOTE* This is a two piece drive shaft.

$0 Price: $6.45

Buy Details

Availability: In-Stock Item
Item #: 26562 -

This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing bolts is so equipped.

$0 Price: $6.45

Buy Details

Availability: In-Stock Item
Item #: 26571 -

This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a slightly larger round punch to open the hole slightly. If the boot isn't seated low enough, the boot will tear and fail in short order.

$0 Price: $4.15

Buy Details

Availability: In-Stock Item
Item #: 11299 -

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. *Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #C6OA-3332-A or C6OZ-3332 ...

$0 Price: $5.25

Buy Details

Availability: In-Stock Item
Item #: 11294 -

Reproduction rubber dust seal or boot with steel reinforcing ring for front suspension inner and outer tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. This is the concours version with Ford casting number C6OA-3332-A.*Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #...

$0 Price: $15.17

Buy Details

Availability: Out of Stock
Item #: 26727 -

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

$0 Price: $75.65

Buy Details

Availability: In-Stock Item
Item #: 11439 -

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

$0 Price: $115.97

Buy Details

Availability: In-Stock Item
Item #: 11440 -

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

$0 Price: $100.08

Buy Details

Availability: In-Stock Item
Item #: 11441 -

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

$0 Price: $44.87

Buy Details

Availability: Rare / NOS Part
Item #: 26719 -

Ford original eye let bushing 100% correct for the 67-69 Cougar without competition handling, but will fit on any 67-73 cat including those with competition handling. Ford Part #: C4DZ-5781-C.

$0 Price: $21.85

Buy Details

Availability: In-Stock Item
Item #: 26749 -

This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS.  Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...

$0 Price: $30.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23875 -

Used driver side (left hand) shock tower brace for the Mercury Cougar and most Ford Mustangs. Solid, undamaged brace. Consider our brace kits - best value. Ford part # C5ZZ-16A053-B.*NOTE* Excludes 1967-68 Mustang Convertible.

$0 Price: $30.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23874 -

Used passenger side (right hand) shock tower brace for the Mercury Cougar and most Ford Mustangs. Solid, undamaged brace.Consider our brace kits - best value. Ford part # C5ZZ-16A052-C. *NOTE* Excludes 1967-68 Mustang Convertible.Here's a little film to help you fortify your flexxy feline! ...

$0 Price: $338.27

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 18968 -

Reproduction Mercury Cougar and Ford Mustang firewall.Here's our little film to help you fortify your flexxy feline!

$0 Price: $60.89

Buy Details

Availability: In-Stock Item
Item #: 41640 -

Reproduction driver side (left hand) floor pan to cowl side panel for Mercury Cougar and Ford Mustang. Normal 0 false false false EN-US X-NONE X-NONE Here's our little film to help you fortify your car! ...

$0 Price: $45.55

Buy Details

Availability: In-Stock Item
Item #: 10863 -

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1968 Mercury Cougar and Ford Mustangs. New part with a fine threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C3AA-4906-C, this version has fine threads. The version most often seen on the 1969-70 is C9OA-4906-A. It will have a course threaded mounting stud.

$0 Price: $29.15

Buy Details

Availability: Out of Stock
Item #: 13730 -

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

$0 Price: $29.15

Buy Details

Availability: Out of Stock
Item #: 13731 -

Reproduction passenger side (right hand) inner front frame patch for the Mercury Cougar or Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

$0 Price: $706.05

Buy Details

Availability: In-Stock Item
Item #: 25717 -

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

$0 Price: $706.05

Buy Details

Availability: In-Stock Item
Item #: 25718 -

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2) Outer Tie Rods, (2) Inner Tie Rods, (1) Idler Arm, (2) Spring Perches. If you...

MSRP:$219.99
$219.99 Price: $178.07

Buy Details

Availability: In-Stock Item
Item #: 10539 -

Reproduction full one piece front frame rail for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510219-B.Here's our little film to help you fortify your flexxy feline!

MSRP:$219.99
$219.99 Price: $198.35

Buy Details

Availability: In-Stock Item
Item #: 10540 -

FULL inner and outer passenger side (right hand) reproduction one piece frame rail for the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510218-B.Here's our little film to help you fortify your flexxy feline!

$0 Price: $49.15

Buy Details

Availability: In-Stock Item
Item #: 41631 -

Reproduction driver side front inner apron for both the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

$0 Price: $7.27

Buy Details

Availability: In-Stock Item
Item #: 10576 -

Gasket for sealing the 8 inch third member in most corporate Ford rear ends. Typically found in all 1967-68 Mercury Cougar and Ford Mustang with 289 or 302 engines. Exception for Mustangs with the GT option, those cars would have had 9 inch rear ends.

$0 Price: $30.84

Buy Details

Availability: In-Stock Item
Item #: 16150 -

This gasket goes between the rear axle flange and the backing plate on the differential. It fits all Mustangs from 1967 - 1970.

$0 Price: $2.27

Buy Details

Availability: In-Stock Item
Item #: 13002 -

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

$0 Price: $107.17

Buy Details

Availability: In-Stock Item
Item #: 11370 -

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

$0 Price: $139.95

Buy Details

Availability: In-Stock Item
Item #: 31835 -

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

$0 Price: $114.49

Buy Details

Availability: In-Stock Item
Item #: 31836 -

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

$0 Price: $74.55

Buy Details

Availability: In-Stock Item
Item #: 26726 -

Import reproduction. Fits 1967-70 Mercury Cougar or Ford Mustang without power steering. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Click on images to enlarge. ...

$0 Price: $132.15

Buy Details

Availability: In-Stock Item
Item #: 26694 -

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

$0 Price: $58.18

Buy Details

Availability: In-Stock Item
Item #: 26722 -

NOTE - Some customer are experiencing problems with this economy idler arm, the castle nut on top is causing clearance issues with the bolt on the top arm.Import reproduction. Fits 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering.

$0 Price: $99.55

Buy Details

Availability: In-Stock Item
Item #: 26715 -

Premium grade of idler arm. Fits all 1967-70 Mercury Cougar and Ford Mustang. If you have loose / sloppy steering, replacing this part could help tighten things up. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Drag link hole size: 5/8" Customer feedback: Hey, just wanted to thank you for your prompt service. Last Friday...

$0 Price: $49.15

Buy Details

Availability: In-Stock Item
Item #: 41627 -

Reproduction passenger side front fender apron that has the shelf for installing the battery tray. *Restoration Hint* This section of metal was VIN stamped, consider welding in the stamped VIN section to keep your car whole.Here's a little film to help you fortify your flexxy feline!

$0 Price: $7.35

Buy Details

Availability: In-Stock Item
Item #: 26617 -

Reproduction Rear Leaf Spring Center Mount Insulator Pad for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody StyleNotesYearMercur...

$0 Price: $28.67

Buy Details

Availability: In-Stock Item
Item #: 42183 -

Set of Four Reproduction Rear Leaf Spring Center Mount Insulator Pads for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody...

$0 Price: $81.77

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32074 -

Used driver side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

$0 Price: $81.77

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32076 -

Used driver side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

$0 Price: $81.77

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 20410 -

Used passenger side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

$0 Price: $81.77

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32075 -

Used passenger side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

$0 Price: $344.62

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 43043 -

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

$0 Price: $295.38

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 43045 -

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...