Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Nuts and washers for attaching the rear differential carrier or pumkin or third member to the rear axle housing.Correct for all 1967-68 Mercury Cougar and 1965-68 Ford Mustang. 8 inch or 9 inch third members, all the same.
New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.
Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.
Reproduction radiator / core support for Mercury Cougar and Ford Mustang. This is the very best one made! Replaces Ford part # C7ZZ-16138-B and C7ZZ-6510852-B together.
Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.
Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.
Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!
This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...
New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...
Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.
New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.
New RTV oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.
Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.
Oil seal for rear axle on any 1968-73 Mercury Cougar or Most Ford cars with 31 spline axles. Typically only 428CJ, 427-4V, and Boss 302's got the heavy duty 31 splined axles from the factory, most Cougar and Mustangs have 28 splined axles. Seal measurements: 1-1/2 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-A.
Reproduction coil spring seat pad for the 67 - 73 Cougar or Mustang. Sold individually, 4 needed per car.
KYB Gas-a-just shocks are America's best selling performance gas shock. It's monotube design features a higher gas pressure which helps to hold the tire to road surface during severe driving conditions. N2 gas helps eliminate shock fading due to aeration and foaming. This shock is the perfect choice for the performance oriented. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.029.614.41-X- ...
These are equal in performance to other name brand high pressure gas shocks at a significant lower price. These shocks are best suited for drivers looking for firm ride with a solid controlled “feel of the road”. These units are sold individually.
This gas shock improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock. Also, this is the most stock-looking shock since it's black and has a flat upper collar. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.259.334.92-X- ...
Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually
If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!
Excellent condition tower as cut from a Western parts car. No specific part number for this structural front suspension section.Generic Ford part # C7ZZ-16055-D or E, includes apron and side member.Here's a little film to help you fortify your flexxy feline! ...
We highly suggest you look at our mint condition used towers for about the same price. Why mess around with repo when you can get FoMoCo?!Here's a little film to help you fortify your flexxy feline!
Excellent condition tower as cut from a Western parts car. If you are replacing two towers because of cracks, we strongly suggest upgrading to a 1969-70 pair of reinforced towers. The 69 and 70 towers are an exact fit into your 1967-68 Ford Mustang or Mercury Cougar. There are no specific part numbers for this structural front suspension section.Generic Ford part #s C7ZZ-16054-C or C7ZZ-16054-E, includes apron and side member. Here's a little film to help you fortify your flexxy feline! ...
Used driver side shock tower and apron assembly for the Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!
Reproduction passenger side shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!
Used passenger side shock tower and apron assembly for the Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!
Solid, undamaged driver and passenger side shock tower braces. Fits all 1967-68 Mercury Cougar and Ford Mustang. Ford part #s C5ZZ-16A053-B driver side (left hand) and C5ZZ-16A052-C passenger side (right hand). *NOTE* Excludes 1967-68 Mustang Convertible. **Installation Tip** These brackets attach under the cowl lip. ...
Individual reproduction shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.
Individual reproduction shock tower cap or coil spring cover in black for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.
Individual used shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. While not technically restored original, we offer these to complement our chrome export braces and Monte Carlo bars. Ford part # C7ZZ-18A017-A.
Used shock tower cap for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. These used pieces are superior to the reproductions because they are constructed from thicker metal. Plus, you just can't beat original FoMoCo!Ford part # C7ZZ-18A017-A.
Reproduction passenger side (right hand) floor pan cowl side panel for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your car!
This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.
Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.
Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.
This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S
Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs.
Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs. These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H
DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.
Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.
C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.
This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...
Inner tie rod end for 1967 - 1969 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: C7ZZ-3A131-A
Outer tie rod end for 1967 – 1969 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: C7ZZ-3A130-A. *Note – Excludes 1969 Boss 302 Eliminator and Mustang. *Note – Use 1970-73 arm for vehicles with the 'Granada' disc brake conversions.
Reproduction passenger side (left hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!
Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!
Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.
Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.