Suspension, Chassis & Drivetrain

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

High Performance Coil Spring Perches offer a very affordable upgrade to stock spring perches with rubber bushings. These are made with synthetic elastomer bushings which are similar to polyurethane in performance and longevity, but will not squeak like polyurethane. The perch can rotate 360 degrees on the shaft, which allows the front suspension to articulate freely. This feature also eases the installation of the coil spring. Zerk grease fittings are installed and locking nuts are included....

Nuts and washers for attaching the rear differential carrier or pumkin or third member to the rear axle housing.Correct for all 1967-68 Mercury Cougar and 1965-68 Ford Mustang. 8 inch or 9 inch third members, all the same.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

Reproduction coil spring seat pad for the 67 - 73 Cougar or Mustang.  Sold individually, 4 needed per car.

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.