Suspension, Chassis & Drivetrain

Used rear leaf spring retainer for 1968 -73 Mercury Cougar with standard or non-GT / non- competition handling suspensions. Additionally it fits most 1966-70 Mercury Comet / Montego, 1970-71 Ford Torino. Identified with a stamped number "6" on the top. The inside height is 1-3/4 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be some erosion due to...

Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

Oil seal for rear axle on any 1968-73 Mercury Cougar or Most Ford cars with 31 spline axles. Typically only 428CJ, 427-4V, and Boss 302's got the heavy duty 31 splined axles from the factory, most Cougar and Mustangs have 28 splined axles. Seal measurements: 1-1/2 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-A.

Reproduction coil spring seat pad for the 67 - 73 Cougar or Mustang.  Sold individually, 4 needed per car.

Correct shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Measures 3-1/2 inches from center to center. Bushing dimensions: Length 1 1/8", outside diameter 1" (shaft piece) - 1 1/4" (end piece), hole diameter 1/2" Sold individually, two required per car. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Correct length (3-1/2 inches from center to center) and construction shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Complete Set of 1" leaf spring poly bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. May be dropshipped. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

Complete Set of 1" leaf spring rubber bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

KYB Gas-a-just shocks are America's best selling performance gas shock. It's monotube design features a higher gas pressure which helps to hold the tire to road surface during severe driving conditions. N2 gas helps eliminate shock fading due to aeration and foaming. This shock is the perfect choice for the performance oriented. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.029.614.41-X- ...

These are equal in performance to other name brand high pressure gas shocks at a significant lower price. These shocks are best suited for drivers looking for firm ride with a solid controlled “feel of the road”. These units are sold individually.

This gas shock improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock. Also, this is the most stock-looking shock since it's black and has a flat upper collar. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.259.334.92-X- ...

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the comfort shock for those looking for a softer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the performance shock for those looking for firmer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

This gas Shock Absorber improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock.  These shocks are sold individually and are designed more specifically to work with Cougars as opposed to Mustang. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop19.3711.308.07X-- ...

Application: most 1967-1973 with any V-8 engine. A Right and Left bracket are needed for most applications. Including all 1968 - 1970 428 CJ automatic transmission Cougars. **Excludes 1969 - 1970 Boss 302 & 428 Cobra Jet 4 speed Cougars. That application had staggered rear shock plates. Hint - that would be two C9OZ-5796-C right side shock plates.Replaces Ford part number C9OZ-5796-B.

Passenger side shock mounting plate for any 1967-73 Mercury Cougar with any V-8 engines. A passenger side and **driver side bracket are needed for most applications.  **Excludes 1969 - 1970 Boss 302 & 428 Cobra Jet 4 speed Cougars. Additionally 1972 - 1973 351CJ (Q code engines - all transmissions) which all came with staggered rear shocks, which was part of those years Competition Handling Package. These applications had staggered rear shock plates. Order two C9OZ-5796-C right...

This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end and 351 or larger engine.Here's a little film to help you fortify your flexxy feline! ...

This is the best upgrade tower for your Cougar or Mustang that does not have the factory reinforcement plate. 1969 features the largest plate of all years 1968-70 and will fit perfectly without modification into any year 1967-70. If both of your towers are cracked this is a no brainer, if only one of your towers are cracked then it would look out of place to have one tower that is reinforced and one that was not. No specific part number for this structural front suspension section. For 1970,...

We highly suggest you look at our mint condition used towers for about the same price. This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end. All Cougars also came with 351 or larger engines for those years as well, except for the 302...

This is the best upgrade tower for your Mustang or Cougar that does not have the factory reinforcement plate. 1969 features the largest plate of all years 1968-70 and will fit perfectly without modification into any year 1967-70. If both of your towers are cracked this is a no brainer, if only one of your towers are cracked then it would look out of place to have one tower that is reinforced and one that was not. No specific part number for this structural front suspension section. For...

Reproduction driver side (left hand) shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) shock tower and apron assembly for Mercury Cougar or Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Solid, undamaged, used driver side (left hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your buck! Ford part # C9ZZ-16A053-A. *NOTE* Excludes 1969-70 Boss 429.Here's our little film to help you fortify your flexxy feline!

Solid, used, and undamaged passenger side (right hand) shock tower brace for Mercury Cougar and Ford Mustang. Consider our brace kits for the best bang for your hard earned buck! Ford part # C9ZZ-16A052-A. *NOTE* Excludes 1969-70 Boss 429.

Reproduction shock tower brace nuts and bolts for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Used, solid, and undamaged shock tower braces for all 1969-70 Mercury Cougar and most Ford Mustangs. Includes 4 used 7/16"-14 x 1-1/4 inch cowl attaching bolts. Ford part #s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand).  *NOTE* Excludes 1969-70 Boss 429. **Installation Tip** These brackets attach 'under' the cowl lip. Here's our little film to help you fortify your flexxy feline! ...

Individual reproduction shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual reproduction shock tower cap or coil spring cover in black for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual used shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. While not technically restored original, we offer these to complement our chrome export braces and Monte Carlo bars.  Ford part # C7ZZ-18A017-A.

Used shock tower cap for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. These used pieces are superior to the reproductions because they are constructed from thicker metal. Plus, you just can't beat original FoMoCo!Ford part # C7ZZ-18A017-A.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part # C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Includes both the left hand and right hand strut rod arm. These are required to install the reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C & C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but similar) from one end...

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C9ZZ-5482-D Factory used sway bar for any 1969 Cougar with optional Competition Handling Package. Factory identified with a single 'Green' paint stripe. *Excludes 428CJ and Boss 302 cars, those cars were factory built with a 15/16 inch sway bar. This factory used front sway bar, does not include any mounting brackets or end link kits.

C9ZZ-5482-A 1969 Standard used factory front sway bar. 3/4 inch in diameter. This factory used front sway bar, does not include any mounting brackets or end link kits.

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...