Daniel Carpenter / Dennis Carpenter

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug size: 1 1/2"   also used for the electric headlight conversion kit for the firewall pass through body plug.  

New set of floor kick panel fresh air vent gaskets / seals for all 1969-1970 Mercury Cougars and Ford Mustangs. Die cut gasket copied from originals that have mounting holes in them. These foam gaskets are 1/4 inch thick. Casting number as seen on seal reads C9ZA-18B290-D. Replaces Ford part # C9ZZ-6501999.

This kit is designed for the Mercury Cougar and Ford Mustang A/C box.Replaces part # D1ZZ-18500-A.Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

These 1969-70 Mercury Cougar chrome door handle gaskets are the closest fit to the original Ford gaskets on the market. 4 pieces as shown, enough for both door handles only, round lock gaskets sold separately.Will also work on 70-71 Cyclone and Torino.

This 4 Speed Lower Shift Boot attaches to the bottom side of your factory Hurst shifter to protect it from water and dirt. Fits 1970 Mercury Cougar and Ford Mustang, additionally fits 1970-71 Ford Torino and Mercury Cyclone with OEM Hurst 4 speed shifters. Replaces Ford part # D0GZ-7E138-B and D0ZA-7E138-B. Check out our video on rebuilding your shifter below: ...

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. *Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #C6OA-3332-A or C6OZ-3332 ...

New rubber body plug, fits 3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: frame rails at sway bar, rear floor pan, LH fender apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377977.

New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.

New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.

New rubber body plug, fits 1-1/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some of the holes include: inner frame rails at radiator, center of firewall, and side of cowl.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377936.

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-3/8" oval holes. Sold individually, Usually 1 per car. Fits 1971-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 384440.

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.

This is the driver side trim / moulding that mounts to the door window and creates the seal between the door glass and the quarter window on 69 Cougars and Mustangs. Get the seal you need for this moulding here.

Reproduction driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium piece made with the original Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction passenger side (right hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium unit that made made with orginal Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold individually, and their are usually two required per car. Replaces Ford plug marked 383181-S.

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.

Reproduction hose grommet for the windshield washer pump through the firewall. Good product, will work with original hoses. Replaces Ford part number C7ZZ-17545

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

Four per car, mounts to fenders. Replaces Ford part #: C7WY-16758.

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips. If correctness is not an issue for you, you can get the Midland unit...

Economy overseas reproduction door perimeter seal. These glue to the perimeter of the doors and are held in by screws on both ends. Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

These are reproduction heater hose grommets for the heater hose to pass through the firewall. Most of the firewalls that we have seen have a flared opening for the hose without a grommet. Save your hoses, buy some grommets?

This is the passenger side trim / moulding that mounts to the door window and creates the seal between the door glass and the quarter window on 69 Cougars and Mustangs. Get the seal you need for this moulding here.