Daniel Carpenter / Dennis Carpenter

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

These Back Up Light Lens Gaskets are sold as a pair. Fits the 67 and the 68. Replaces Ford part # C5ZZ-15510.

The correct color for the Cougar was gray but many prefer these black Mustang gaskets. Sold as a pair.

These Back Up Light To Rear Valance Seals are Sold as a pair. Fits the 67 and the 68. Replaces Ford part #: C7ZZ-15533. Note, gray is in fact the correct color for these, Mustang used black in 67-68. Note we also have black available for those who prefer.

These pads go between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only. Sold as a pair.  Replaces Ford part #: C8WY-13493.*Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

Replaces Ford part #C8WY-15447. Sold as a pair, two required per car. Right is the same as left.

Reproduction taillight housing to body seal kit for the Mercury Cougar or Shelby Mustang. Sold as a kit for two lights. Replaces Ford part # C7WY-13520.

Sold as a pair. These seal the lens to the taillight bucket / backing plate. Also used on the 1967 Shelby. Replaces Ford part # C7WY-13461.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

This 67 and 68 Firewall To Hood Seal Reproduction has attached rubber studs for mounting. Replaces Ford Part #: C7ZZ-16740.

This Wiper Pivot To Cowl Seal Reproduction is sold as a pair. Fits both the 67 and 68. Replaces Ford part #: C5ZZ-17475.

This economy version is made from a softer composition than original and does not hold up very well on a Cougar due to the force that the actuator exerts.  Sold as a Pair. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Reproduction license plate / fuel door cover rubber bumpers for the Mercury Cougar or Ford Mustang. These will also work for the 1969-70 Mercury Cougar or Ford Mustang cowl cover to hood rubber bumpers. Sold as a pair with the mounting screws. *NOTE* These are not an exact replacement, rather a part from another year and application that has been found to be an adequate substitution. If you really need an exact replacement we sometimes can provide a used bumper. ...

Four per car, mounts to fender. Sold individually. Replaces Ford part #: C7WY-16758.

These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

For the in-dash ashtray.

Sold individually.

Comes with attaching staples made of stainless steel. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. Replaces Ford part #: C4DZ-16238.Not all cars were assembled with this seal, some came with staples, and others used clips.

Reproduction 5/16" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C5ZZ-9288.

This kit includes 33 pieces and has the quarter panel drain valves.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

Replaces Ford part #: D2WY-6543720.

These were installed only on early production 1967 Cougars but can be installed on any 1967 Cougar. Later in the year they quit installing these and just used a rubber plug to fill the hole. 1968 was not drilled for these. Sold as a pair.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...