1965 Ford Mustang

This is one of the best small block Ford V-8 books on the market. It covers 260-289-302 V8 engines. Carburetor numbers, distributor numbers, covers all engine brackets, pulleys, and parts of Ford small block engines. 100's of pages with pictures, casting numbers, and explanations by year. A must for concours detailing and year by year correctness. Author Bob Mannel, covers small block V8 engines and components 1962-69. References all Ford cars that these engines came in. Mustang, Cougar,...

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included. Ford part number C3AZ-4851-L.

Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available.  NOS power steering control valve repair kit.  Ford part number C2AZ-3A553-A.

Reproduction ring gear for 157 tooth fly wheels and flex plates as found on certain 289 and 302 engines in 1967-68 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

Beautifully detailed reproduction of the original wheel mounted on the 1965 GT-350. The aluminum center is CNC machined and set into a steel rim that features triple plate high luster chrome. Center cap sold separately.  You can find the styled wheel center caps here. Find the lug nuts here. *NOTE* Limited availability on this unit, so give us a call before you order. Please allow 4 to 5 weeks for delivery. ...

Set of reproduction Ford Top Loader 4 speed shift rods for 1967-68 Mercury Cougar or Ford Mustang with 289 or 302 engines only. 

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1967 Mercury Cougar and 1964 - 1967 Ford Mustang with 289 engines. Ford part number C5ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

This hand held cart was used by service stations or garages to hold spools or bare wire to make them easily accessible when needed. There's a handy foot long ruler painted into it to quickly and easily measure lengths of wire. The design and style suggests that it could be from anytime between 1940 and 1970, making it a valuable collectors item for car enthusiasts. Condition is used, but aside from obvious defects and patina (see photos above, random wire included),...