1966 Ford Mustang

This system features the "Original" Baer 2-piston, pad guided caliper (PGC) mounted to a 13", 1-piece slot, drill, zinc plated integral hub rotor. The PGC caliper comes in a red powder coated finish with a black logo, includes dust/weather seal's and uses the popular D412 pad type. The system includes premium bearings with races pre-installed, dust caps, mounting brackets, stainless braided hoses and all necessary hardware. The 13" "Classic" system fits select 17" or larger wheels.You can...

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

***WARNING*** Plugging these directly into a Cougar wiring harness without correctly re-wiring in the pigtails may fry your wiring harness! Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Ford Mustang. The plug is not correct for the Mercury Cougar's wiring harness and will need to be changed to work properly. However, this is an easy straightforward process which we lay out below. Plus you can save a good amount of that...

This is a single plug (standard models without low fuel warning light) fuel sending unit with an extra bung for a return line for 1967-68 Cougars and Mustangs running fuel injection. No need to change the whole tank in order to upgrade your car to fuel injection!  Main line 3/8" Return line 1/4" Check out the video below on our new gauge tester

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...

GT 350 Holley 715 CFM center pivot bowl to bowl transfer tube. This is not for a regular Holley 4150. These tube ends are about 12-1/2 inches apart. Dual quads?

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...