1966 Ford Mustang

NOS dealership novelty item that was likely handed out in the late 60's early 70's. We're not exactly sure what the purpose of this inflatable pad was, but our best guess is it could have possibly been used as a child's booster seat pad, maybe an inflatable pillow, or even a pool floatie.  Made from vinyl and measures 16"x16" when flattened out as shown.  Comes with original blow up straw. If you have any information on this item we'd love to hear from you! ...

Reproduction washer for the interlock on all top loader 4 speed transmissions as found on 1967-69 Mercury Cougar and Ford Mustangs.Ford part number C5ZZ-7C318-A.

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. Check out this video

C5ZZ-6521768-A Front bracket that mounts to the door window channel, it prevents the front section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side door.See C7ZZ-6521772-A for the rear stop bracket and bolt.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view...

Original New Old Stock NOS reverse light lenses. Sold as a pair, includes screws!Ford Part number C5ZZ-15514-A.

Used backup / reverse light for the driver side (left hand) of the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Casting number as seen on the back side reads C7ZB-15A509-A. Replaces Ford part # C7ZZ-15512.

Used backup / reverse light for the passenger side (right hand) of the the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Perfect inexpensive replacement item for those wanting to keep their car all original and match the overall patina of their low mile car. Casting number as seen on the back side reads C7ZB-15515-A.Replaces Ford part #...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang convertibles...

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561692-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

Reproduction Shelby Cobra center caps for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a black background.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. Check out our center cap installation tips video below ...