1966 Ford Mustang

These Back-Up Lamp Lenses are exact copies of the originals which come with the FoMoCo Logo. Sold Individually. Includes screws!

Great chrome on this reproduction backup / reverse light for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15512.

Great chrome on this reproduction backup / reverse light for the passenger side (right hand) of the the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15511.

This item is considered Hazmat by shippers. This item can ONLY ship via USPS Ground Advantage to the lower 48 Contiguous United States.No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part #C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar...

Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.

Set of 12 bolts for the intake manifold on any factory 1966-67 Ford 289 engine. AMK F-478.*Note - Excludes 1968 289 and 302 engines.

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate reproduction. 

Bracket mounts to 9 inch third member. Will not have heavy corrosion as found on Midwest and Eastern cars. Not notched like later years of snubbers. Correct for 1967 Mercury Cougar and 1965-67 Ford Mustang. Rubber bumper sold separately - C3AZ-4730-B rubber carrier bumper. Picture - 2007 40th Anniversary show in Carlisle PA. Bill Pratt with "Catvert".

Carburetor dash pot bracket, this is the bracket with a 'hump' and a hole. Fits all Autolite 2100, 4100, and 4300 carburetors if needed 1967-68 Mercury Cougar and 1965-68 Ford and Mustang. Some of these have a trace of Gold color on them like other carburetor parts. Small hole for attaching to left front of the carburetors, before anyone asks, we do not have the fasteners for these. Larger hole is threaded for factory installed dashpot which is 5/16-24. Some, or most carburetors likely...

Detachable mounting plate for installing the driver side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A19-A.