All Available Parts - 1969 Ford Mustang

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Used plastic sheath that covers the bolted buckle end of where your shoulder belt attaches to the roof section of your car. Sometimes when removing the bolt from your shoulder belt, this sheath will tear if the plastic has become stiffened. Although it does not affect it's usage, sometimes it's best to simply replace it.  NOTE: To remove this sheath, you will have to pull some slack from the seat belt up through the opening at the top in order to push up on the sheath to access the...

This is an example of the best set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

This is a very rare find. "Grade A" 1969 XR7 / Shelby only, crack free original lid. Grade A will exhibit minimal loss of texture and will still be pliable. Notice how the three humps stand taller and rounder than the reproduction. Limited colors on hand, please let us know which color you desire and we will try to accommodate. Pictured pad is for reference only. The 1970 version was a soft spongy material. 

Used middle console support bracket. Held in place by 2 rivets midway under the console.

Used rear console support bracket for the 69 Cougar or Mustang. Mounts under the leading edge of the storage compartment under the console.NOTE - 69 and 70 used different brackets

Used front console support bracket. Held in place by 2 phillips screws at the front, under the console. NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.

This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A

Used Two Spoke Steering Wheel Pad for the 1969 Mercury Cougar or Ford Mustang. Grade B pads will have minor scuffs and scratches and will need to be repainted. Keep in mind that the pad pictured is just a reference photo and not the actual color you will receive.  Leave a note in the comments section of your order and we will try our best to match your color.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

C6OZ-3069-A Bushing for insertion into the lower control arm of all 1967-73 Mercury Cougar and Ford Mustang, 1966-71 mid sized including Fairlane, Ranchero, Torino, Cyclone, etc. 1970 and newer Maverick/Comet. Bushing has 1/2 inch inside diameter. Sold individually.

NOS fixed column turn signal switch for the Mercury Cougar or Ford Mustang.Ford part # C9AZ-13341-R.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

C4DZ-5415-A Sold as a pair

C9ZZ-2853-A Front emergency brake cable for all 1969-70 Mercury Cougar and Ford Mustang. Front cable attaches to the emergency foot brake. New Old Stock, measures 43-5/8 inches long.

C60Z-3047-A Used on many Ford products starting with the 1966 Ford Fairlane.

C7AZ-6571-B

D4AZ-18495-A

Sold as a set of three. Fits 1969-73 Mercury Cougar and Ford Mustang.Ford part number .

C8AZ-2B296-A

C8AZ-6223362-A. Sold individually, has a different look than our reproduction decals.

Original NOS shroud with correct chocolate brown color and texture as what came on your Cougar the day it was made. The later shrouds sold by Ford were smooth, black and the "Barnum Fibre Co. Inc." maker lettering was faint. This is a wonderful piece for that concours quality 1969 BOSS 302 Eliminator or GT350 Shelby.Ford Part number C9OZ-8146-A

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

D6DZ-3A730-C

Original or NOS Ford distributor cap.

C9ZZ-7A624-A

New old stock power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch. Stamped C8AB-14529-A. This is the 1 tab switch. However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

This is our heater cable for use with Mercury Cougars and Ford Mustangs with factory equipped A/C. The best part, its NOS, so you know it will fit right the first time! Ford part # C9ZZ-19988-A.

C5ZA-2454-G or C5ZZ-2454-D New Old Stock manual transmission disc brake pedal pad with stainless steel insert as shown. Application is 1967-70 Mercury Cougar and 1965-70 Ford Mustang, 3 or 4 speed manual transmissions.

NOS windshield wiper blade assembly for the 74-78 Mercury Cougar or 74-78 Ford Mustang.  This is also listed as the service replacement for the 1969 - 1970 Cougar / Mustang.  This is a pair of Anco 16" windshield wiper blade assemblies.Ford part # D4AZ-17528-C.This part was replaced by E3DZ-17528-B.

C9ZZ-18A318-A New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang

C9AZ-15A440-A Fits many applications including Galaxie, Torino, Shelby, Marquis and Mustang,1969 only.  

D2PZ-8597-A New Old Stock service replacement. Fits 260/289/302 engines from 1966-69. The water bypass hose goes between the water pump and water neck that attaches to the intake manifold.

D0AZ-62234A24-B New Old Stock power window regulator gear replacement kit. Fits 1969-73 Mercury Cougar and 1971-73 Ford Mustang. Doors and quarter windows.

C0TZ-13A024-A

C9ZZ-17260-A New Old Stock speedometer cable. Fits 1969-70 Mercury Cougar and Ford Mustang with V-8 engines and 4 speed manual transmissions. Over all length 69 inches. *Note - Excludes 3.91 and 4.30 ring and pinion ratios with gear reducer.

C9ZZ-7210-A

[No Description Provided]

Great addition to that show quality FE powered early Cougar. Unlike the reproduction this has the original part number, BARNUM BROS. FIBRE CO. INC. lettering and FoMoCo insignia at the top driver side. This was one of the last units out the door when FORD discontinued them in the 1990's. Weighs 2.70 pounds and the reproduction weighs 1.54 pounds. Ford part number C8ZZ-8146-A

New Old Stock passenger side door ajar switch for any 1969-70 Mercury Cougar or Ford Mustang with specific option. Standard on XR7, normally part of the convenience group option. Ford part number C9WY-14018-A.

C4AZ-13564-A

New old stock instrument voltage regulator Ford part number C9AZ-10804-ACheck out our video below on how to use the new gauge tester: ...

C9ZZ-19B888-A

C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.

D5DZ-6221812-A

C9ZZ-18A318-B

NOS Ford key blank for ignition and doors.C7AZ-622053-A Sold Individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in...

Replaces Ford Part #: C6OZ-3C651-A or (service replacement for) C1AZ-3C651-A

C8AZ-14529-C

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

New old stock deluxe shifter handle in light aqua. Perfect condition, no cracks in the plastic. No release button or set screw included. NOS Ford part number C8OZ-7213-AQ The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

New old stock, NOS, windshield wiper switch for any 1969 Cougar or Mustang. Marked C9ZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than this 1969 version.

NOS ignition switch kit for any 1968-69 Mercury Cougar or Ford Mustang. Includes ignition cylinder and plug with pigtail wires. This is a new old stock Motorcraft part. Comes as shown, you will need to reuse your key lock cylinder. Ford part number D1AZ-11572-C.

This shroud was what Ford would have sold you in the later years up until they discontinued them in the late 1990's. It has the original Ford part number just like the original but is made of a different material and is black instead of dark brown.Ford part number C9OZ-8146-A

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. New Old Stock OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder. Thread pitch 1/2" x 20

NOS Ford key blank for trunk and glove box.Sold Individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but...

NOS oil pressure remote sending unit tube assembly. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge.The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell shaped oil pressure...

NOS FoMoCo part in the box. This is the rubber bellows also called the vacuum servo on many speed or cruise control units installed on many Ford products in the 1960's. Likely a component of the servo assembly as installed on 1967-69 Mercury Cougar and Ford Mustangs. Likely also could be used on 1965-71 Lincoln, Mercury or Ford cars with factory installed speed control option.Very hard part to find, the rubber deteriorates from the heat generated by the engines on these cars. Please check your...

This new old stock intermittent wiper switch has a two speed wiper function, but when turned counter clockwise, it has a rheostat that sets the different delay times. Switches can be physically marked with casting numbers of C9ZB-17A553-E, C9ZF-17A553-B or C9ZF-17A553-C. Any of which can be correct, and chances are, there are probably other casting numbers out there as well. This 69 switch has a total length of 3 3/8". A 1970 switch can be used, but the shaft is about 3/8" longer....

C9ZZ-18A318-C New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang.Tested and works perfectly. Has attached extension marked C9ZA-18A318-J.

New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.

New old stock manual steering worm gear for any 1967-70 Mercury Cougar or Ford Mustang with manual steering or 19:1 steering gear box. Factory new worm gear assembly for rebuilding your steering gear box. NOS in the box Ford part number C7ZZ-3524-C. ...

(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...

New old stock rubber fender to hood bumpers. Set of 4 NOS Ford. Replaces Ford part #: C6OZ-16758-A.

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

New old stock ashtray for any 1969-70 Mercury Cougar or Ford Mustang with factory console. This is the rear ash tray. Ford part number C8AZ-6262876-A.

New old stock stainless clutch pedal pad trim. About 1/8 inches wider that the reproduction version. Replaces Ford Part #: C9ZZ-7B544-A.

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. ...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Good reproduction but our used unit is a better value and will clean up just as nice.

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

This is an example of the best grade A set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

Are you looking to replace or upgrade your complicated 1968-70 3 Point Seat Belts with a modern easy to use factory looking Belt? These 3 Point Seat Belts will bolt onto any 1968-1970 Coupe using your existing mounting hardware... The belt buckles are very similar to the original Starburst buckles Ford used in the Late 1960's. Please keep in mind that although these are called "Parchment", they are more of a light brown / tan color. These belts are nice aesthetically, they don't fit very...

Reproduction pair of black seat belt buckle bezels for the Mercury Cougar, Ford Mustang, or Ford Torino. It is little details like these that often make the difference between first and second place at the show. 

Both deluxe and standard use the same retractor in 1968 - 1969 and left is the same design as right. Grade "A" retractors will show no fading or cracks on the holster / retractor cover, good chrome buckle and may even still have the date code tag sewn in place. For no extra charge we will attempt to locate the correct date code for your car if you provide your cars build date. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. Check out our video "All about seat...

Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available.  NOS power steering control valve repair kit.  Ford part number C2AZ-3A553-A.

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

New Old Stock NOS passenger side front turn signal assembly. Bezel, lens, housing. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13210-A, casting number C9WB-132_7.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

NOS heater cable for 1969 - 1973 Cougars or Mustangs that are not equipped with factory air conditioning.Ford Part #: D1ZZ-18518-A

C6OE-D and C7AE-F marked fans. Applications: 1. 1968 C code 289-2V engine without air conditioning or heavy duty, or 'extra cooling' option (small radiator). 2. 1969 Boss 302 Eliminator and Mustang. Mustang owners, this 4 blade fan with the part number C6OE-D and (C7AE-F for 1967 and later), is also correct for those K code 289 HiPo engines in both 1966 and 1967. Fan description - 4 blades and 17-1/8 inches in diameter. Ford master part number C6OZ-8600-D. Check out this interesting video...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

Carter manufactured valve with C8TE-9B289-B and 4490-S imprinted on the valves' cover. Another hard to find part with correct date codes specific to Boss 302. Ford part number C8TZ-9B289-A. These units are used, not tested and one should assume they are non-functional. These units are used, not tested and one should assume they are non-functional. *Note, we try to carry later manufactured 'Service replacement' Carter anti backfire valves which are in every way the same, but...

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.