All Available Parts - 1969 Ford Mustang

This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.

Installation of this bracket is easy but you will have to make a spacer to fit on the outside of the frame rail. One must use this part when installing headers with power steering. Hopefully you bought this bracket first before you tore out the nut inserts in the frame. If not you will need to get them up for now. Then tap the bracket toward the the outside of the car and make sure the cross bolt lines up. Then measure the gap and make a spacer to fit. A half inch nut and a couple of...

This cast bracket bolts to the frame on the driver side and anchors the power steering hydraulic cylinder. One of the benefits of buying parts from Western parts cars is that they have not been corroded by salt! This part comes "as taken from a parts car". At least two variations of this bracket (see photos above) between 1967-70. Our observations show the version with the curved casting number version orientation to be from 1970 Cougars with were all built in Dearborn, Michigan. The...

Bare metal power steering hose bracket for any 1967-69 small block Mercury Cougar or Ford Mustang. 289-2V, 289-4V, 302-2V, 302-4V, 351-2V, and 351-4V. No rubber insulator included.

Nut for attaching the power steering pump bracket onto the pivot stud coming out of the cylinder head. All 1967-69 Mercury Cougar and Ford Mustang engines additionally used on 1970 428CJ engines.

Reproduction power steering drop bracket for the Mercury Cougar or Ford Mustang. One must use this part when installing headers with power steering.  Because of the way this bracket hangs down, it will get bumped and bumped hard in time. Becasue of this we recommend considerning our premuim version of this bracket, as it is substantially stronger.

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.

Used original lower power steering hose mounting bracket for 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. This used version has the indexing tab which the reproduction does not. May come with new bolt and or rubber insulator.Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

Application could be for any 1967-69 Ford 289 / 302 /351W, but with only a single alternator belt. This is a copy of the Ford 7AA power steering pulley. This pulley mounted correctly on an OEM pump with factory brackets, will run on the second V-belt from the inside. The inner most fan belt runs the alternator. You would be using a single belt on the alternator. Correct application is for 1969 with 351W engines. 5-1/4" diameter and 3/8" sheave width.

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to...

Power Steering Hydraulic Oil Reservoir C9OZ-3A697-A - Used C9OZ-3A697-A Application is 1969 351 engines and Mustang with 302 or 351 engines. Originally found on pumps with a tag number of HBA-BK. Barbed low pressure line bent at 90 degrees and turned down. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to look like grade A

Grade B Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps....

Grade A Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps. Our...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have...

Power Steering Hydraulic Oil Reservoir C9OZ-3A697-A - Used C9OZ-3A697-A Application is 1969 351 engines and Mustang with 302 or 351 engines. Originally found on pumps with a tag number of HBA-BK. Barbed low pressure line bent at 90 degrees and turned down. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have some shelf wear but nothing major. If it shows out of stock please hit the "notify me" button...

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

Tag marked HBA-BK for use on 1969 Cougar and Mustang with power steering pumps originally installed on 302 or 351 engines. Various dates and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. *Note - 1969 only.

Used ashtray assembly for use in 1969 Mercury Cougar and Ford Mustang without center consoles. Pebble grain finish, you paint to match your interior color. Cigar lighter and ash tray knob not included. Illumination light socket and wiring available separately.

Under dash installed ashtray for all 1969 Mercury Cougar and Ford Mustang without console. Ashtray drawer combination only used in 1969, smaller version than the 1970 ashtray. Pebble grain finish you paint to match you interior color. Knob and bezel not included. Ashtray only.

This complete four part kit is correct for any 1969 small block 351 Windsor Mercury Cougar or Ford anything 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut. If you do not have a air conditioning you will need a the rectangular spacer which is sold separately.

This new reproduction power steering ram cylinder is good quality with almost no warranty claims. However, When you go to put your cotter pin in the castle nut you will often find it does not align perfectly which means you may have to drill it for a perfect fit. Keep in mind we will pay $30 in in-store credit for a clean original used ram cylinder so don't throw them away! RAM BOOT SOLD SEPARATELY. Replaces Ford Part #: C3DZ-3A540-A or C7ZZ-3A540-A. ...

This an original, rebuilt power steering slave / ram cylinder. It has not had a cosmetic restoration so it will show external dings, scrapes and general wear associated with a 50 year old part located on the bottom of a car. If you buy our reproduction ram do not throw away your core used ram as we often can give in store credit for the part. RAM DUST BOOT SOLD SEPARATELY.Replaces Ford Part #: C7ZZ-3A540-A.

Reproduction rubber boot for the drag link end of the power steering ram cylinder on most any 1967-70 Ford small and intermediate sized cars. Comes with band style crimp clamp like the originals. Keep in mind that this product is made from material that is thinner and softer than OEM.

Unfortunately we have had a high rate of returns due to failure on these and can no longer enthusiastically recommend them. Please consider our original rebuilt units. This is the large nut control valve that Ford switched to after 1967. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. These units are designed to use type F fluid, not off the shelf power steering fluid. Please follow the procedures for...

Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.

Used on both 351w 2V and 4V FMX transmissions in 1969. Approximately 17-1/2" long with a black color code paint daub on the end closest to the carburetor. This is not correct for any 1970 Cougar equipped with a 351 Cleveland or Windsor motor. *NOTE* Although the MPC lists this part as 1969 only it does in fact apply to the 1970 Cougars equipped with the 351 Windsor two barrel motor. Not only did Ford confuse the public by giving both the 1970 351C 2V and 351W 2V the same engine code "H" in...

According to the Master Parts Catalog, this rod was used on all 1969 Cougars equipped with a C6 transmission which includes the 390IP / 428CJ / 428SCJ. Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP / C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any other Ford product. ...

Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.

Transmission Vacuum line OE for the C6 transmission with 90 deg. bend at trans.

Manual control shift linkage assembly for a floor shift FMX transmission in any 1969 Mercury Cougar or Ford Mustang. Comes as shown.  1969 linkage is different than 1970, 1970 included a provision for the steering column lock out rod. Check out this video

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used dust and safety cover for all 69 - 73 Cougars and Mustangs with the FMX (code X) automatic transmission. Access plate for the torque converter and flex-plate.

Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....

Reproduction steel inspection cover for all 67 - 70 Cougars or Mustangs with 390, 427, or 428CJ engines with the C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.

4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

It is as nice as it looks! Good fit. Replaces Ford Part #: C9ZZ-7E271-A Customer reviews: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked it up in a manual. That's customer...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M and C5ZZ-7C488-D. Your buttons may have faded to gray after many years. These black buttons are injection molded plastic and have steel wear plates just like the originals. Technically this is a copy of the...

Tired of picking your broken button off the floor? This inserts in the left hand side of your deluxe (colored keyed) shift handle. Quality part made in China, please consider our good used units at half the price! 67 is actually a little different in contour but this will fit fine. Replaces Ford #: C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions. Shift rod approximately 17 inches long. Rod marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The early versions used the C5ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Automatic shifter dial black background. This part screws to the shifter bucket, and sits under the pointer when everything is assembled in your shifter bucket assembly. Fits all 1969-73 Mercury Cougar and Ford Mustangs with automatic transmissions. Original Ford part number C9ZZ-7A213-A also can be D1ZZ-7A213-A. Check out our video on rebuilding your shifter below: ...

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

For all 1969 and 1970 Cougars with H code 351-2V and M code 351-4V engines and FMX automatic transmissions. This part weighs 2.66 pounds and when set on a level surface the height of the mounting hole on the driver side measures 3" on center and the passenger side 3 1/8" on center. Ford part number C9ZZ-6A023-A. *NOTE* The picture with all four crossmembers in a line shows the three versions of the small block C-6 and FMX units in the foreground and the last is the big block C-6 unit. Notice...

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

This fragile little plastic arrow is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Black plastic dummy button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Ford part C8ZZ-7C488-A.

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The late versions used the C9ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Automatic shifter arm pawl - early version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1967-70 Mercury Cougar, 1965-70 Ford Mustang, and 1965-66 Ford and Mercury full size cars with floor shift automatic transmissions. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need, this early pawl has a Ford part number...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the early version with small width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-A. *Note - Chromed lever and internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the late version with wider width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-C. *Note - Chromed lever internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction of the little plastic shift indicator arrow, that is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Additionally it does not fit with the 1973 chromed T-handle without trimming.  Ford part C8ZZ-7C488-B.  Check out our video on rebuilding your shifter below: ...

1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. These are used, and because of the low grade of chrome plating, these will show some form of light pitting.  handle, which is larger and has a faux leather covered handle in a variety of colors. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1969 and most 1970 Mercury Cougar or Ford Mustang with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-A. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. C4 transmissions only, code "W" on your door data plate tag. All 302 and 6 cylinder engines received the C-4 automatic transmission. Rod with casting number C9ZA-7326-D. Shift rod approximately 17-1/4 inches long. 1969 Ford Mustang only. Check out our video on rebuilding your shifter below: ...

Reproduction adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions.Includes pin and nut. Shift rod approximately 18 inches long. Replaces Ford part number marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Reproduction console shift assembly for the 69 - 73 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm, seals and hardware. Replaces Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads.  3/8-24 threaded nut, serrated washer head style. Check out our video on rebuilding your shifter below: ...

Factory engine block spacer plate for 1969 1970 351W and 351C engines FMX (code X) and C6 (code U) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions. There are probably two versions of this plate, we believe the the 1969 version did not have the indentations. Replaces Ford part number D0AZ-7007-A.

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.

Reproduction engine block spacer plate for 1969 1970 351 engines FMX (code X) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too.  Replaces Ford part number D0AZ-7007-A.

Unlike previous reproductions this has the correct grommet that passes through the firewall.  Replaces Ford Part #: C9ZZ-17260-A.  This cable measures 58 1/2" at its very most outer ends.

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Speedometer cable that fits all 1969-73 Mercury Cougar and Ford Mustang with C-6 transmissions. This replacement cable is longer than the originals and does not have the firewall grommet. This cable measures 80" inches in length. Does not include speedometer gear, has correct style plastic clip that attaches to the back of the speedometer. Replaces Ford part # C9ZZ-17260-B, D0ZZ-17260-D, and D1ZZ-17260-G.

Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

This screw attaches the speedometer / odometer to the instrument cluster housing. Two needed per speedometer, fits all years of Cougar 1967-73. This is an 8-32 x 3/8" hex flange head machine screw with captured washer. Sold individually. 

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 351W and FMX transmission. These are sold in pairs

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

OE Steel Transmission Modulator Vacuum Line for the 1969 Mercury Cougar or Ford Mustang with a 351 Windsor and an FMX transmission.

Small Block V8 with C4 Vacuum line for 1967 - 1969 Mercury Cougar / Ford Mustang

Small Block V8 with C4 Vacuum line for 1967 - 1969 Mercury Cougar / Ford Mustang

Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.