All Available Parts - 1969 Ford Mustang

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

Reproduction pair of moulding / outer dash trim pieces for the 69 - 70Cougar or Mustang.Replaces Ford Part #C9ZZ-6504718

Used wiper switch bezel for any 1969-70 Mercury Cougar or Ford Mustang. This is a used bezel that has been inspected for pits in the chrome. This used unit will likely have one of the rear orientation tabs broken, but other than that it will be a good used part. Excellently priced, compared to the reproduction. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. Replaces Ford part #: C9ZZ-10852. ...

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Reproduction nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. Replaces Ford part number C9ZZ-11650-A .

Used dash pad clip for any 1969-70 Mercury Cougar or Ford Mustang. This clip attaches to the steel dash assembly. The lower portion of the padded dashes just above the glove box door and steering column is where they attach. We have seen anywhere from 2-4 or zero of these clips installed on 1969-70 Cougars. According to Bill Q. these clips prevent the sharp dash pad screws from coming into contact with wiring or wiring harnesses. His go-around is to only use blunt screws (without a point) for...

Reproduction glove box cable. Keep in mind that the screws included in this kit are not correct. The original screws had a shoulder near the top to allow the cable to swing freely. You can find them here.Replaces Ford part #: C9ZZ-6506008.

Correct for Mustang and Cougar without factory Air Conditioning. This has the larger sized storage compartment compared to the air conditioning version. Replaces Ford part number C9ZB-6506015.*Note - This box will not work with cars that have original air conditioning.

Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.

Glove box or glove compartment light with switch. Fits 1969 Mercury Cougar, 1969 Ford Mustang. Used switch and wiring assembly, tested and working. 1969 has a part number C9WB-14413-B on the wire. Will work on a 1970 Cougar or Mustang. The wire on the 1969 pigtail is a larger gauge than the 1970 equivalent.Fits 69 CougarFits 69 Mustang

Correct reproduction for the Mustang and Cougar without factory Air Conditioning. This has the larger sized storage compartment compared to the A/C version. However, we recommend going with our good used Glove Box Liner as it will be a better fit.

Used hinge for any 1969-70 Mercury Cougar or Ford Mustang. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint.Replaces Ford part number C9ZZ-6506050-A.

Correct reproduction for 1969 and 1970 Mustang and Cougar with factory Air Conditioning. This has the smaller sized storage compartment compared to the non air conditioning version. Replaces Ford part number C9ZB-6506015.

Reproduction glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

Used glove box catch for any 1969-73 Mercury Cougar or Ford Mustang. Ford part number C9AZ-6206064-A.

Used glove box cable. Cable only, screws sold separately. The original screws had a shoulder near the top to allow the cable to swing freely. You can find them here. and we have original used.Replaces Ford part #: C9ZZ-65060A08.

Reproduction glove box latch for the 69 - 70 Cougar or Mustang. Unlike the originals, this is a keyless latch.

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

These go into your door panel, behind the inside door release handle. High quality reproduction, no excuses! Sold individually, available only in black. Includes mounting clips. Fits all Cougar door panels 1969 - 1970. Unfortunately these are not good items to paint as constant contact will scratch. We have several sets of good used pairs in a variety of colors, contact us for availability. Replaces Ford part #: C9ZZ-65226A34-A. "Don is one of the best guys you will ever deal with in the...

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. Fits 1969-70 Mercury Cougar and Ford Mustang.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. Fits 1969-70 Mercury Cougar and Ford Mustang.

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. The white color on these has an almost grey tint, these are a good neutral color to paint to whatever color you need. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. The white color on these has an almost grey tint, these are a good neutral color to paint to whatever color you need. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost...

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do.  No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without...

Chrome and black knob just like the original.NOTE: This knob is correct for 1969. It will fit on a 1970, however the orientation of the pointer will be off. You can find a good used 70 knob here. Replaces Ford Part # : C9ZZ-17513

Used knob for wiper control switch on dash panel. Constructed of metal with chrome, may show some wear on the black painted section and flaws in the plating.Ford part number C9ZZ-17513-C.

Replaces Ford part #: c9zz-10852-w. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Replaces Ford part #: C9ZZ-10852-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Replaces Ford part #: C9AZ-11584-A.

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Reproduction Ignition Lock Cylinder Bezel Spacer for the 1969 Mercury Cougar - 1969 Ford Mustang 

Nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. These are used, and usually will have small blemishes. All will have good threads and chrome plating on the face.Ford part number C9ZZ-11650-A .

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Used cigar / cigarette lighter for the lower dash mounted ashtray unit. 1969 Mercury Cougar and Ford Mustang.

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used ignition switch bezel for any 1969 Mercury Cougar, 1969 Ford Mustang and many other 1969 Ford and Mercury cars with the ignition switches on the dash panel. Good used part, little or no imperfections in the chrome, good value compared to the reproduction. Replaces Ford part #: C9AZ-11584-A.

Plastic injection molded, chrome plated like the originals. The detail on the top is not exact to original. Sold as a pair.Replaces Ford part number C8AZ-6221850-A

Polished stainless steel with correct internal black felt anti-rattle pad. Sold as a pair.

Retainer that screws to upper rear lip near the quarter glass on all 1969-70 Mercury Cougar hardtops and 1970 Ford Mustang coupes. Ford lists this part as: Retainer - quarter trim panel rear. We see these three ways on 1969-70 Cougars: one retainer in the rear position alone, two of these retainers front and rear, and one small retainer at the rear and one large retainer at the front of the panel.

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Check out this video ...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Note that the color on these has too much gray in it and is...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

Reproduction Two Spoke Steering Wheel Horn Ring for the 1968 and 1969 Mercury Cougar. This is a very good reproduction piece. The original horn contact pieces fit nicely. This casting, while different than the 1968 version with the empty cavities is actually stronger. *NOTE* Save your old horn ring, you will need to transfer the rubber spacer and the horn contacts to this reproduction part.*CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts...

Decent used horn ring but unlike our grade "A" used horn ring this one will have very minor pitting but no open blisters in finish. Good value for your driver quality 68-69 Ford / Mercury with two spoke steering wheel.

Better quality than our reproduction for less money. Ford part number C0DZ-13807-A.

Used on two spoke steering wheels. Replaces Ford Part # C0DZ-13807-A. Although it does not "look" right it will function correctly. Those in the know will purchase our good used spring.

Horn ring contact components for the standard horn ring found on 68-69 2 spoke steering wheels. Ford part number C9AZ-13A805-B. Not as shiny as the reproduction kit but the price is less and the quality is FoMoCo original all the way. Reference photo above is the order in which the parts are installed.

Exact reproduction horn ring contact components for the standard horn ring used on two spoke steering wheels, replaces Ford part # C9AZ-13A805-B. Includes new hardware

Core wheel good only for restoration. We have a very hard time keeping these in stock due to their popularity in Australia. If you have any 1969 3 spoke rim-blow steering wheels for sale we would like to hear from you! 503-463-1130 Check out this video

Not the best fit, texture is incorrect. Guaranteed disappointment, no returns on this item please.

Good used pad available in most colors, please let us know which color you need in the comments section and we will try to accommodate. Grade B pads will be lifting at the top, be a little warped and have some missing texture where your thumbs often ride at 3 and 9 o'clock.

Perfect fit.

Pictured in black. This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Check out this video ...

Reproduction rim blow steering wheel for any 1969 Mercury Cougar or Ford Mustang, and generally any other Ford Lincoln or Mercury with tri-spoke rim blow steering without speed control. Brand new to market, black is the only color. Rim Blow Switch not included. We asked long time Cougar collector and restorer Randy Carlson to give us his honest opinion of this new to the market wheel and this is how he responded; "Be ready to cut the box to pieces to get the wheel out of the packaging. It...

New screw for attaching horn pads onto steering wheels 1968-69. 2 or 3 required, sold individually.

Please email us for color on hand, rarely do we have more than one grade A in stock. Grade A will have almost no warping or lifting issues, soft and pliable and will not need repaint. Very hard to find, one year only part.

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

This is the chromed correct die cast construction for your 1969 Cougar, 1970-73 used plastic but these will fit fine and look better than the plastic units. Great Quality. Sold individually, two required per car. Part of the XR7 package. Available on other hardtop models, part of the Courtesy Light group option. Option included, engine compartment light, trunk light, map light and these rear quarter panel lights for the back seat. Replaces Ford Part #: C4SZ-13776-B.*Trivia Dearborn built...

C9WY-13776-A Right side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

C9WY-13777-A-AGRADE Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Hardest side to find in primo condition most get dinged up from errant seatbelts. These are available in reproduction. Nice Quality!These use a 212 bulb. ...

Replaces Ford part #C1SZ-13783. Replaces burnt, cracked or missing original lenses located above the rear package tray.  Two required per car, sold individually.

C9WY-13777-A Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

These lights feature beautiful chrome bezels and bright white lenses. Mounting hardware, bulbs and sockets with pigtails are included. These were used on the XR7 and all Cougars equipped with Decor level interiors in 1969 and 1970. These are AWESOME reproductions worthy of the most exacting of restorations. You will be VERY happy with these lights. Sold as a pair. Replaces Ford Part #: C9WY-13776-A & C9WY-13777-AThese use a 212 bulb.Click on images to enlarge. ...

New Old Stock Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. These are available in reproduction. Nice Quality!Ford part number C9WY-13777-A. These use a 212 bulb.

The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages. Check out this video below where we used Kevin Marti's books extensively to decode a 1969 428 CJ Cougar

This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...

Manual on how to modify your FE big block Ford for street or strip.

This manual has loads of information for modifying the BOSS 302 Cougar / Mustang engine for off road racing. It contains part number's and other key information for upgrading the suspension and drive train. This 30 page book also explains the benefits of installing items like our one piece export brace, shock tower reinforcement plates and reinforced lower engine bay cross member. This book is not just for the hardcore racing enthusiast but anyone that is looking to reinforce their Cougar...

Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.

Reproduction BOSS 302 Chassis Modification for the Strip Track Manual. This little book is packed full of tips and tricks to make your Cat or Pony and handling MACHINE! The tips in the manual also apply to the 1967-68 Cougar or Mustang. Time to sharpen the claws on your flexxy feline!

Saves time and frustration! Shows schematic and diagrams that reveal the location and function of the many vacuum systems on Cougars.

This USB flash drive contains the complete Intermediate 5 Volume Set Shop Manual for the 1969 Mercury Cougar, Mercury Full Sized Vehicles, as well as the Ford Mustang, Fairlane, and Falcon. A must for anyone planning to work on their own car. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of the shop manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with...

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

This USB flash drive contains the complete Autolite 4300 carb information from overhauling, to diagnosis and repair. A must for anyone planning to work on their own carburetor. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of this manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with USB support), and you can plug this drive in and access all the...

These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. This listing is for the driver side only. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage.*Note - 1970-73 strut rods work equally well.

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage. This listing is for the Passenger side only. *Note - 1970-73 strut rods work equally well. ...

Nuts and bolts, associated with the installation of our used 1968-69 strut rods. 1 large and medium nut for the front, and two bolts and nuts to attach to the lower control arm.

AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969.