All Available Parts - 1969 Mercury Cougar

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

New Old Stock turn signal flasher for the 1969 Mercury Cougar and Ford Mustang GT-350/500. Turn signal flasher, not emergency flasher. Ford Part number C9WB-13350-A

This big book measures 18" x 13" x 3" and weighs 8 pounds. It's a must have if you are serious about electrical or vacuum work on the Cougar, Thunderbird, Mark III, Montego, Fairlane, Maverick, Cyclone, Bronco, F100, Torino, Mustang or other Ford products products from 1969. Condition is used and will have a few pages that have torn away from the rings. Form 7795P-69 Course 13003 and 1703

Open box 1/25 scale 1969 Cougar XR7 Street Machines model kit #6533-10E0 from the AMT ERTL company in Dyersville IA. Although the outer seal has been removed, all contents inside the box are unused. The tires are in a sandwich baggie, so someone was definitely in the box at one point. Includes detailed BOSS 429 engine with performance modifications, moveable steering wheel, vinyl tires and clear and plated parts. Decals include hood stripes with claws and a Cougar sunset mural type...

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Used 1969 Mercury pocket facts booklet which included information on color selections, safety features, model availability and interior options. Measures 7" x 3.5"

Used original Golde sunroof gear box. This box is found above the headliner on the passenger side.Golde part number 0142850 00

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

NOS spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73.  Ford part number D3FZ-1386-A. J bolt not included. ...

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561692-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

This used intermittent wiper switch has a two speed wiper function, but when turned counter clockwise, it has a rheostat that sets the different delay times. Switches can be physically marked with casting numbers of C9ZB-17A553-E, C9ZF-17A553-B or C9ZF-17A553-C. Any of which can be correct, and chances are, there are probably other casting numbers out there as well. This 69 switch has a total length of 3 3/8". A 1970 switch can be used, but the shaft is about 3/8" longer. Sometimes this...

This used conversion kit includes the controller and switch to convert your standard two speed wiper system over to delay wipers. Controller part # C9ZB-17C476Switch part # C9ZF-17A553-B

This scoop has been discontinued. The closest available scoop is the 71-73 GT Scoop (Item # 26020). Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This unit will sometimes crack at the opening....

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

Pair of reproduction license plate frames bearing the name of the the original Lincoln / Mercury dealer lot in San Jose, California.  Chrome with the city and dealer name written in/on reflective material. Sold only as a pair.

Used turn signal flasher for the 1969 Mercury CougarFord Part number C9WB-13350-A

Used original rear spoiler as taken from a 1969 Eliminator. The 69 wing was lighter and much more prone to cracks and sagging as in 1970. This one was taken from a parts car and properly stored indoors since 1991. Impossible to find in this condition. SEE ABOVE PHOTO FOR INSTALLTION MEASUREMENTS AND DIMENSIONS.Ford part number C9WY-6544206-A

Used spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73. Ford part number D3FZ-1386-A. J bolt not included. This icon means that we're looking...

Driver side seat back release catch for the 68 - 70 Cougar or Mustang.

This is a very rare option for the 1969 - 1970 Mercury Cougar, Ford Mustang, and Shelby Mustang. It utilizes a center dash AC vent to blow fresh air into the cabin. The heater box is very similar to the standard heater box / plenum but has the vacuum switch and bracket mounted to the top. As our pictures will show, we are very careful to remove every nut bolt and clip. The unit shown was taken from a 1969 xr7 convertible equipped with a 390 with only 80k miles.Click on images to enlarge. There...

This original Ford service replacement hood scoop is the same as a factory installed scoop except that it does not have the embossements for the hood grille used on the very first Ram Air Cougars (prior to September 1968) and it has extra mounting stud receptacles for use on multiple applications such as the Comet GT and the Mercury Cyclone. This version does have the reinforcing or webbing like the originals. Ford part # C9WB-16C664-C, C9GB-16C664-C, and D14B-16C664-AA. Found on the bottom. ...

Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A

Attractive reproduction of a very popular, over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7G. The XR7G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem. Of course this will look great on any 1967 - 1973 Cougar. Click on images to enlarge. ...

This is an example of the best grade A set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

Factory 15/16" sway bar for all GT-E 427-4V, 428 Cobra Jets, 428Super Cobra Jets, and Boss 302 Eliminators. Factory identified with a single 'Green' and single 'Yellow' paint stripe. We also carry the spacer plates separately. *Trivia - 1970 was the first year that a rear sway bar was available on a Cougar. A 5/8 inch rear sway bar would have been included with the competition handling package in 1970. This factory used front sway bar, does not include any mounting brackets or end link...

This is an example of the best set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

Hard to find without being faded, frayed or rusted buckle. Rarely, if ever will our used shoulder belts look this pristine as they are prone to sun fade. Sold individually, 2 required per car, hardware sold separate. Contact us for colors other than black. Check out our video "All about seat belts" below. ...

This is a complete set of Deluxe (chrome bands on buckles) safety belts removed from a 1969 hardtop minus torx bolt hardware. The set consists of two front retractors (they are not side specific) that measure 22" fully extended tip to tip, four lap belts bonded in pairs with the shoulder portion measuring 45" and the lap belt portion measuring 30" total length. The two male rear belts measure 20" and mount next to the rear interior panels and the female buckle side measures 36" fully extended....

Reproduction pair of black seat belt buckle bezels for the Mercury Cougar, Ford Mustang, or Ford Torino. It is little details like these that often make the difference between first and second place at the show. 

Both deluxe and standard use the same retractor in 1968 - 1969 and left is the same design as right. Grade "A" retractors will show no fading or cracks on the holster / retractor cover, good chrome buckle and may even still have the date code tag sewn in place. For no extra charge we will attempt to locate the correct date code for your car if you provide your cars build date. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. Check out our video "All about seat...

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

390 and 427 engines with C6 automatic transmissions. Shaft diameter 3 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory.Ford part number C8WY-4602-B Ask about slip yokes. Shipping is oversized due to length.

428CJ engines with C6 automatic transmissions. Shaft diameter 3-1/2 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

Used rear leaf spring retainer for 1967 -73 Mercury Cougar with competition handling or GT suspensions. Additionally it fits 1966-71 Mercury Comet / Montego / Cycolne, 1966-71 Ford Fairlane / Torino, all with HD or GT suspensions. Identified with a stamped number "2" on the top. The inside height is 1-29/32 or 1.91 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be...

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Replacement nozzle for the side window channel 3M bonding adhesive. After a short time

Complete driver reproduction bolt in door glass mounting kit for the 1970 Cougar or Mustang. This kit includes both front brackets and rear brackets w/ rubber backing, 2 door run guides w/ inserts, both window stops and all related hardware needed to complete installation. Door glass and door glass run are optional add-ons.This kit fits the Cougar Coupe and Convertible, as well as the Mustang Coupe, Convertible, and Fastback. * - To use this kit on a 69 you must also upgrade to the...

Used drivers side or left door window regulator for all 1969-70 Mercury Cougar and Ford Mustangs with glued in door glass. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, white plastic rollers, and captured steel bushing with clip. The regulator used on the bolt in glass, which became standard soon after the 1970 model year began, is...

1969 Mercury Cougar and Ford Mustang coupe/convertible Grade A factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Excellent used door glass with no scratches. Glue-in or bonded design, will not fit early 1970 models.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and Cougar Ford part number C9ZZ-6521400-B. *NOTE* Vertical chrome trim not include. Air...

1969 Mercury Cougar and Ford Mustang coupe/convertible Grade A factory tinted glass for the driver side door, it will have the faint green tint and be marked SUN-X. Excellent used door glass with no scratches. Glue-in or bonded design, will not fit early 1970 models.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and Cougar Ford part # C9ZZ-6521401-B. *NOTE* Vertical chrome trim not included. Air...

Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This item does not include any of the window trim so save yours for reuse. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be...

Used driver side (left hand) grade "A" clear glue in style door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass and does not include any window trim, so save your for reuse. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a...

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Comes with all hardware pictured.

Used resistance wire for the under dash harness from the tachometer through the firewall for the Mercury Cougar XR7.

Used set of assorted wiring leads with clips for making repairs at the fuse block / box for the Mercury Cougar. These are part of the 14401 main under dash wiring harness. Various colors of wires were used, this will get the repair done possibly with wire color variations.If you need a specific colored single wire lead, just give us a call and we'll do our best to accommodate you.

Used factory 3/4 inch sway bar for the FE 390 engine of 1969. This bar was factory identified with a single 'Yellow' and a single 'Blue' paint stripe. This bar is not to be confused with the Competition Handling Package sway bar which was optional on any 1969 Cougar. This factory used front sway bar does not include any mounting brackets or end link kits. Ford part # C9ZZ-5482-C.

Tall version 1" thick and can be used with performance springs to bring the car to a stock ride height. Sold as a Pair. Replaces Ford Part #: C4DZ-5415-A.

1967 - 1969 390-4V engines with 3 or 4 speed manual transmissions. 1969 - 1970 Boss 302 Eliminator 4 speeds. 1970 M-code with 3 or 4 speed manual transmissions. Shaft diameter 3 inches, length 53-1/32" measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

1968 - 1970 428CJ Drive shaft - Used All 428CJ's with 4 speed manual transmissions. Shaft diameter 3 inches, length 53 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.Ford part # C8WY-4602-A.

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

This would be for the non-competition suspension Cougars. U-Bolt length 7 inches, and threads 1-1/4 inch in length. U-Bolts include two (2) correct style attaching nuts 7/16-20 threads. This size of U-bolt seems to be the most common found on Cougars, no matter the leaf pack stack.  Ford part number C7WY-5705-A. Standard suspension U-Bolts run about 6-3/4 inches in length, see related items.

Reproduction Rear Leaf Spring Center Mount Insulator Pad for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody StyleNotesYearMercur...

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

Bracket that holds the throttle cable for the G code Boss 302 Cougar Eliminators. This is a 1970 part number, it is possible that the 1969 bracket may be either different or had a C9ZZ-9741-? part number. Will update when we verify, comments welcome. 1970 Ford part number listed as D0ZZ-9741-A.

Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. New Old Stock relay. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending...

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

Used front fender extension moulding / trim clip for the Mercury Cougar. This is the largest of the three clips required to attach the aluminum 1969 fender moulding / trim to the extension. One is used on each side at the tail (larger part) of the trim piece. This unit is for the purest. If originality is not as important to you, you can get the inexpensive reproduction here.

*NOTE*   Due to the difficulty in obtaining 69 aluminum trim we no longer sell these without first having you send us your cores.  Keep in mind we pay well for quality 69 hood lip mouldings.  Do not contact us with pretzel shaped parts, parts you have attempted to fix or flattened out parts.  We need trim parts showing only minor dings / dents, scratches and dullness.  Decent used trim part that would look good on a daily driver. This purchase requires that you...

Set of Four Reproduction Rear Leaf Spring Center Mount Insulator Pads for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody...

NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.

Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This unit is sometimes called eyebrow moulding and is a decent part that will look great on a daily driver level car. If you need new attaching clips with nuts, you can get them here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Ford Part Number C9WY-16074-A ...

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

Reproduction rocker moulding / trim end clip for the Mercury Cougar. This clip is a steel clip with a wire like the original. These units are technically for the 1969 and 1970 Cougar, but they will also work well with the 1968 rocker moulding / trim. Four of these clips were used on all 1969 Cougars except for the Sport Special which used two. The 1970 Cougar also uses two per car. Sold individually.Will work on 71-3 with modification. ...

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1969 West Coast Cougar organ donor car. We recommend a...

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - UsedAlso called a pumpkin, 3.25:1 open ratio. These 3rd members will have the fill plug and 28 splined axles.Check your door tag under "Axle".

This 3-piece blemished front trim set and a scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot, a slip on the buffer wheel... There are many reasons why we label our restored trim parts as blems. We carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to. From 10-15 feet away these look as good as our...

Used driver side (left hand) lower rocker moulding / trim for the Mercury Cougar. There is a slight difference in the contour on the ends of this piece that differentiates driver and passenger side. These will not work on a 1970 as the rear wheel opening was increased in size for the 1970 model year. These 1969 mouldings are about 79-1/4" long. These almost always have one or two holes drilled in them are dull at the front due to road debris and have multiple small dings and scrapes. Driver...

Set of four NOS vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule.NOTE: These mouldings will have some shelf wear, see photos above. If you have extra sets of cores, we would be willing to give in store credit. Ford casting numbers on backs:  Driver side C9WB-65423A19 Passenger side...

Excellent condition NOS rocker panel mouldings. These are original Ford parts made on original equipment back in the day. Sold as a pair, no hardware. Items sold will be better than the ones pictured. The rounded edges on these mouldings go towards the rear, and the flat edge goes towards the front of the car. ...

Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car.Fits: 1969 Mercury Cougar1970 Mercury Cougar

Good set of four diecast original top mouldings for both two tone paint Cougar hardtops and 1970 Cougars with a factory installed Hounds-Tooth checkered vinyl top. No broken studs, cracks, bends or chips. Originally these came painted on most cars, but in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, they came chrome plated. These mouldings will need to be re-chromed to look their best.

This is a core five piece set of front windshield mouldings for a 1969 - 1970 Mercury Cougar Or Mustang (except fastback). These trim parts need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard trim parts of that description. We do not recommend the reproduction, offshore mouldings...

Why is this right rear wheel lip so costly and difficult to find these days? Consider this... The right rear was the first to go obsolete from Ford. The right rear is the one most likely to get damaged because of it being the corner that is in the "blind spot". Remember, these early Cougars did not have RH mirrors! Lastly and maybe the most relevant is the fact that the right rear wheel is your traction tire which means more damage from flying road debris, loose tire chains and the like. It...

This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...

Driver quality complete assembly with average chrome, emblem and cracked lens.

Used wiring cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Unique to the 1968 and 1969 tilt column, fixed column version will not fit on a tilt without modification. Ford part number C8ZZ-13376-A or C8ZZ-13376-B.

Good set of four used wheel lip mouldings for your 1969 - 1970 Mercury Cougar. What is considered to be an "acceptable core" is solely at our discretion. If you are in question as to what good cores are, please send quality, in focus, close-up digital pictures to westcoast@classic-cougar.com *NOTE* Some "on the edge" cores that need extra labor can be given a partial credit.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC....

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Premium reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible. This version is also much more rigid when compared to the economy version and is not so prone to denting by applying too much pressure when installing. Clips sold separately. This premium moulding weighs 10 oz., compared to the economy deck lid moulding at 6 oz., and an original moulding at 7...

New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

New old stock tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight.  Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.co...

Used Transition cover for the 68 - 69 Cougar or Mustang tilt steering column. This cover bolts to the outer cover tube.

Used Transition cover for the 68 - 69 Cougar or Mustang tilt steering column. This cover bolts to the outer cover tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction Tilt Steering hose for the 69 Cougar or Mustang. Correct in every way, this reproduction is made to be an exact fit for your original hoses.

Used vacuum hose for the steering column release valve used in the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. Regular vacuum hose can be used to replace this hose if you are missing the original. However, it will not be correct. This nice original FoMoCo hose has the correct ribbing, stripes and comes with the firewall grommet. If you are missing this piece and you want your car to be right, this is a must have.

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529034-A.

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529035-A.

This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520934-A. *NOTE* The use of this XR7 unique trim requires the use of different...

This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520935-A. *NOTE* The use of this XR7...

Title: 1969 Mustang Part and Body Illustrations (CD-ROM)Models covered: Mustang Pages: 266Format: CD-ROM Version: v5.00Requirements: Windows (all versions), CD-ROM drive, and Adobe ReaderActivation: Activation required. Product may be activated on three (3) computers Operating System: PC Windows only (not MAC)Manufacturer: Forel Publishing Company, LLC Description: The 1969 Mustang Part & Body Illustrations manual is a comprehensive collection of detailed part and...

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...