All Available Parts - 1973 Ford Mustang

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1970-73 Mercury Cougar, Ford Mustang, and many other Ford cars.Replaces Ford part # D0OZ-3332

Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-E

Original stereo radio pigtail and plug. From a 1972-73 Mercury Cougar or Ford Mustang stereo harness. Has correct plug, wire colors and makings for the plug that connects to the factory stereo radio  *Note This is the speaker radio lead, from the speaker harness.

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions...

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

Reproduction passenger side (right hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Complete six piece window glass set for the 1971, 1972 or 1973 Mercury Cougar coupe. This is the same as our five piece kit, five pieces are CLEAR but this kit also includes a tinted and shaded new windshield for no extra shipping cost. This window glass set is for vehicles with Power or Manual Crank windows. Kit includes windshield with tinted band on top, rear window glass, drivers door glass, passenger door glass, drivers quarter window glass and passenger quarter window glass.This...

Reproduction six piece SUN-X or tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear...

Reproduction CLEAR five piece glass set for the 1971-73 Mercury Cougar coupe or Ford Mustang hard top equipped with power or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint...

Reproduction TINTED five piece glass set for the Mercury Cougar coupe equipped with either power windows or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and...

Reproduction six piece extra dark tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and...

Four piece CLEAR window glass set for the 1971, 1972 or 1973 Mercury Cougar convertible with MANUAL windows. Kit includes drivers door glass, passenger door glass, drivers quarter window glass and passenger quarter window glass.This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering...

Complete five piece window glass set for the 1971, 1972 or 1973 Mercury Cougar convertible. This is the same as our four piece kit, four pieces are CLEAR but this kit also includes a tinted and shaded new windshield for no extra shipping cost. This window glass set is for vehicles with MANUAL windows. Kit includes windshield, drivers door glass, passenger door glass, drivers quarter window glass and passenger quarter window glass.This glass does not have the faint Car-Lite markings in the...

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with manually operated windows. This set does not include any window trim so save your for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the...

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the...

Reproduction clear four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the...

Complete five piece window glass set for the 1971, 1972 or 1973 Mercury Cougar convertible. This is the same as our four piece kit, four pieces are CLEAR but this kit also includes a tinted and shaded new windshield for no extra shipping cost. This window glass set is for vehicles with POWER windows. Kit includes windshield, drivers door glass, passenger door glass, drivers quarter window glass and passenger quarter window glass.This glass does not have the faint Car-Lite markings in the...

Complete five piece window glass set for the 1971, 1972 or 1973 Mercury Cougar convertible. This is the same as our four piece kit, four pieces are TINTED but this kit also includes a tinted and shaded new windshield for no extra shipping cost. This window glass set is for vehicles with POWER windows. Kit includes windshield, drivers door glass, passenger door glass, drivers quarter window glass and passenger quarter window glass.This glass does not have the faint Car-Lite markings in the...

Complete five piece window glass set for the 1971, 1972 or 1973 Mercury Cougar convertible. This is the same as our four piece kit, four pieces are TINTED but this kit also includes a tinted and shaded new windshield for no extra shipping cost. This window glass set is for vehicles with MANUAL windows. Kit includes windshield, drivers door glass, passenger door glass, drivers quarter window glass and passenger quarter window glass.This glass does not have the faint Car-Lite markings in the...

Good used original door window regulator. Driver side with manual window crank, for any 1971-73 Mercury Cougar or Ford Mustang. Guaranteed to be in excellent working order. Ford Part #: D1ZZ-6523201-A

Good used original door window regulator. Passenger side with manual window crank, for any 1971-73 Mercury Cougar or Ford Mustang. Guaranteed to be in excellent working order. Ford Part #: D1ZZ-6523200-A

383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.

384356-S Bolt with captured washer. Mounts the two stops and is used to install the channel assembly. Five total bolts per door glass, 10 used per car. Very specific sized captured washer for distributing pressure on the glass. Click on images to enlarge. 1970 similar. ...

D0OZ-6223318-A Used 1971-73 Mercury Cougar and Ford Mustang spring for the door window regulators. Same spring used on both power window regulators and manual window regulators. *Caution - These springs have an enormous amount of stored mechanical energy when installed, please use caution when removing these springs or when removing the power window door motors. We use a large sized vise grip pliers when removing and installing.

Round plastic window stop that attaches to the front and rear door window glass on all 1971-73 Mercury Cougar and Ford Mustangs. Two per door, four needed for a complete car. Mounts to the front and rear of each door glass. Used on manual crank windows and power windows.

D1ZZ-223A58-A Lower door guide insert to prevent rattling of the window. Two of these inserts are inserted into the lower door guide after the door glass run is installed. Plastic piece that is subject to cracking. Two needed per door, item sold individually. Click on images to enlarge. ...

D1ZZ-6521546-B Used metal door run for all 1971-73 Mercury Cougar and Ford Mustangs. These years only used a single door run on each door. These are not side specific as in prior years. Fits either the passenger or driver side doors. During installation lube with white grease.

D1ZZ-6521760-A Upper door glass window stop. There are two of these that bolt inside the door. These are the 'up' position stops for those round stops that mount to the glass. Item sold individually, there are two of these per door. These have one end coated with a rubberized plastic as a cushion.

D1ZZ-6521790-A Lower window stop for the door glass on 1971-73 Mercury Cougar and Ford Mustang. Just one of these stops per door. These have one end coated with a rubberized plastic as a cushion.

D1ZZ-65222A92-B Lower guide, made of white plastic. Attaches to the door channel assembly. This is what the guide for the door run. One of these per door. *Note - This is the guide only. There are two (2) anti rattle inserts that go into each guide after the door runs are installed. Click on images to enlarge. ...

D1ZZ-6522362-A Upper guide, made of white plastic. Attaches to the door channel assembly. This is what the guide for the door run. One of these per door. Click on images to enlarge.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

Bolt kit for installing front sway bar clamps to the body for any 1969-73 Mercury Cougar or Ford Mustang. 5/16" bolts for 1969-73 cars. Starting in 1969, the bolt size was changed from 3/8" to 5/16". We stock the 3/8" bolt kits, which was standard for 1967-68 cars. See related items.

Original sway bar mount for your 1971-73 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, right and left are the same. See related items.  

Used wire set for the dash plug from the main under dash wiring harness from any 1971-73 Mercury Cougar. Wire colors may vary.

Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part #...

Used driver side (left hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521411-A.  *NOT* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in...

Used passenger side (right hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521410-A.  *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the...

Door window glass grommet or washer to protect the glass for the Mercury Cougar or Ford Mustang. These units are placed under the bolts for mounting the window stops and the channel bracket. Used on most full and mid sized Ford, Mercury, and Lincoln cars. 5 of these washers are used per each door glass. At least 2 also used per side on the rear quarter glass.Ford part # D1OZ-57270A58-A.

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the passenger side door, with crank windows. It will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Ford part number D1ZZ-6521410-B. *Note - Air...

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door, with crank windows. It will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Ford part number D1ZZ-6521410-B. *Note - Air...

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door, with crank windows. It will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part number D1ZZ-6521411-B. *Note - Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. *Note - Will...

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door, with power windows. It will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part number D1ZZ-6521410-D. *Note - Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. *Note -...

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door, with power windows. It will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part number D1ZZ-6521411-D. *Note - Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. *Note - Will...

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the passenger side door, with power windows. It will have the faint green tint and be marked SUN-X. Excellent used door glass with no scratches. Ford part number D1ZZ-6521410-D. *Note - Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. *Note - Will also fit convertible model models.*Excludes Mustang fastback and sportroof...

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - UsedAlso called a pumpkin, 3.25:1 open ratio. These 3rd members will have the fill plug and 28 splined axles.Check your door tag under "Axle".

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

D1ZZ-6522380-B Used stabilizer that attaches to the top of the door in two different places. These have a fuzzy padded piece that keeps the glass from rattling while it goes up and down on the door run. In most cases, the padded fuzzy material is worn or missing. It appears that these could be repaired with fuzzy side of velcro.

Reproduction quarter window roller for the 71 - 73 Cougar or Mustang. These rollers attach to the window channel bracket and slide up and down through the window guide.Sold individually, 2 required per side, 4 per car.

Reproduction Guide Anti-Rattle set for the 71 - 73 Cougar or Mustang. Once the door glass run is installed, these bushings are inserted into the lower door guide to prevent rattling. This plastic lower door guide bushing is subject to cracking after many years of use. This is a small but essential part of properly working windows.One set per door, two sets per car.Replaces Ford part numbers: D1ZZ-6522362 / 222A92 / 223A58

383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Shoulder harness bolt cover. This also holds seat belt buckle when it is not in use. Fits Left Hand or Right Hand side of the car. 2 required per car, sold individually. Below are some examples of originals in cars from our wrecking yard: ...

This never came on a Cougar, but it is a nice upgrade from the string that attaches your seat belt shoulder strap to the coat hanger when the shoulder strap is not in use. Fits all models except convertible. Originally, the shoulder strap connected to the bolt cover on one end, And to a string on the shoulder strap that connects it to the coat hook to keep it out of the way when not in use. This new hook slides into the track on the back of the moulding over the door, and is used instead of...

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colorssold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Please note: this is the only aftermarket shade of Aqua, which was only used on the Ford Mustang. Contact us for availibility of good used Cougar correct aqua seat belts.Sold individually

These are era-correct looking seat belts at an affordable price.  These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers

These are used hose clamps that bolt to the body and lateral A/C bracket. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available may have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, securing the hoses on most cars. Replaces Ford part number 374125-S100.

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1971-73 Mercury Cougar and Mustang. It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # D1OA-19849-AA. aka YG-27

Used A/C suction service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch 'O'-ring fitting for suction hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Used A/C discharge service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch 'O'-ring fitting for discharge hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

These reproduction convertible panels only come in black and are sold as a pair. They DO NOT have the holes cut in them for the retracting seat belts, so 72 and 73 Cougar owners will need to cut these holes. In addition, you will have to cut the holes for the ashtray and power window switch or manual window crank as well as install the snaps for the top boot. This will of course require that you have your old panels to use as a guide. These panels are not as thick as the originals and if you...

Used bracket for installing the rear interior panels on any 1971-73 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. Replaces Ford part number D1ZZ-76310A84-A. 

This is an inexpensive top that is only recommended if you car is going to be stored indoors. Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our in-depth installation video below! ...

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. This is a two-ply composite which has an outer layer of canvas-looking PVC vinyl plastic, and an inner layer of...

Good used 10 blade alternator fan.Ford Part #: DOAZ-10A310-B.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Used quarter window lower window guide stop. Made of black plastic, held on by a single bolt. Mounts to the window guide on any 1971-73 Mercury Cougar or Ford Mustang Coupe or convertible. One per side, sold individually.Replaces part # D1ZZ-6539805-A.

Used front support bracket for the air conditioning compressor assembly. Starting in 1971, Ford eliminated the idler pulley and used this bracket in it's place. Replaces part # D1AZ-2888-B.

Service replacement A/C belt tensioning pulley with new installed bearing. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc.*Note* All new bearings will have a slight bit of play in them. This is by design, by...

Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.

Fan spacer, measuring 1-1/4 inches, but referenced at 1-9/32" too. Application includes 1971 - 1973 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-20, cross reference to C8YE-8546-A spacer.Ford part # D1OA-8546-AA, Ford engineering # C8YZ-8546-A.

Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.

Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-5/8 inches. Application 1972 - 1973 Mercury Cougar and Ford Mustang with 351-4V or 351CJ, and all 1971-72 351's with air conditioning. Reference number YA-75.Ford part # D2AE-8546-AA, Ford engineering # C4AZ-8546-G.

Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.

D2OE-6312-AA Application - Q code 351 Cobra Jets with air conditioning or power steering. Triple sheave pulley, 6-9/16" and 7-13/64" in diameter. Ford Master Parts number D2OZ-6A312-A.

D0AE-6312-C For both the Cleveland and Windsor variety. Starting in 1970 Ford tried to standardize many of the engine parts. This is the "with air conditioning" pulley for all 1970 - 1971 351-2V & 351C-4V engines, and all 1972 -1973 351-2V engines. Triple sheave 6-23/32", 8.00", 8-13/32" inch diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0AZ-6A312-C. *Excludes 1972 and 1973 Q code 351CJ engines. This means all 1972 and...