All Available Parts - 1973 Mercury Cougar

Used grade "A" under dash wiring harness and fuse panel / block for the Mercury Cougar XR7 and XR7 convertible. This very clean uncut harness is not corroded on the connections or brittle from heat and is tested and ready to install.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7...

Original 1973 hardtop small block or 351 V-8 engine frame brackets. Includes one each: D3ZZ-6028 & D3ZZ-6029 engine frame brackets. These will fit directly into your 1973 Mercury Cougar Coupe or 1973 Mustang with 302 or 351 engines. *Note - Engine isolator rubber mounts are no longer available for these 1973 mounts. We suggest switching to the 1971-72 engine mount brackets and easy to source rubber mounts.*Excludes 1973 convertible Cougar and Mustang.

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Original engine frame mount brackets for all 1971 to 1973 Cougar *convertibles regardless of engine and all 1971 Cougar 429 Cobra Jets. Includes one each: D1ZZ-6028-A & D1ZZ-6029-A engine frame brackets. Visually, there are also a version where there is a double set of holes on top. *Excludes non-convertibles with 351 cubic inch engines.

Used grade "B" under dash wiring harness with fuse panel / block for the Mercury Cougar XR7 and XR7 convertible. This harness may have one or two professional repairs, it is tested and ready to install. We also have this harness in grade "A" form for those of you who simply must have the best money can buy.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in...

Used XR7 grade "B" main underhood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties.1973 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning...

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and drum brakes. This is a short style pedal is for cars with four wheel manual drum brakes and is shipped bare.Ford part # D1ZZ-2455-C.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

Used Dash to Gauge Feed Harness for the 1973 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Also bundled with the wires is the air conditioning clutch wire and carburetor solenoid wiring? Used condition, tested and working, professionally repaired, normally these are hard from engine heat. Replaces Ford Part #: 14289Check out the video below on our new gauge tester: ...

These are all new, not rebuilt, concours quality. Features authentic markings and logo. Black case only. Note: There are dozens of styles which were produced by several manufacturers. These parts represent the most common type. This is a poor quality part, we recommend it for its looks only. These have a high failure rate. Replaces Ford Part #: D2AF-11450-A.

These are all new, not rebuilt, OEM Ford quality. We recommend these over the generic version and the "concours" version. Marked with Ford D2AF-11450-AA part number, but is functionally correct for all 1967-73 Cougars. Black case as original.Replaces Ford Part #: C7AF-11450-A1 , B6AZ-11450-A , C7AZ-11450-A , D2AF-11450-A , etc

This is a good used main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Mercury Cougars with factory power windows. This is a Grade B harness that has been tested, inspected and repaired as needed. This harness will function properly, but will have some obvious repairs. We also sell a Grade A harness that will look much better for judging.Replaces Ford part number...

Power window door and main harness from a 1973 Mercury Cougar or Ford Mustang. This driver side door harness has the power window plug, door ajar plug, and stereo speaker plug. Factory harness, the extra plugs were not used if you had a standard model or AM radio. Tested and inspected and ready to install. Does not include any of the other power window harness segments, i.e. passenger side door, rear windows, or under hood segments. Switches also not included. Does not fit 1972 or earlier...

NOS master power window switch for 1973 Cougars and Mustangs. Five switch assembly - driver / passenger front and rear windows, and a master lock out switch. This is a service replacement master switch, the buttons are more rounded than the 1973 version. Still all works the same. NOS E0VY-14529-C.

Used grade "B" power window master switch bezel. One year only bezel for the Cougar. Fair used part with woodgrain appliqué in place and pitted chrome. Ford engineering # D2AB-14527-A.

Used grade "A" power window master switch bezel. One year only bezel for the Cougar. Good used part with woodgrain appliqué in place and good chrome.Ford engineering # D2AB-14527-A.

Reproduction driver side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction pair of drum brake spindles. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...

D3AZ-6758-B All steel tube that was used on 1973 H code 351-2V engines, one end inserted into the rear of the carburetor vacuum fitting (had a rubber hose connecting them 6N664) and the other end inserted into the straight end of the D3-6A664-2V PCV hose. This is a formed tube with barbed ends, it does not use clamps. *Note - Excludes 1973 Q code 351CJ engines.

D3AZ-6758-C All steel tube that was used on 1973 Q code 351-4V or 351CJ engines, one end inserted into the rear of the carburetor vacuum fitting (had a rubber hose connecting them 6N664) and the other end inserted into the straight end of the D3-6A664-4V PCV hose. This is a formed tube with barbed ends, it does not use clamps. *Note – Excludes 1973 H code 351-2V engines.

D1AZ-6788-A Metal tab that bolts to the intake manifold and has a hole for the round hose retaining ring (part number D2AZ-14A163-K). 1972-1973 all 351 engines, *Restoration Tip - These were painted Ford engine blue when the engines were painted, so paint it Dark Ford engine blue.

D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.

Used on front doors of cars produced after 10-1-71 with no factory door speakers. Ford part number D2AZ-7630322-A, casting number D3AB-6523342-AA. Very hard to find with plastic knob still intact.

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...

These four original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never...

These original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.

This NOS remote mirror came to use without a Autolite or Motorcraft box. Current offering while new and never installed does have a small manufacturers defect in the casting as shown. Found on the drivers side of standard model Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A. This mirror has the Ford casting number D1WB-17743-AA. Do...

This unique gasket is only slightly different from the driver side. The angle at the front is just a little different and notice it does not have a hole drilled for the remote mirror cable used on the driver side. This gasket was also used on the 1971 Ford Torino / Ranchero and Mercury Cyclone. This is an upgrade over the reproduction we carry for a 1969 - 1970 Cougar that has a passenger side Sport Mirror. The Ford Engineering number seen on the pad reads D1OB-17724-AA. Do you have questions...

NOS passenger side (right hand) sport mirror that is correct for the Mercury Cougar. This will also work on 1969-70 Cougar, but base height is just a little bit taller. Replaces Ford part # D1OB-17713 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

Complete Service part mirror assembly for any Cougar with the sport / bullet racing style mirror. Casting number as seen on base is D1WB-17743-B.Ford part number D1WY-17682-A

This plastic fastener is used to keep your mirror cable from interfering with the movement of your door glass. It is located at the front of the door near the top.

Used manually adjustable grade "A" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and nice chrome for your restored or nice original Cougar or Galaxie. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696.Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width:...

This used grade "A" remote mirror has chrome that looks great and the adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...

This used grade "B" remote mirror has chrome that looks shabby, adjustment wand is unbroken and working. Used on the drivers side of standard Cougars, no passenger side mate was ever offered with this mirror. Two different versions of this mirror are found on 1971-73 Mecury Cougars, either casting number D1WB-17743-AA or C9AB-17743-A will be supplied.Replaces Ford part numbers D1WB-17743-AA and C9AB-17743-A.Do you have riv-nut questions? Here are riv-nut answers! ...

Ford Casting number as seen on the bottom side is D1OB-17713-AWA. Many people misinterpret it as D10B-17713-AWA, DI0B-17713-AW or Dl0B-17713-AWA. Perfect base with no cracks or bends. Visually it is impossible to tell this part from 1970 with a D0OB-17713-AW casting number on the bottom. The Pastel Blue base is from a 1970 and the Red base from a 1971. Even when placed side by side it is hard to tell the difference. Do you have questions about installing a passenger side mirror or using...

Used manually adjustable grade "B" side view mirror for the Mercury Cougar Standard or Ford Galaxie. This ambidextrous mirror can be installed on either the passenger or driver side door. This good used mirror will have good glass and will have some pitting in the chrome as shown. Also used on various 1967-73 full sized Ford and Mercury cars. Replaces Ford part # C7AZ-17696.Dimensions: Base Hole Spacing: 5-7/8"Base Length: 6-5/8"Overall Height: 5-1/8"Mirror Width: 5-1/8"Mirror Height: 3-5/16"...

Walking cat hood emblem for the 1973 Mercury Cougar. Nice looking reproduction that has been needed for some time. Although these originally came only on Standard (non-XR-7) Cougars, some owners may find this version more attractive than the XR-7 emblem.Easily installed, this item attaches using clear silicone. ...

Ford offered the 1973 Mercury Cougar hood emblem in two versions as a service replacement part. It is very rare to find them new in the box with the chrome center hood moulding, usually they are found without the chrome. This was found at the Spring 2007 Ford Carlisle show. Once its gone I doubt we will see another anytime soon. Keep in mind we are always looking for Texaco gas station memorabilia for trades! At this point we are mostly looking for poor condition signs. Will consider good...

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

This used driver side (left hand) mirror pad / gasket for use with a standard manual adjust chrome mirror. This unit will not work with a painted sport mirror or any remote mirror. Ford Engineering # imprinted on pad is C7OB-17C701-AA or C8OB-17C701-A. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a...

Inside door handle release mechanism for the driver side on base model standard 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the base door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with detachable armrests, instead of the molded armrests on the door panels, as found on the XR7 and Decor...

This was an adhesive emblem and has long since fallen off most cars or was removed when the car was painted. We often times have driver quality emblems available, but be aware, they will have some pitting issues.Our reproduction 67-68 pillar emblem is a good substitute.Original Ford part number D1WY-6542532-A.

This is one of the smallest "Cougar" emblems ever put on a Mercury Cougar. Only the 70-73 two spoke cat and xr7-G shift handle Cougar was smaller. It is also the most delicate! Very unusual to find the tail and all limbs intact on this fragile little kitty. Silver spray paint will make this cat look new again, they did not have a chrome finish from the factory. Now that we have reproduced this emblem there is little incentive to purchase this over-priced used emblem.

Found on the C pillars of a 1971 - 1973 Mercury Cougar XR7 Coupe. We rarely get good used examples of these emblems as they are always badly faded. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.

This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. We rarely have an emblem this nice in stock for more than a few weeks of any one year as the tail was prone to breaking off as well as the "cats" other limbs. We do not list these hard to find parts here to...

This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. The tail will always be broken and probably at least one leg is missing on this grade B part. While not an exact fit our 3 spoke wheel emblem cat will fit on this black background.

For 1971-73 Mercury Cougars and Ford Mustangs with the 351W engine manufactured after 10-26-1970. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Ford part # D1OA-2981-A. May also have part numbers D1OA-2981-AA, D1OA-2981-A1A, D1OA-2981-A1B, D1OA-2981-A2A, and D1OA-2981-A2B.

This is the correct emblem that came in the center of the hood moulding on a 1973 XR7 model Mercury Cougar. The price is absolutely ridiculous, I agree. Years ago when they sold for $250 I thought THAT was insane! Replaces Ford part # D3WY-16637-B.

Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

351C VALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1970-1973 Mercury Cougar and Ford Mustang with 351C engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2SZ-6582-A & D2SZ-6582-B. Although we have more of these in inventory, we do not recommend them because the remaining quantities will be less than desireable. *Note - This cover will not work on a 351 Windsor engine. ...

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969-1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall.

This cap is an exact reproduction of the original. Feature includes the AUTOLITE logo. The PCV elbow is included but not installed.Fits the 1971-73 Mercury Cougar, Ford Mustang, and most all other V8 Fords in that year range.Replaces Ford part number D1ZZ-6766-A.

This cap is an exact reproduction of the original. Feature includes the AUTOLITE logo. The PCV elbow is included but not installed.Fits the 1971-73 Mercury Cougar, Ford Mustang, and most all other V8 Fords in that year range.Replaces Ford part number D1ZZ-6766-C.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Replaces Ford Part # C8AZ-2B164-A Sold individually

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

Used seat belt bolt washer for the Mercury or Ford.

Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A

A nice reproduction oil pan in Chrome finish for the 351C. Replaces Ford Part #: D0ZZ-6675.

The oil filter made by the original Ford supplier.

Rubber oil pan gasket for the 351 Cleveland engine in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

NOS (New Old Stock) rear pancake motor for the rear quarter windows of the Mercury Cougar or Ford Mustang. These motors are often ruined because water has leaked down into the quarter panel where it has then seeped into the motor. Once water gets inside the case, the motor's days are numbered. This is because the interior of the case will eventually start to rust and it will seize the motor. This motor is a service replacement part and it would have been the motor your local dealership would...

Used passenger side (right hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with power windows. *NOTE* If your also having some issues with your rear pancake window motor, check out our video below. It will take you through the pancake motor refurbishing process. If we can do it, there is no reason why you can't too! ...

Reproduction mounting bracket. This is the mounting plate for the end links on the factory rear sway. Mercury Cougar 1970-73 only, this is not a Mustang part. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very...

Limited slip nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch cases from 1967-1973 with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit came in Cougars and...

These are the U-shaped brackets that hold the round part of the rear sway bar. These mount to the rear frame rail. All 1970 - 1973 Cougars should have these mounting holes from the factory, 1969 and earlier Cougars do not have these holes. Two clamps needed for installation.

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. All 351C engines, 351-2V and 351-4V. Fits any 1972-73 Mercury Cougar or Ford Mustang with original H or Q code 351C engines. The earlier bracket found on the 1971-72 cars will also work and is stamped slightly differently.Replaces Ford part number D2AZ-9728-A.

This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...

Rear driver side wheel lip moulding. Fits any 1971-73 Mercury Cougar.Replaces Ford part number D1WY-6529165-A.

Restored passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Restored driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weather strip. Shipping...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core passenger vinyl half roof trim. Call...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core driver vinyl half roof trim. Call 503-463-1130...

Front passenger side wheel lip moulding for any 1971-73 Mercury Cougar.Replaces Ford part number D1WY-16038-A.

REQUIRES sending your cores in advance.This is a restored aluminum 3 piece trim set from an early 1971 Mercury Cougar. Included are rear of hood trim Ford part # D1ZZ-16B918-A. Both fender trim pieces Replaces Ford part number D1WY-16C133-A and D1WY-16C132-A. Our restored aluminum trim is correctly bright dipped or anodized like originals.Technically these trim pieces were only used during the first 6 months of production on 1971 Mercury Cougar and all XR7 models including...

Left side factory aluminum door guard.

Used rubber bumper for the tilt column. 70 - 73 tilt columns require 3 bumpers, one on the lower and two on the upper knuckles. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth.  Replaces Ford part # D0AZ-3B661-A. *NOTE*...

This extension holds the inner spring tube in place on the 70 - 73 tilt column. Fragile piece, should take great care when tapping on this pot metal piece. Limited supply. Ford casting number: D0ZA-3790-*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Ford part number 3E629. Molded rubber construction, fixed and tilt steering columns. These may have been used as early as late 1972, not sure. Limited stock. The reproduction plastic version for 1969-72 will also fit and work in conjunction with the available foam insulation. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

1973 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or function, and will be in stock more often than our full priced 1973 tilt column. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

Ignition housing / cover for the fixed steering column on 71 - 73 Cougars and Mustangs. Technically called a "Flange", the ignition cylinder sits inside this cover.This item will need to be re-painted to match your column.Ford Part number D0AA-3511-CW

This is the spring that returns the actuator from the start position.

Steering column locking gear. For all 1970-73 Ford and Mercury steering columns. Made of brass, has 8 teeth and is 7/16 inches thick. Fits fixed and tilt steering columns. Ford part number D0AZ-3E717-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

1973 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt column specialist. If you do not currently have a tilt column do know you will get every part needed to make the conversion.  Often times we are unable to stock 1971-73 tilt columns due to not having tilt rag joints. We now offer a reduced...

This part is located in the left front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L09-A