All Available Parts - 1973 Mercury Cougar

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

This is a complete shaft. Lower, upper and knuckle. This shaft may have plastic pins broken due to age and handling. It is functional. May have light rust and knuckle will have been tightened if needed.

Used lower steering column shaft for 70 - 73 Cougars and Mustangs with a fixed column. Identified by length, and the round style lower flange. 1968-69 lower flange is slightly smaller with flat sides. Overall length is 16-3/8 inches.

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3676-A.

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

Used flat headed stove bolt and nut, for attaching the two steering column mounting brackets together. Brackets for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Two needed per installation, sold individually. This is a 3/8-16 square neck bolt and nut. Ford part number 384527-S2.

Used lower steering column mounting bracket at firewall, for any 1971-73 Mercury Cougar or Ford Mustang. Rubber seal will need to be replaced, see related items for rubber seal.  Ford part number D1ZZ-65017A50-A.

Correct nut that is designed not to come undone.

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

This is the brass piece that connects the keylock to the ignition switch.

Reproduction Chrome / Black Leather steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Used locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth. These units will be mint with no broken or chipped teeth....

Used lower steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column and can be the issue when you have a sloppy feeling tilt column. The hard steel pin will often waller out the soft cast metal and cause play in the column. Ford part # D1AZ-3D651-A, casting number D1AA-3D651-AA or D0AA-3508-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

Used upper steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column. Ford casting # D1AZ-3511-AWA.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the tilt steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the fixed steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...

This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Ford part number D0AA-3E715-D

Locking pawl pin for your 70 - 79 tilt steering column for all Lincoln - Mercury - Ford products. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to your locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to this part can avoid several hundred dollars in damage. This precision...

If you do not have cores that are worthy of restoration, give us a call prior to ordering, we can help! This trim set includes all the window and door moulding / trim for a hardtop 71-73 Cougar. The only two window related trim parts not included are the two horizontal trim pieces that attach to the top of the door on the XR7. We do have those trim parts listed separately. As shown you will get all six trim parts that surround the door glass and quarter windows, all four rear window trim parts...

Restored passenger side (right hand) door moulding / trim that is attached to the top of the door on the Mercury Cougar XR7. This unit is made of anodized aluminum and came on the convertible XR7 as well. Also makes a nice appearance upgrade for the standard Cougar!Ford part # D1WY-6520934-A.*NOTE* If you choose to upgrade your standard Cougar with this XR7 unique piece, it will require the use of different beltline weatherstrips. Your standard beltline weatherstrips will not work with this...

Used core grade rocker moulding for the passenger side (right hand) of any 1971-73 Mercury Cougar. Right is the same as left on the 1971-73 Rocker Mouldings, we suggest you choose between passenger and drivers side when ordering as they are always duller up front from the tires throwing up road debris. They will come with minor dents and or scrapes, but no major dents or extra holes drilled. These are driver or core quality and are good for restoration, not show quality. Ships bare, without...

Restored driver side (left hand) 1973 Mercury Cougar taillight bezel. These have been restored with the correct bright dipped, anodize finish. You will have to do the finish, detail painting. Note that in the buffing process the ridges are worn down noticeably on the horizontal bars. Mercury part number D3WY-13489-B. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a used or core D3WY-13489-B trim. Call 503-463-1130 if you have any...

Restored passenger side (right hand) 1973 Mercury Cougar taillight bezel. These have been restored with the correct bright dipped, anodize finish. You will have to do the finish, detail painting. Note that in the buffing process the ridges are worn down noticeably on the horizontal bars. Mercury part number D3WY-13489-A. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a used or core D3WY-13489-A trim. Call 503-463-1130 if you have any...

Restored driver side (left hand) quarter window moulding / trim for the Mercury Cougar. These are correct for the coupe only. Correctly restored and re-anodized. 

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. These have been restored with the correct bright dipped, anodize finish. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a core driver vinyl half roof trim. Call...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. These have been restored with the correct bright dipped, anodize finish. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a core passenger vinyl half roof trim. Call...

Anodized aluminum top of door trim for 1971-73 Mercury Cougar XR7 models, including convertible. Ford part number D1WY-6520935-A. This driver side, trim was used on the XR7 model but is a nice upgrade for a standard Cougar. Sold separately and the price includes a $45 returnable core fee.*NOTE* The use of this XR7 unique trim requires the use of different belt-line weather strips than that of the standard, models. See drivers side trim also.Due to the difficulty in obtaining trim we no longer...

Used core half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Core trim does not require an exchange, this trim will have wear, weathering, and minor dings or distortion.

Used core half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Core trim does not require an exchange, this trim will have wear, weathering, and minor dings or distortion.

Used passenger side 1973 Mercury Cougar tail light bezel. Minor blemishes, perfect driver quality. Mercury part # D3WY-13489-A. No Core required. Thinking about adding some LED taillight bulbs to your car? Here is great little video that shows the performance of LEDs and traditional bulbs side by side so that you can make an informed decision. ...

Used driver side 1973 Mercury Cougar tail light bezel. Minor blemishes, perfect driver quality. Mercury part number D3WY-13489-B. No Core required. Thinking about adding some LED taillight bulbs to your car? Here is great little video that shows the performance of LEDs and traditional bulbs side by side so that you can make an informed decision. ...

Used core grade rocker moulding for the driver side (left hand) of any 1971-73 Mercury Cougar. Right is the same as left on the 1971-73 Rocker Mouldings, we suggest you choose between passenger and drivers side when ordering as they are always duller up front from the tires throwing up road debris. They will come with minor dents and or scrapes, but no major dents or extra holes drilled. These are driver or core quality and are good for restoration, not show quality. Ships bare, without...

Used driver side (left hand) top of door moulding / trim for the Mercury Cougar XR7 coupe and convertible. Please note, these used pieces will have scratches and a general dullness due to their soft aluminum construction. This unit was used on the XR7 model, but is a nice upgrade for a standard Cougar.Ford part # D1WY-6520935-A.*NOTE* If you decide to add this moulding / trim to your standard Cat, you will also need to use the XR7 beltline weatherstripping kit. You can get the coupe...

Used passenger side (right hand) top of door moulding / trim for the Mercury Cougar XR7 coupe and convertible. Please note, these used pieces will have scratches and a general dullness due to their soft aluminum construction. This unit was used on the XR7 model, but is a nice upgrade for a standard Cougar. Ford part # D1WY-6520934-A.*NOTE* To use this XR7 unique trim, you will be required to use of XR7 beltline weatherstriping. You can get the coupe beltline kit here or...

Used passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weatherstripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item...

Used driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weatherstripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5392. Shipping...

Used, driver side, front lower, aluminum channel section, for installing the roof side or upper door and quarter window weatherstripping. Right and left sides are contoured differently, for the 1971-73 Mercury Cougar and Ford Mustang coupe and convertibles. These channels also have pre-drilled holes for installation, often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip. Piece...

Used, passenger side, front lower, aluminum channel section, for installing the roof side or upper door and quarter window weatherstripping. Right and left sides are contoured differently, for the 1971-73 Mercury Cougar and Ford Mustang coupe and convertibles. These channels also have pre-drilled holes for installation, often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Restored passenger side (right hand) quarter window moulding / trim for the XR7 Mercury Cougar. These are correct for the coupe only. Correctly restored and re-anodized.

Used passenger side (right hand) grade B vertical glass trim for the window glass of the Mercury Cougar or Ford Mustang both coupe and convertible. This stainless steel trim will have light scuffing or scratches, primarily on the outside surface. Plan on purchasing new rubber weather stripping. Will not fit Mustang fastback (Sport Roof) models.Ford part # D1ZZ-6529952-A.

Restored 6 piece vinyl top moulding / trim set for the Mercury Cougar equipped with the full vinyl top. You could have gotten your 1971-3 Cougar with either a full or half vinyl top and the moulding trim set for each is very different. This full top set has 6 pieces where the half top set is only 2 pieces. While this moulding / trim is restored, you will need to paint the detail stripe semi-gloss black yourself.  *RESTORATION TIP* You will need a can of good quality semi-gloss black...

New pan head screws for installing the tail light bezel on any 1971-73 Mercury Cougar. Sold individually, a total of 16 are used to install the brake light bezels (8 per side). #8 black pan head Phillips screw 1-1/2 inches long. Replaces Ford part number 56001-S.

Used driver side, front drip rail moulding for any 1971-73 Mercury Cougar hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the A pillar front piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and badly scratched core grade trim parts...

Used passenger side, front drip rail moulding for any 1971-73 Mercury Cougar hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the A pillar front piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and badly scratched core grade trim...

Used driver side, top drip rail moulding for any 1971-73 Mercury Cougar hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the horizontal piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and badly scratched core grade trim parts get...

Used passenger side, top drip rail moulding for any 1971-73 Mercury Cougar hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the horizontal piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and badly scratched core grade trim parts...

Used passenger side, rear XR7 drip rail moulding for any 1971-73 Mercury Cougar XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and badly...

Used driver side, rear XR7 drip rail moulding for any 1971-73 Mercury Cougar XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and badly scratched core...

Used passenger side, rear Standard model drip rail moulding for any 1971-73 Mercury Cougar NON-XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and...

Used driver side, rear Standard model drip rail moulding for any 1971-73 Mercury Cougar NON-XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Bear in mind that these parts are made from aluminum and were originally anodized to give the polished stainless steel look. Very prone to scratches and dents. This part will be 'driver quality used'. Dented and...

If you do not have cores that are worthy of restoration, give us a call prior to ordering, we can help! This trim set includes all the window and door moulding / trim for a hardtop 71-73 Cougar. As shown you will get all six trim parts that surround the door glass and quarter windows, all four rear window trim parts and both "L" shaped trim parts that surround the windshield. The difference between the Standard and XR7 sets are the quarter mouldings are smaller on the Standard version,...

Restored driver side, rear XR7 drip rail moulding for any 1971-73 Mercury Cougar XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Correctly anodized to give the polished stainless steel look. Very prone to scratches and dents.  Ford part number D1WY-6551729-B or D1WB-6551621-AE.

Restored passenger side, rear XR7 drip rail moulding for any 1971-73 Mercury Cougar XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Correctly anodized to give the polished stainless steel look. Very prone to scratches and dents. Ford part number D1WY-6551728-B or D1WB-6551620-AE.

Restored driver side, rear Standard model drip rail moulding for any 1971-73 Mercury Cougar NON-XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Correctly anodized to give the polished stainless steel look. Very prone to scratches and dents. Ford part number D1WY-6551729-A or D1WB-6551621-BC.

Restored passenger side, rear Standard model drip rail moulding for any 1971-73 Mercury Cougar NON-XR-7 hard top Coupe. A total of 3 pieces per side slip together to form the entire drip rail system on a 1971-73 Cougar. This is only the rear quarter window piece by itself. Correctly anodized to give the polished stainless steel look. Very prone to scratches and dents.  Ford part number D1WY-6551728-A or D1WB-6551620-BC.

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the small passenger side rear, about 6-7 inches in overall length. Ford casting number D1WB-65550416-AE. Ford part number D1WY-65423A18-C. No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the small driver side rear, about 6-7 inches in overall length. Ford casting number D1WB-65550416-AA part number D1WY-65423A19-C.  No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the horizontal passenger side, about 38 inches in overall length. Ford part number D1WY-65423A18-C. No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the horizontal driver side, about 38 inches in overall length. Ford part number D1WY-65423A19-C. No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the larger curved rear passenger side, about 47 inches in overall length. Ford part number D1WY-655517A36. No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the larger curved rear driver side, about 47 inches in overall length. Ford part number D1WY-655517A37. No core charge required. 

New Old Stock vinyl top moulding from any 1971-73 Mercury Cougar. This is the small driver side rear, about 6-7 inches in overall length. Ford casting number D1WB-65550416-AA part number D1WY-65423A19-C.   

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes, will not lineup with factory holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

Front driver side wheel lip moulding. Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. These pieces are also an excellent option for those of you who like to restore your parts yourself.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC. Why do we require cores be sent...

Rear passenger side wheel lip moulding. Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. These pieces are also an excellent option for those of you who like to restore your parts yourself. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Click on images...

Front passenger side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Click on images to enlarge. ...

Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. These pieces are also an excellent option for those of you who like to restore your parts yourself.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Click on images to enlarge. ...

This set of four wheel lip moldings is sold on an exchange basis. We would require your cores be in hand before we ship restored mouldings. If you have extra cores you would like to sell then we would like to hear from you! Please do not send heavily damaged trim parts as the finished product will be delicately thin. Extra screw holes and elongated holes are OK but you will be getting a like product in exchange. We are happy to send your cores in for restoration and make sure you get your...

Front driver side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores.

Front passenger side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores. Do you have questions about your cores trim pieces? This video should help! ...

Rear driver side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores. ...

Rear passenger side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores.

Restored four piece aluminum rear window moulding / trim set correctly restored with an anodized and a bright dip finish and polished to a very high luster.Ford part #s D1ZZ-6542405-A, D1ZZ-6542404-A, D1ZZ-6542430-A, D1ZZ-6542431-A.

Good used four piece aluminum rear window moulding / trim set with some dings and or minor scratches. Ready to install on your Cougar as is, or polish them to be installed on a daily driver. These original FoMoCo mouldings are far superior to the off shore reproductions that do not fit well and have an incorrect color to them. Ford part #s D1ZZ-6542405-A driver side (left hand) lower, D1ZZ-6542404-A passenger side (right hand) lower, D1ZZ-6542430-A passenger side upper, and D1ZZ-6542431-A...

Our used passenger (right hand) side upper rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A.

Our used passenger (right hand) side lower rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542404-A.

Our used driver (left hand) upper rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A. ...

Our used driver (left hand) lower rear aluminum window mouldings / trim will have light scratches and minor dings. These are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part # D1ZZ-6542430-A.