All Available Parts - 1973 Mercury Cougar

Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

Rod used for locking the FMX transmission in "Park". Connects to the lower tab of the steering column and the FMX transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a yellow mark. Casting number stamped on rod - D1ZA-7E330-AA. The FMX, automatic transmission, was used on all 1971 - 1973 Cougars with the 351-2V engine (Letter "H" in the 5th position of your VIN). Transmission...

Rod used for locking the C-6 transmission in "Park". Connects to the lower tab of the steering column and the C-6 transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a red paint mark or daub. Casting number stamped on the rod - D1ZA-7E330-BA. The C-6, automatic transmission, could be ordered with any engine from 1971 - 1973. Transmission code "U" on your door data tag.

Restored chrome automatic shifter lever for some 1970 Mercury Cougar or Ford Mustang, and all 1971-73 Cougar and Mustangs, with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found on all 1973 Mercury Cougar or Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little more ergonomic in design, compared to earlier designs. Core charge applies.Replaces Ford part number D3OZ-7213-A.

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

Black plastic selector button for all 1973 Mercury Cougar and Ford Mustang with automatic transmission. It does not fit with the 1968-72 chromed T-handle.  Check out our video on rebuilding your shifter below: ...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Reproduction console shift assembly for the 69 - 73 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm, seals and hardware. Replaces Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.

Formed metal clip that holds the gear end into any transmission. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Original dipstick tube originally painted blue and approximately 19-29/32" inches long. Application 1973 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. Ford master part number D3ZZ-7A228-B.

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

New manufactured transmission yoke for a T-5 5 speed transmission.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

Correct for 1971, 1972 and 1973 only. 351-2V and 351-4V engines , including Boss 351 for 1971 - 73. Ford part number D1TZ-6392-A and D1TZ-6392-C. Shipped bare, no hardware or clutch fork.

Reproduction bolts and washers for the manual transmission bell housing on any 1969 - 73 Cougar or Mustang equipped with a 302 / 351 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1969-73.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

These clutch pedals feature an improved design (removable pin) for easier installation. Compatible with existing hanger assembly even in automatics. Replaces Ford Part # D1ZZ-7519-B.

D1ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-C 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-A 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-B 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-D 20 Tooth Gear Pictured

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.

Very good quality replacement speedometer cables. 76 inches Replaces Ford Part # : C9ZZ-17260-B

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.

C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...

Reproduction chrome center cap with black background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap...

Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good!  When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...

Reproduction chrome center cap with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. These will work with multiple brands / styles of after market wheels as well. Sold individually.  When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...

This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

Reproduction 15x7" Eliminator wheel with a black center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This black 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need a...

Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...

Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.  These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.  NOTE! These wheels are intended to be...

New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New Legendary Series 15x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Satin Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

ETA FOR THIS ITEM IS 12/14/23Reproduction Scott Drake 16x8" Satin Black Magnum 500 wheel for your Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant but it holds up great year after year. You may save a few dollars buying the other brands out there but why? We sell these wheels with a 4 1/2" backspace unless you specify otherwise. We now have Magnum 500 caps that feature the...

New Legendary Series 15x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Charcoal Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. We also have center caps for these wheels that feature the Mercury man or the walking cat logo. Center caps and lug nuts sold separately. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we...

New Legendary Series 15x7" Stealth Black Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these...

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

Reproduction chrome center cap with a black background and chrome Walking Cat logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Chrome center cap with Red background and chrome Walking Cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer...

Reproduction chrome center cap with a black background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* *NOTE* When installing these die cast center caps, keep in mind over tightening...

Reproduction chrome center cap with a red background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate...

Reproduction chrome center cap with a blue background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Reproduction chrome spinner cap for the Mercury or Ford that is equipped with Magnum 500 wheels. This cap will also work with any Ford, GM or Mopar Magnum 500 wheel. With a mounting system that is far superior to the original, this unit will definitely give your ride a more aggressive look. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which...

Plastic Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good! Replaces Ford Part # D0OZ-1130-F.

Reproduction chrome spinner center cap for the Mercury Cougar equipped with the magnum 500 wheel. Actually, this unit will work on any Ford, GM or Mopar Magnum wheel. Looks great and the mounting system is far superior to the originals. These look really aggressive.*NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which you can get right here. ...

Set of 4 Chrome center caps with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. Fits the following models with Magnum 500 wheels: 1969 Mercury Cougar 1970 Mercury Cougar These will work with multiple brands / styles of after market wheels as well. Sold individually. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain...

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

The price you see is a temporary price reduction due to overstock. Set of 4 Chrome center caps with black background and chrome Mercury Man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and...

Set of 4 Chrome center caps with Red background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Used 14x7" styled steel wheel for your Mercury Cougar. This painted Kelsey Hayes wheel used with small cap and brushed finish trim ring that are sold separate. Cap and lugs are sold separately. Total width is 8" with a backspacing of 4".Ford part # D0ZZ-1007-C.

Used steel lateral support brace for Cougars and Mustangs with the 351-2V or 351-4V engines after 4/27/1971. Replaces part # D1AZ-2888-A.

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Air conditioning belt tensioning pulley with new bearing. This adjustable bracket and pulley was used on all 1970-73 351 engines that came with A/C, as well as 1970 428CJ & 1971 429CJ. This part often has a casting number of D0AA-8A617-C1 but not always. This adjustable idler pulley is identified by having the large bearing pulley. Same as the C8AZ-8678-A adjustable idler pulley only with a small bearing pulley. We also offer a bearing replacement service to rebuild your adjustable idler...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. Correct dimensions and easy to install. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

This is a complete working assembly with outer housing. Fits driver and passenger side dash outlets, on any 1971-73 Mercury Cougar or Ford Mustang. We sell the louvers individually if your assembly is not broken and all you lack is a couple of missing fins. The fins are easily replaced as they just snap in place. The vent housing has a Ford casting number or D1ZA-6501820. Fits both the right and left sides of the dash. Center vent is different.Ford part # D1ZZ-18C366-A.

Each vent has only one of these louvers with the protruding knob.

Here is our used vent louver for your Mercury Cougar or Ford Mustang.

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on your Mercury Cougar or Ford Mustang. Good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit.Ford part # D1ZZ-19986-A.

Complete heater and A/C control assembly includes bezel or face plate, bracket control mounting plate, electrical and plastic vacuum switches. Functional, driver quality, heater control assembly. This unit is for 1972-73 Cougars and Mustangs produced after 1-3-1972. The prior years 1971-72 assembly without the plastic vacuum switch assembly will fully interchange with this unit. Knobs and light socket wiring harness not included. Ford part # D2ZZ-19980-A. *RESTORATION TIP* If you like to...

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a grade "A" unit with no issues other than some discoloration.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield.Ford part # D1ZZ-18490-B.

Used air conditioning connecting duct or manifold. This plastic manifold mounts behind the center dash vent. Ford calls it a 'duct and connecting assembly' or 'A/C junction'. Grade 'A' condition, ships without cracks, splits, or broken tabs. Original factory or 'integral' air conditioning part.Ford part number D1ZZ-19C932-A.

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars with factor air conditioning. Cars with only the heater option used a different bezel that has a hole for the vent cable. This bezel is blank, and only has the rectangular hole for the air conditioning vent register.Replaces Ford part number D1WB-65044A13-BC (cast on the part) or D1WY-6504393-B

New clear plastic lens or face plate for the air conditioning control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to...

New clear plastic lens or face plate for the air conditioning control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

Used elbow or connector for the driver side air conditioning register. This connects the duct tube to the louvered vent. Only fits 1971-73 Mercury Cougars.Replaces Ford part number D1WY-19C692-A.

Used passenger side air conditioning duct for any 1971-73 Mercury Cougar or Ford Mustang with factory or integral A/C. Connects the center manifold to the passenger side elbow or connector.Replaces Ford part number D1ZZ-19B680-A or D1ZA-19C735-AB.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.