All Available Parts - 1972 Mercury Cougar

C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

Reproduction chrome center cap with a black background and chrome Walking Cat logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Chrome center cap with Red background and chrome Walking Cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer...

Reproduction chrome center cap with a black background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* *NOTE* When installing these die cast center caps, keep in mind over tightening...

Reproduction chrome center cap with a red background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate...

Reproduction chrome center cap with a blue background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Reproduction chrome spinner cap for the Mercury or Ford that is equipped with Magnum 500 wheels. This cap will also work with any Ford, GM or Mopar Magnum 500 wheel. With a mounting system that is far superior to the original, this unit will definitely give your ride a more aggressive look. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which...

Plastic Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good! Replaces Ford Part # D0OZ-1130-F.

Reproduction chrome spinner center cap for the Mercury Cougar equipped with the magnum 500 wheel. Actually, this unit will work on any Ford, GM or Mopar Magnum wheel. Looks great and the mounting system is far superior to the originals. These look really aggressive.*NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which you can get right here. ...

Set of 4 Chrome center caps with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. Fits the following models with Magnum 500 wheels: 1969 Mercury Cougar 1970 Mercury Cougar These will work with multiple brands / styles of after market wheels as well. Sold individually. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain...

Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

The price you see is a temporary price reduction due to overstock. Set of 4 Chrome center caps with black background and chrome Mercury Man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and...

Set of 4 Chrome center caps with Red background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Reproduction chrome center cap with black background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap...

Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good!  When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...

Reproduction chrome center cap with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. These will work with multiple brands / styles of after market wheels as well. Sold individually.  When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...

This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

Reproduction 15x7" Eliminator wheel with a black center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This black 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need a...

Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...

Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.  These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.  NOTE! These wheels are intended to be...

New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New Legendary Series 15x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Satin Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

ETA FOR THIS ITEM IS 12/14/23Reproduction Scott Drake 16x8" Satin Black Magnum 500 wheel for your Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant but it holds up great year after year. You may save a few dollars buying the other brands out there but why? We sell these wheels with a 4 1/2" backspace unless you specify otherwise. We now have Magnum 500 caps that feature the...

New Legendary Series 15x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 17x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Charcoal Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. We also have center caps for these wheels that feature the Mercury man or the walking cat logo. Center caps and lug nuts sold separately. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we...

New Legendary Series 15x7" Stealth Black Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these...

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

This is a complete working assembly with outer housing. Fits driver and passenger side dash outlets, on any 1971-73 Mercury Cougar or Ford Mustang. We sell the louvers individually if your assembly is not broken and all you lack is a couple of missing fins. The fins are easily replaced as they just snap in place. The vent housing has a Ford casting number or D1ZA-6501820. Fits both the right and left sides of the dash. Center vent is different.Ford part # D1ZZ-18C366-A.

Each vent has only one of these louvers with the protruding knob.

Here is our used vent louver for your Mercury Cougar or Ford Mustang.

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on your Mercury Cougar or Ford Mustang. Good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit.Ford part # D1ZZ-19986-A.

Complete heater and air conditioning control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly for your Mercury Cougar and Ford Mustang until 1-3-1972. Does not include the indicator light plug and harness. Ford part # D1ZZ-19A884-A. *Restoration Tip* You can purchase some plastic polish (or try toothpaste) and polish for the lens back to new. Find a silver paint pen...

Complete heater and A/C control assembly includes bezel or face plate, bracket control mounting plate, electrical and plastic vacuum switches. Functional, driver quality, heater control assembly. This unit is for 1972-73 Cougars and Mustangs produced after 1-3-1972. The prior years 1971-72 assembly without the plastic vacuum switch assembly will fully interchange with this unit. Knobs and light socket wiring harness not included. Ford part # D2ZZ-19980-A. *RESTORATION TIP* If you like to...

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a grade "A" unit with no issues other than some discoloration.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield.Ford part # D1ZZ-18490-B.

Used air conditioning connecting duct or manifold. This plastic manifold mounts behind the center dash vent. Ford calls it a 'duct and connecting assembly' or 'A/C junction'. Grade 'A' condition, ships without cracks, splits, or broken tabs. Original factory or 'integral' air conditioning part.Ford part number D1ZZ-19C932-A.

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars with factor air conditioning. Cars with only the heater option used a different bezel that has a hole for the vent cable. This bezel is blank, and only has the rectangular hole for the air conditioning vent register.Replaces Ford part number D1WB-65044A13-BC (cast on the part) or D1WY-6504393-B

New clear plastic lens or face plate for the air conditioning control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to...

New clear plastic lens or face plate for the air conditioning control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

Used elbow or connector for the driver side air conditioning register. This connects the duct tube to the louvered vent. Only fits 1971-73 Mercury Cougars.Replaces Ford part number D1WY-19C692-A.

Used passenger side air conditioning duct for any 1971-73 Mercury Cougar or Ford Mustang with factory or integral A/C. Connects the center manifold to the passenger side elbow or connector.Replaces Ford part number D1ZZ-19B680-A or D1ZA-19C735-AB.

Used steel lateral support brace for Cougars and Mustangs with the 351-2V or 351-4V engines after 4/27/1971. Replaces part # D1AZ-2888-A.

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Air conditioning belt tensioning pulley with new bearing. This adjustable bracket and pulley was used on all 1970-73 351 engines that came with A/C, as well as 1970 428CJ & 1971 429CJ. This part often has a casting number of D0AA-8A617-C1 but not always. This adjustable idler pulley is identified by having the large bearing pulley. Same as the C8AZ-8678-A adjustable idler pulley only with a small bearing pulley. We also offer a bearing replacement service to rebuild your adjustable idler...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. Correct dimensions and easy to install. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.

Reproduction aluminum wheel designed to look like the styled steel wheels that were optional in 1967 - 1970. Mercury was looking to make a wheel similar to the Cragar and Appliance brand after-market wheels available at the time so these will resemble era correct wheels on any Ford or Mopar product utilizing the 5 on 4 1/2 lug pattern. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat...

*NOTE* These Legendary wheels require being installed with Legendary lug nuts: here. Reproduction aluminum wheel designed to look like the styled steel wheels that were optional in 1967 - 1970. Mercury was looking to make a wheel similar to the Cragar and Appliance brand after-market wheels available at the time so these will resemble era correct wheels on any Ford or Mopar product utilizing the 5 on 4 1/2 lug pattern. These wheels come with free chromed plastic center caps. The caps...

Reproduction 15 x 7 aluminum alloy wheel designed to look like the styled steel wheels that were optional in 1967 - 1970. Mercury was looking to make a wheel similar to the Cragar and Appliance brand after-market wheels available at the time so these will resemble era correct wheels on any Ford or Mopar product utilizing the 5 on 4 1/2 lug pattern. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction 17 x 8 aluminum alloy wheel designed to look like the styled steel wheels that were optional in 1967 - 1970. Mercury was looking to make a wheel similar to the Cragar and Appliance brand after-market wheels available at the time so these will resemble era correct wheels on any Ford or Mopar product utilizing the 5 on 4 1/2 lug pattern. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Cast iron pedestal mount for the air conditioning compressor on all 1970 - 1973 Mercury Cougars and Ford Mustangs with the 351C engine, both the H code 351-2V and M code 351-4V engines. Ford MPC part # D0ZA-2882-C.

Used 14x7" styled steel wheel for your Mercury Cougar. This painted Kelsey Hayes wheel used with small cap and brushed finish trim ring that are sold separate. Cap and lugs are sold separately. Total width is 8" with a backspacing of 4".Ford part # D0ZZ-1007-C.

Used elbow or connector for the passenger side air conditioning register. This connects the duct tube to the louvered vent. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes with one metal clip as shown for connecting to the register vent.Replaces Ford part numberD1ZZ-19C692-A. The number from the assembly manual is D1ZA-19C677-AA.

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. 15 AMP micro switch. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.Tested and guaranteed to work, originally produced by Cherry Electrical Corp.

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "B" part and will have one defect. This part will have a crack, chip missing, etc. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Used vacuum actuator for controlling the center A/C vent on any 1971-73 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Ford part number D1ZZ-18A318-A.

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Black plastic air conditioning center vent register bezel for any 1971-73 Mercury Cougar or Ford Mustang with Factory installed or integral A/C. Mounts Horizontally in the dash panel. Individual vents roll 360 degrees to blow air straight or to the sides. For that extra level of detail, we suggest using a silver paint pen for detailing the silver edges. Ford part number D1ZZ-19893-A.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD

Machine hex bolt for installing the heater cables to the climate controls on any 1969-73 Mercury Cougar or Ford Mustang. 8-32 threaded hex machine screw like the originals. Attaches cables for heater only or factory A/C cables.

Reproduction A/C discharge service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 3/4" fitting. This valve accepts the R134A connection, not the R12.

Reproduction A/C suction service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 7/8" hose fitting. Replaces part # D0AZ-19752-A or D0AA-19752-A.

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Expansion valve for factory air conditioning for the Mercury Cougar or Ford Mustang.Will work with both R12 and R134 systems.Replaces part #: D1ZZ-19849.

Exact replacement to original drier that removes moisture and should be changed anytime system is recharged. It really is the life of your system. This stainless steel filter element stops contaminants from clogging the expansion valve.

High quality and correct looking air conditioning discharge hose for Mercury Cougars or Ford Mustangs. This hose is compatible with both 134a and R12 refrigerants.

High quality and correct looking air conditioning suction hose for the Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

Quick disconnect that installs between the sight glass hose and the sight glass to A/C dryer hose. This unit also includes 2 O-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

Regardless of which V-8 engine, D1ZA-19972-AA or D1ZA-19972-AB part number. This hose is approximately 24 inches long. These used hoses probably still hold pressure, we suggest a purchase of new 'O' rings prior to installation.

Regardless of which V-8 engine, D1ZA-19867-BC part number. This hose is approximately 49 inches long.

This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...

Click on images to enlarge. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342). One of the major differences between the reproduction and the original sight glass hoses, is that the texture of the originals was much more defined.  You can see and feel the ridges in the hose on the originals.  Below is a close up picture of repro and used side by side, and it is obvious that the repro is not nearly as textured as the originals...

Good used hose that connects the sight glass hose to the Air Conditioning Dryer. Includes the sight glass to dryer hose (Ford Part # D1ZA-19835-A), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.   

Used A/C suction service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch 'O'-ring fitting for suction hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Used A/C discharge service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch 'O'-ring fitting for discharge hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

These reproduction convertible panels are made from ABS plastic, are vacuum-formed, and made to outlast the originals. However, they only come in black and are sold as a pair.  These panels DO NOT have the holes cut in them for the retracting seat belts, so 72 and 73 Cougar owners will need to cut these holes. In addition, you will have to cut the holes for the ashtray and power window switch or manual window crank as well as install the snaps for the top boot. This will of...

Used bracket for installing the rear interior panels on any 1971-73 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. Replaces Ford part number D1ZZ-76310A84-A. 

This is an inexpensive top that is only recommended if you car is going to be stored indoors. Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our in-depth installation video below! ...