All Available Parts - 1970 Ford Mustang

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.

Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A. 

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

Exhaust manifold flange rings or 'doughnuts' for stock cast iron 428CJ exhaust manifolds. These are the malleable type that conform and slightly crush. Inside diameter just over 2-1/8 inches. Sold individually, two needed per car.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction Upper Control Arm To Shock Tower bolt.  Sold individually. Replaces Ford part # 38049-S

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

Complete 22 bolt set for oil pan on the 70 - 73 Cougar or Mustang.  

Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Phillips flat head machine screw for attaching bucket seat, seat back release catch on any 1968-70 Mercury Cougar or Ford Mustang including bench seat cars. Original screws are trilobed, meaning that they have triangle shaped threads instead of perfectly round. Helps with locking. We recommend using locktite or some other thread sealer when installing. Or at least check the torque after several weeks of use. 5/16-18 flat head machine screw, zinc plated.

Spring nut used to install the fan shroud on a 1967-71 Cougar or Mustang, 4 per car.

Hardware kit for installing the fuel pump on 70 - 73 Cougar and Mustang equipped with the 351 Cleveland engine.

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.  New AccuMatch flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1970 Cougar and Mustang blue interior color. Although you can use this for a wide verity of vehicles, it's a spot on match to the blue interior found on 1970 Cougar and Mustang. It's sold...

Here's a good replacement for those old worn out aluminum "stereo" decal inserts for your 69 - 70 door speaker grills. Keep in mind that these are just simple decal stickers and are not made from aluminum as the originals were. We do offer used aluminum decals here.SOLD INDIVIDUALLY. ...

This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...

NOS A/C expansion valve for Mercury Cougar or Ford Mustang. Great for that concours restoration because it is often little details like this that separate 1st from 2nd place at the show!Ford part # C9ZZ-19849-A

New Old Stock NOS passenger side front turn signal bezel. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13210-A, casting number C9WB-132_7

New Old Stock NOS driver side front turn signal bezel. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13212-A, casting number C9WB-13237-A

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

C9ZZ-2454-A

NOS C7ZZ-6522428-A Passenger side large size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

Oil pan baffle as found on all 1969-70 Ford and Mercury products with R or Q code 428CJ or 428SCJ engines. This baffle is sandwiched between the oil pan and the block.

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  NOS power steering control valve seal kit.  Ford part number C3AZ-3A650-B. ...

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

New old stock Chrome radiator cap. Motorcraft stamped, with RS-512A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9ZZ-8100-A.

New old stock seat belt bolt, has the "A" marking on the head. 1-3/8 inches long bolt for seat belts. Torks head, not sure of the exact placement in the car. Ford box has 'Campaign M9D Bolt' as the description.  Ford part number 382624-S100.

New old stock manual transmission shift lever boot. Attaches to the bell housing on FE big block cars. 1967-70 Mercury Cougar and Ford Mustang, 1966-71 Ford Fairlane / Torino. No comparison to the repro, this is much better.  Replaces Ford Part #: C6OZ-7513-A.

NOS, new old stock bracket and pulley assembly with new installed bearing for 1968-69 Cougar or Mustang equipped with the 390 or 428CJ engine. We also offer a bearing replacement service to rebuild your fixed idler pulley, see item 27539. Ford part # C8AZ-8678-B. Check out this video

NOS, new old stock Equalizer bar or "Z" bar for 351 cubic inch Cleveland engines with a manual transmission. Fits all 1970 Mercury Cougar and Ford Mustang with 351C engines and manual transmissions, Both 3 and 4 speed manual transmissions.  See the 1969 listing if you have a 1970 351 Windsor engine. Ford part number .

NOS distributor lead wire with green boot for the coil. Direct replacement for 1968-73 Ford distributors. There were several colors of boots that go to the coil, this is a green one as shown. Ford part number C7VY-12216-A.

NOS distributor ground wire. Direct replacement for 1967-73 Ford distributors. New old stock cable for inside the distributor, non ferrous metal, brass? Ford part number D2AZ-12264-A.

New Old Stock driver side door ajar switch for any 1969-70 Mercury Cougar or Ford Mustang with specific option. Standard on XR7, normally part of the convenience group option. Ford part number C9WY-14018-B.

New old stock power steering ram cylinder boot, rubber boot only. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C3AZ-3C651-A.

NOS C7ZB-6522448-A Passenger side small size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

NOS C7ZB-6522449-A Driver side small size pad or gasket for the exterior door handle. Driver side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

Reproduction trunk wheel house seam cover for the Ford Mustang. I have actually never seen an original pair of these on a car, but they do serve a purpose if you are in the habit of cramming your trunk full of items you do not want scratched. These attach to the protruding seam where the inner and outer wheelhouse bond together and measure about 14" in length. You will have to modify these to fit your Cougar. Only sold in black. Replaces Ford part # C5ZZ-6531466-A.

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.

This Steering Box Cover Gasket Reproduction fits the 67, 68, 69, and 70. Replaces Ford part #: C3DZ-3581. If your original steering box is one of the few that is still tight then you will want to open it up, clean out all the decades old solidified grease and put new grease in.

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Will fit the 69 coupe or convertible as well, but correct for the 70. Replaces Ford part # D0ZZ-6528182 Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Seals the lenses to the light body mounted in the front valance. Replaces Ford part # C9WY-13211. Sold as a pair. Also used on 1970 Mach I and 1969 - 1970 Shelby.

Seals the chrome marker light bezel to body. Seals the chrome marker light bezel to body. Their function is to keep water from entering the trunk around the rear lights. No gasket is needed on the front side markers. Replaces Ford part #D0ZZ-15447. These are designed for the Mustang and do not fit the Cougar without trimming. Sold as a pair.

These white foam gaskets fit between the sealed lens assembly and the chrome side marker light housing. They are sold as a pair. Replaces Ford part number D0ZZ-15209. *NOTE* To separate the sealed plastic lens assembly from the chrome bezels you will have to gently break away the edges of the factory "melted over" plastic stud. A drop or two of your favorite adhesive will reattach them but this is not crucial as the two threaded studs keep everything tied together once they are mounted back to...

Replaces Ford part #C7AZ-13568

Fits along the lip of the cowl cover and seals to the underside of the hood. Replaces Ford Part #C9ZZ-16740. 

44 Piece kit that includes quarter panel drain plugs.

This kit is designed for the 1969-1970 heater A/C box. Replaces Ford Part #: C9ZZ-18500-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

Correct heater box seal kit for 1969 and 1970 Cougars and Mustangs. Replaces Ford part #: C9ZZ-18500-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

Fills the hole in the core support where the A/C lines pass through to the condenser. Replaces part # C9ZZ-19819.

These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.

This reproduction is made from the original Ford tooling and is new to the market. Well worth the few extra dollars over the previous ones offered. Replaces Ford Part #: C6OZ-7513-A.

Used to seal the Aluminum shifter housing to the transmission tunnel. Replaces Ford part #: C9ZZ-7370. Check out this video

We suggest using white lithium grease or petroleum jelly to ensure the seal will not stick to the shift lever. Fits 1969-73 Mercury Cougar and Ford Mustang, additionally it also fits 1971+ Maverick and Comet with floor shift automatic only.  If you have any side-to-side play in the shifter, this seal will not last. We do have the shifter bushings available. Replaces Ford part  numbers C9ZZ-7D351-A & D1ZZ-7D351-A. Get the matching mounting clips here. Check...

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! Check out this...

NEW DESIGN... The consistency of rubber on these strips is soft and supple now.  The doors do not have to be "slammed"  Of the three reproductions versions out, there these are the best.   If you have any NOS to sell we would like to hear about them.Replaces Ford part #: C9ZZ-7602626

NEW DESIGN... The consistency of rubber on these strips is soft and supple now. The doors do not have to be "slammed" Of the three reproductions versions out there, these are the best. If you have any NOS to sell we would like to hear about them. Replaces Ford part #: C9ZZ-7602627

Rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors.Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B Check out our...

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

Comes with attaching staples made of stainless steel. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. Replaces Ford part #: C4DZ-16238.Not all cars were assembled with this seal, some came with staples, and others used clips.

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

Sold as a pair. Two required per car.Replaces Ford Part #: 380239.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

Perfect fit. Replaces Ford part #: C9ZZ-3513.

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

Metal core base as original, correct texture. If you have a 1970 with a Hurst four speed then the one with the rectangular hole is correct for the Hurst shifter. Replaces Ford part # C9ZZ-7277-A. Check out this video

Replaces Ford Part # : D0OZ-7583

This kit includes all the rubber plugs needed for the inner cowl panel as well as two windshield stops. These plugs will help ensure your Cougar's cowl panel doesn't get damaged due to moisture or small pieces of road debris. Each of the eight (8) plugs are constructed from high-quality rubber and are designed to be OEM-style

The picture above shows these bumpers installed in the 100% correct reproduction console that we sell. These are sold individually, 2 required per car. Replaces Ford part # 379919.

Pair of anti rattle spacers / guards that go between the fender and the cowl on each side. The majority of 1969 Cougars and Mustangs used a black foam block glued to the cowl but in late 1969 and all of 1970 these wedge shaped rubber parts were used. Replaces Ford part number C9ZZ-16758-A.