All Available Parts - 1970 Ford Mustang

Used moulding for 'upper windshield garnish' for any 1970 Mercury Cougar or 1969-70 Ford Mustang. This item not for 1969 Cougar hardtops or for convertibles. Item comes in black as shown, paint to match non-black interiors. Ford part # C9ZZ-6503606-A.

Reproduction saddle headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

These hinge covers are exact copies of the originals. These are neutral in color so you can paint them to match your interior color.

Correct texture, good fit. Sold as a set of four in black or neutral only. We have a large collection of used covers in all colors for all years.

Replace those tarnished handles and broken or missing bezels on your seats with our new bright chrome pieces. Our handles are pressure die cast zinc with a durable polished chrome finish.

A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat back when positioned forward. This bracket carries a D7AA-69618C46-A or D7ZZ-69618C46-A service replacement part number. Without...

These are often cracked or collapsed causing your seats to lean back too far. One kit does one seat, two kits required per car.*NOTE* Don't discard your original screws! The screws supplied with this kit have a head that is just slightly smaller than original so when you really tighten the screws down the head goes right on through the stop! A very small washer will cure the problem if you choose to use the screws supplied. Replaces Ford Parts #: C8ZZ-6560310 & C8ZZ-6560311

Sold as a pair

Fits RH or LH standard interior, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar.Sold individually Replaces Ford part #: C9ZZ-6560762.

Fits RH or LH standard interior, sold individually, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Available in black only, use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar. Replaces Ford part #: C9ZZ-6560762. ...

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

Complete seat frame for the 1969 Eliminator or Mach 1 and all models in 1970. We highly recommend good used as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Passenger side shown.

Complete seat frame for the 1969 Eliminator or Mach 1 and all models in 1970. We highly recommend good used as they are more correct and significantly less expensive. These are drop shipped directly from the manufacturer. Passenger side shown.

Core driver side (left hand) high back bucket seat for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your 1967-69 Cougar, your existing seat tracks...

Core passenger side (right hand) high back bucket seat for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your 1967-69 Cougar, your existing seat...

Used passenger side inner bucket seat blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat blue hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat white or parchment hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat white or parchment hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat white or parchment hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat parchment or white hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side inner bucket seat ivy green hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat ivy green hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat ivy green hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number D0ZB-6561694.

Used driver side outer bucket seat ivy green hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number D0ZB-6561695.

Used passenger side inner bucket seat ginger hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat ginger hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used passenger side outer bucket seat ginger hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number D0ZB-6561694.

Used driver side outer bucket seat ginger hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number D0ZB-6561695.

Not an exact replacement, but a decent replacement if you have a rear view mirror that the silver is peeling on. Includes new glue on mounting tab (bracket). Replaces Ford Part #: C8AZ-17700-A. This picture below shows the rear view mirror variations from 1967-1973. Check out this video ...

This special bracket gets glued to the windshield glass. Rear view mirror mounts on it. Plain finish. Replaces Ford Part #: C9AZ-17698-A.

These rear view mirror lenses are sold on an exchange basis.  Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until the glass...

1970 California evaporative system. Tapered hose. This item is not reproduced and it is getting to be hard to find a good pliable hose with no damage.Filler neck not included.

Reproduction aqua headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction dark blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction light blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.

Good used passenger side plastic trim that will need repaint, and the screw hole hidden behind the dash pad is almost always cracked. The 1969 XR7 and Decor models used the padded version.Limited colors available, please specify in the notes when ordering as to which color you want and we will do our best to accomodate you.

Good used driver side plastic trim that will need repaint, and the screw hole hidden behind the dash pad is almost always cracked. The 1969 XR7 and Decor models used the padded version.Limited colors available, please specify in the notes when ordering as to which color you want and we will do our best to accomodate you.

Used passenger side outer bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used passenger side inner bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561692.

Used driver side inner bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to stock on hand. Ford number C8ZB-6561693.

Used driver side outer bucket seat black hinge cover, for any 1968-70 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Used passenger side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561694 number possibly. Ford number D0ZB-6561694. ...

Inner tie rod end for 1970 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: D0ZZ-3A131-B.

Outer tie rod end for 1970 – 1973 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Includes 1969 Boss 302 Eliminator and Mustang, and 1970-74 Ford Maverick and Mercury Comet. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: D0OZ-3A130-B.

Sleeve and hardware for joining the inner and outer tie rods together. This also is a 'toe in' adjustment part. Sold individually, two needed per car. Replaces Ford Part #: C2AA-3310-A

Import reproduction. Fits 1967-70 Mercury Cougar or Ford Mustang without power steering. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Click on images to enlarge. ...

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.

Now an inexpensive and easy way to convert 1967 - 1970 power steering cars to manual steering. This will give you a more precise feel for the road or track. Eliminates leaking systems and costly repairs. Installs in minutes with no special tools.

1967 - 1970 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Note that early 67's will have a 1" sector shaft. Check out this video

These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a...

C9ZA-3590-B 1969 - 1970 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C9ZZ-3590-B.

Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can rebuild your box with this kit. SMB-K, SMB-D, and SMB-F tagged steering boxes. Probably a DIY youtube video out there for...

This is the most complete kit available for the steering box with 1-1/8 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can...

This is the most complete kit available for the steering box with 1 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your EARLY short shaft 1967 Cougar or Mustang steering box only with the 1 inch diameter sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a...

Reproduction D0ZZ-3304-A Manual steering drag link for all 1970 Cougar and Mustang and 1969 Boss 302 Cougar Eliminator & Boss2 Mustang with a non-power assist manual steering system. This is the same as 1969 manual steering drag link, but with larger holes for 1970 ball joints. Meaning more heavy duty, Boss2 specifications if you will. *Note - if installing on a 1969 Mercury Cougar or Ford Mustang, you will need to use 1970 inner tie rod ends. 

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Replaces Ford part # C7AZ-3A006-C or D1VY-3A006-A.

Replaces Ford part # C7AZ-3A006-C of D1VY-3A006-A.

1967 - 1971 Ford power steering pump dipstick. Used until 2-8-1971.

Due to the vulnerable location of the control valve these often get cracked or worn through from rubbing on other components. Fits most all Ford passenger cars 1962-1970. Replaces Ford part number C2AZ-3C705-B

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

NOTE - Some customer are experiencing problems with this economy idler arm, the castle nut on top is causing clearance issues with the bolt on the top arm.Import reproduction. Fits 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering.

Premium grade of idler arm. Fits all 1967-70 Mercury Cougar and Ford Mustang. If you have loose / sloppy steering, replacing this part could help tighten things up. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Drag link hole size: 5/8" Customer feedback: Hey, just wanted to thank you for your prompt service. Last Friday...

Power steering drag link for all 1970 Cougar and Mustang and 1969 Boss 302 Cougar Eliminator & Boss2 Mustang with power assist manual steering system. This power steering drag link may have a 1970 part number, but it is basically the same as the 1969 Boss 302 version, which was much thicker than the standard 1969 power steering drag link. Can be installed on 1969 Mercury Cougar and Ford Mustangs as long as you upgrade to 1970 inner tie rods.The 1970 drag link measures about 0.850 inches...

Sold individually # 377112-S

Great kit for those that have a good used power steering control valve unit to rebuild.  Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #: C2AZ-3A533-A.

Power steering pitman arm for any 1967-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Check out this video

Premium quality original FORD valve that has been re-manufactured to original tolerances. Quality part that is rebuilt by a true craftsman here in the USA. *NOTE: Our rebuilt and reproduction control valves all come pre-lubed with the correct amount of grease. If out of the box you add more grease, you will damage the valve. Unlike some suspension parts these are not designed to add grease until you see the grease coming out of the seal. Our warranty does not cover over lubricating. ...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm.These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will...

Used Nuts for attaching the oil reservoir to the pump. Two nuts used for attaching the reservoir to the pump. Nuts fit the high pressure port. This is a pair of nuts. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, on 1970 Mercury Cougar and Ford Mustang. 1970 428CJ engines used a different pump with smaller diameter line fitting.

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

These are the newest steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be a great buy because of the fact that they come with a lifetime guarantee. These gear boxes are not rebuilt, as are the rest of the boxes we carry, so there's also no core charge. 16:1 ratio NOTE* The supplier specifies that these steering boxes are made with new and used parts. Check out this video ...

Reproduction spool for the control valve on your 67 - 70 Cougar or Mustang.

New castle nut for all power steering control valve ball stud found on 1967-70 Mercury Cougar and Ford Mustang. 3/4 inch hex nut, with 1/2-20 threads. Connects the Pitman arm to the ball stud on the P/S control valve. Don't forget the cotter pin. Verify your shop manual for correct year torque specifications. We found one source of 28-35 FT LBS. for the Pitman Arm nut to control valve. Ford numbers for attaching nut: 1967-68 351059-S, 1969-70 385002-S.

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  ...

Most complete kit available for rebuilding the late 1967-70 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate reproduction. 

Sold individually, right is the same as left.  NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have the strut rods available in both new and used form. Find them here. Replaces Ford part # C8OZ-3078-A. Check out this video ...

You can use 1968 up to 1973 lower control arms on a 1967 only if you change the strut rod to the 1968 - 1970 style. We have the strut rods available in both new and used form. Replaces Ford part #: C8OZ-3078-A. Sold individually, right is the same as left. *NOTE* The Cougar only, 1967 only, lower control arm is not available in reproduction form but you can rebuild the originals so do not throw away your cores as they may prove to be valuable one day. Mustang never used the articulated strut...

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Check out this video

Sold individually, two required per car. These are brand new, not rebuilds. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford Part #: C7DZ-3082-A. Fits 1967-70 Mercury Cougar and Ford Mustang. We have found that this economy version does not fit 1971-73. There just is not enough clearance for this unit to bolt into the shock tower. Check out this video

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

Complete kit with shaft for one side. Includes grease seals and zerk fittings. Note! Often times the fine threads in the upper control arms will be worn to the point of being stripped. To keep this kit properly in place you may have to tack weld the threaded caps to the control arms in a couple of places.

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. This is the reproduction cross member offered by most of the Mustang...

Passenger side disc brake spindle for 1970 Mercury Cougar and Ford Mustang. Ford part number D0OZ-3105-B right hand or passenger side disc brake spindle. Ford part number D0OZ-3106-B left hand or drivers side disc brake spindle.We have to price our disc brake spindles so as not to deplete our complete used conversion kits. Ford casting number D0ZA-3107-C. Check out this video

This gas shock improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock. Also, this is the most stock-looking shock since it's black and has a flat upper collar. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.259.334.92-X- ...

KYB Gas-a-just shocks are America's best selling performance gas shock. It's monotube design features a higher gas pressure which helps to hold the tire to road surface during severe driving conditions. N2 gas helps eliminate shock fading due to aeration and foaming. This shock is the perfect choice for the performance oriented. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.029.614.41-X- ...