All Available Parts - 1970 Mercury Cougar

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Used upper and lower inner steering column shafts for a fixed steering column on the 1970 Cougar or Mustang. Bushings will be intact and in good shape.

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Reproduction transmission selector tube seal for the 69 - 70 Cougar or Mustang steering columns.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

Reproduction black oil cap for your 67 - 70 Cougar or Mustang, featuring the FoMoCo logo.

Chromed "Autolite" oil filler cap, original cap chromed, not reproduction. Bare cap, will need baffle material added. Also recommend purchase of a rubber grommet and either plastic or steel PCV elbow. Your specific application will determine if plastic or steel elbow. See related items. C8AZ-6766-B$40 refundable core charge does apply.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Oil filler cap elbow for hose that goes to the air cleaner elbow. Black plastic like original, fits 1968-70 Mercury Cougar and Ford and Mustang. See related items for grommet and other related parts.

Spark Plug Wire Separator Brackets for the 1969 - 1970 Mustang Cougar or Torino with 428CJ Finned Aluminum Valve Covers, 1969 - 1970 Mustang Boss 302 with Finned Aluminum Valve Covers or Boss 351 models. These are an MCA approved unit made here in the USA. These replace Ford part number C9ZZ-6583-A and include both brackets and the 4 screws to properly install these units. Attaches spark plug wire holder to the factory finned aluminum valve covers

SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.

351C VALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1970-1973 Mercury Cougar and Ford Mustang with 351C engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2SZ-6582-A & D2SZ-6582-B. Although we have more of these in inventory, we do not recommend them because the remaining quantities will be less than desireable. *Note - This cover will not work on a 351 Windsor engine. ...

Reproduction pair of aluminum 428CJ valve covers. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Sometimes called 1969 Shelby valve covers. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of  "Snake" finned aluminum valve covers.

Fits 1968 - 1970 Standard or XR7

Fits 1967 and 1968 Standard or XR7. Holds "J" shaped plastic hinge covers in place.

1969-70 actually used a star head bolt but these are a much more user friendly screw that will work in its place. Sold in a set of four which is what you will need for one seat.

Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Fits Standard or XR7. Sold as a pair.

Fits 1967 - 1973 Standard or XR7

Fits 1968 Standard or XR7

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Fits 1968 - 1973 Standard or XR7

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.

Sold individually. Two needed for globe box cable 1967-70 Mercury Cougar. 3 needed for installation of turn signal switches 1967-73 Mercury Cougar or Ford Mustang.Ford number 379203-S. Phosphate & Oil (gray-black)

Fits 1967 and 1968 Standard or XR7

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Sold individually # 374212-S

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

Bulk pack of 100 oval head phillips screws for door and window crank handles.

New 8-32 set screw for the rear window crank handles. Fits 1968-70 Mercury Cougar and Ford Mustang. Allen hex size of 5/64".

Used Bonded Design Passenger Side Power Window Regulator for the 1969 and 1970 Mercury Cougar

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Hex head screw for attaching floor drain hole covers. Several different screws were used over the years and at different plants. All seem to be a #8 sheet metal screw of varying lengths. This is a #8 hex washer head tapping screw with 5/8" length. Two screws per drain cover, 2 or 4? per car, not sure. We also have the drain covers. 

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)

These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Missing some of the hardware used to bolt on your shock tower braces? Here are our reproduction shock tower brace mounting kit for the Mercury Cougar or Ford Mustang.

1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

Multiple uses.5/8" from bend to center hole.

Used for multiple applications. 7/8" from bend to center hole.

Bag of 25 reproduction j-nuts for the front fenders on the Mercury Cougar or Ford Mustang.5/8" from bend to center hole.

Self threading speed nut for attaching "COUGAR' scrip emblems to the rear quarter panel of any 68 - 70 Mercury Cougar. Sold individually, 4 needed per emblem. Whereas these work fine, the originals were an acorn style nut and look very different.

24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Also sold individually.

Replaces Ford part # C2DZ-6A529 Sold Individually.

This is the shorter version of the top-loader with no "+" on the head. Sold individually

Replaces Ford part # 385664-S

Sold individually Zinc (dark silver)

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).

Sold individually Zinc (dark silver)

Sold individually Zinc (dark silver)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually Zinc Dichromate (yellow-rainbow)

This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292

Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.

Replaces Ford Part # 50828-S Sold individually. Zinc Dichromate (yellow-rainbow)

These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.

Sold individually. Zinc Dichromate (yellow-rainbow)

Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang

Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...

New valve cover bolts for all 289-2V, 289-4V, 302-2V, 302-4V, and 351W-2V, and 351W-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 12.*Note - Excludes Boss 302 and 351C engines (see part  number 8317)Replaces Ford part number 373071-S.

Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S

Reproduction alternator mounting kit for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Spacer not included, but available.

New set of bolts for fastening the transmission inspection cover on all 1967-70 Mercury Cougar, Ford Mustang, and Ford anything with 390, 428CJ, and 352 or any FE style Ford engine. Includes 3 and 4 speed transmissions.

New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Reproduction valve cover bolts for all 390 / 427 / 428 Ford engines.

Reproduction bolts and washers for the C-6 automatic bell housing on any 1967-70 Cougar or Mustang equipped with a 390 / 428 engines and code U automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford big block V-8's from 1966-70.

New Bolt kit, for the installation of a water pump on any Ford 351C or 351 Cleveland engine. Fits all 1970-74 Mercury Cougar and Ford Mustang with 351C, 351CJ engines. 11 total pieces in the kit as shown.

New Bolt kit, for the installation of a water pump on 1970-73 Ford 302, Boss 302, or 351W engine. Fits all 1970 Mercury Cougar and 1970-73 Ford Mustangs. 9 total pieces in the kit as shown.

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt set for any 1967-70 Ford 390 or 428CJ engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford FE engines.  See related items for individual long or short cylinder head bolts.

Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Sold individually, 2 required. Ford Part #: C8AZ-2B296-A Check out our caliper tips and tricks video below: ...

9" inside the arch to the end of the threads. Thread size 7/16-20, includes tall nuts as shown. Concours Grade 5 flange nuts available separately, see related items.

Replaces Ford Part # 381985-S Sold individually

Factory OEM style clamp for attaching the brake booster vacuum hose to the check valve. Also same clamp for securing the rubber boot to the power steering ram cylinder. Sold individually.

Replaces Ford Part # C8AZ-2B164-A Sold individually

These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individuallyCheck out our caliper tips and tricks video below: ...

Replaces Ford Part # 382713-S Sold individuallyCheck out our caliper tips and tricks video below: ...

Replaces Ford Part # C8AZ-2066-A Sold individually