All Available Parts - 1970 Mercury Cougar

Replacement LED light that replaces the 212 bulb for the door courtesy lights on your 69 - 70, or the map lights on the 71 - 73 Cougar. These LED's give a fuller, brighter effect as compared to standard incandescent bulbs.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Wire harness extension that runs from the under dash harness to the A/C fan control switch on any 69 - 70 Cougar Standard or XR7, or the 69 - 70 Mustang.Ford part number C9ZA-19945-B

Wire extension for horn relocation, when the drag pak or drag pack option was ordered typically with 3.91 or 4.30 rear axle ratio. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory oil coolers. Should also fit Torino and Cyclone. Reproduction of Ford part number C9DB-13A840-A.

Concourse Correct Timing Pointer for the 1968 - 1970 390, 390GT or 428CJ. Technically, by design, this is a copy of a 1969-70 390/428CJ timing pointer. It will also work for 1968, since the harmonic balancers and timing covers are the same.Replaces Part # C9AZ-6023-A.* Note - not correct for 428 Super Cobra Jet, see related item.

Concourse Correct Timing Pointer for any 428 Super Cobra Jet Replaces Part Number C9OZ-6023-A.

3/8-16 X 7/8 9/16 AF .75 OD Sold individually. Fits all 390 & 428. Replaces Ford Part #: 374409-S.

Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Original used 390 or 428 Cobra Jet piston connecting rod. These are marked C7AE-B. Rods and caps only. We strongly suggest using ARP aftermarket rod bolts. Limited quantity available, call to inquire. Replaces Ford part number C7AE-B and C6AZ-6200-C. *Note - Excludes 428 Super Cobra Jet engines.

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

Timing chain set for your 67 - 72 Cougar or Mustang equipped with the 302 Engine.Gears (sprockets) are made from high alloy steel, and heat-treated for durability. Chain is pre-stressed and heat-treated for longevity.

Used stamped steel pointer mounts to timing chain cover. Correct for 1970 Mercury Cougar with 351W engine, and 1970-72 Ford Mustang 302 and 351W. At least two distinct versions of this pointer may be availbable. Starting in 1970, Ford V-8 engines had timing pointers installed on the passenger side of the engine, and a companion harmonic balancer with 4 bolts for attaching crank shaft pulleys. Uses two of the timing cover bolts for attaching. Replaces Ford part C9TZ-6023-A. This icon means that...

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in most 1970-72 Mercury Cougar or Ford anything including Mustang. Can be used on any 1970-74 351C engine from Ford. Technically, 1972 California 351C cars and 1973 351C cars used a different timing pointer for what ever reason. Replaces Ford part D0AZ-6023-A.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1969-70 Mercury Cougar and Ford Mustang with 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Replaces Ford part C9AZ-6023-A.* Note 428 Super Cobra Jet uses a different pointer, see related.

Reproduction oil pressure remote sending unit tube assembly. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge.The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell shaped oil...

Reproduction oil pressure remote sending unit tube assembly mounting kit.. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge. The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell...

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Brass and steel freeze plug or expansion plug set for any Ford 351C engine. 1970-74 Mercury Cougar and 1970-73 Ford Mustang. 12 piece set with threaded screw in plugs as shown. 

Brass and steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 20 piece set with threaded screw in plugs as shown. 

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

Fuel pump drive eccentric for Ford 351C engines 1970-74. Used eccentric from our wrecking yard. Includes inner and outer eccentrics, bolt, and washer. 2-1/2 inches in diameter. Ford part number D0AZ-6287-A.

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

White reproduction fan for the Thermactor Smog Pump.

Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.

Like working on your Cougar's engine? Keep your Cougar's fender from getting scratched with this Cougar fender gripper. Check out this video

This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification (in states where front plates are optional), for-sale pictures, and even as standalone wall decoration. Plus it makes a great gift for the Cougar lover who has everything else!

This 12" x 18" parking sign is the perfect way for your Cougar to mark its territory. Bold red lettering announces that lesser cars are not welcome. Durable .040 gauge aluminum with two pre-drilled holes for easy hanging. Makes a great gift!Our review: Print quality isn't as crisp as actual road signs if you look real close, but it looks good from a couple feet away. Seems durable enough for outdoor use. We're testing them in the parking lot outside our shop for UV resistance, stand by for an...

This great new '67 Cougar "blueprint" poster is a cool display piece for any Cougar fan. We did our homework and compiled information from multiple sources, including official Lincoln-Mercury documentation and independent magazine articles about the 1967 Cougar, to create this official-looking piece. Printed on heavyweight 48lb. satin bond paper, it has the look and feel of a real blueprint, with the durability of an archival art print. Measuring a full 24"x36", it's an eye-catching piece to...

For the Cougar fan who has everything! This is a unique, awesome piece to hang on your wall. Made from laser-cut 18-gauge steel, rusted on the surface for a unique patina. Features a walking cat logo and COUGAR lettering. Measures 24" wide by 13" tall.We can also customize your sign for an extra $50 - such as your last name, business name, Joe's Garage, or whatever you'd like in lieu of "COUGAR", as long as we can make it fit (20 characters or less). Mention it in the order comments and we'll...

We're pleased to offer a 5 layer car cover that is composed of the thickest and most reliable fabric available in today's market. With the most technologically advanced material, this cover is guaranteed to protect your car from extreme weather conditions such as heavy rain, snow, ice, sun and wind. This heavy-duty, 100% waterproof cover insures perfect protection all-year-round for both indoor and outdoor use. It features three bonded layers of polypropylene, a micro-porous film layer...

Single cylinder head from 1970-73 Mercury Cougar with H code 351C-2V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.65 inch valves, and the chambers measure out at 78.2 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-J. 2V in the...

New Cougar Drive-In poster by WCCC! This 20" x 30" poster is printed on heavyweight matte archival paper and features a satin finish. Suitable for framing, this print would make a great decoration in your garage or living room. This photo was taken at our annual Open House event in 2013.Here's a video of our 2013 Open House event! ...

New large black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 21" X 9" X 9" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

This listing is for anyone who wants to order a custom set of floor mats. Simply add this item to your cart, and in the order notes section of your order, let us know which carpet color you want (please choose from the available options in color sample photo above or if ordering at the same time as a carpet kit simple say "please match ordered carpet color") and which script you would like, whether it be the Walking Cat, Cougar Head Logo, XR7, The Cougar Script or the GT...

These floor mats were available as part of the factory "protection package" or as a dealer accessory when these cars were new. Good used originals have gotten VERY hard to find. At present (9-20-18) they are only available in black. Keep in mind the 69-73 convertible used a narrower mat to clear the inner rockers. We have a diagram that shows you where to trim for your convertible. The walking Cougar logo is a favorite of any Cougar fan. The Cougar became so popular that soon after the Cougar...

Reproduction sound deadener for the seat divider on the 1967 - 1970 Mercury Cougar. This reproduction is as close to the original as possible, and is comprised of a mastic material. This item is trimmable and will fit bot the 67 - 68 and 69 - 70 seat divider.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.

Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A. 

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

Exhaust manifold flange rings or 'doughnuts' for stock cast iron 428CJ exhaust manifolds. These are the malleable type that conform and slightly crush. Inside diameter just over 2-1/8 inches. Sold individually, two needed per car.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction Upper Control Arm To Shock Tower bolt.  Sold individually. Replaces Ford part # 38049-S

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

Complete 22 bolt set for oil pan on the 70 - 73 Cougar or Mustang.  

Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Phillips flat head machine screw for attaching bucket seat, seat back release catch on any 1968-70 Mercury Cougar or Ford Mustang including bench seat cars. Original screws are trilobed, meaning that they have triangle shaped threads instead of perfectly round. Helps with locking. We recommend using locktite or some other thread sealer when installing. Or at least check the torque after several weeks of use. 5/16-18 flat head machine screw, zinc plated.

Spring nut used to install the fan shroud on a 1967-71 Cougar or Mustang, 4 per car.

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

New Old Stock gas door. Fits all 1969-70 Mercury Cougars. Ford part number C9WY-65405A26-A

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

Cougar poster by WCCC, featuring a 1969 XR7 Convertible against a stunning sunset and impressive skyline, this 20" x 30" poster is printed on heavyweight archival paper and features a semi-gloss finish. Suitable for framing, this print would make a great decoration in your garage or living room.  *NOTE - Please excuse the typo on our phone number at the bottom of the poster! The phone number on our business cards and at the bottom of our website is correct. ...

Over the years WCCC has supported many underprivileged individuals. And now through the help of one of our valued customers who is a retired corrections officer, we are offering these leather key fobs which were created and hand painted by inmates at the Oregon State Penitentiary. A great gift for any Cougar lover!  Measures 4" x 2-1/2"

Here's a good replacement for those old worn out aluminum "stereo" decal inserts for your 69 - 70 door speaker grills. Keep in mind that these are just simple decal stickers and are not made from aluminum as the originals were. We do offer used aluminum decals here.SOLD INDIVIDUALLY. ...

Of the 100,085 Cougars produced in 1969 only 1,505 came ordered as "radio delete". In 1970 a higher percentage came this way with a total of 1858 out of 72,365 total production. The total amount of 1969 - 1970 Cougars that came radio delete would be 3363. It is assumed that the majority of cars built radio delete would be the less optioned standard or decor models which would feature a pebble grain finish, color coded to the interior color. Most of the radio delete plates were discarded at the...

This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...

Left is the same as right, one year only emblem at the center top of the door panel. Usually will show a small amount of pitting. Casting number as seen on the back reads D0WB-6520802.

Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

This NOS passenger side back-up lens features the hard to find "frosted" finish. Later service replacement examples used a clear finish that gives a clear view to your lit or unlit bulb inside. Passenger side lens for 1969-70 Mercury Cougar. Ford part number: C9WY-15514-A

This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...

NOS A/C expansion valve for Mercury Cougar or Ford Mustang. Great for that concours restoration because it is often little details like this that separate 1st from 2nd place at the show!Ford part # C9ZZ-19849-A

New Old Stock NOS passenger side front turn signal bezel. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13210-A, casting number C9WB-132_7

NOS sequential unit for the taillights of the Mercury CougarFord part # D1WY-13A366-A.1971 Cougars built from 2/1/71 to 5/15/71 used a unique sequential system in the trunk, D1WY-13A366-C. It uses two connectors, grey and light blue, that are no longer serviced. When the sequential system must be serviced, it can be replaced by an NOS unit, or a replacement unit, such as the C9WY-13A366-AL sequencer shown below. Since these unique connectors are no longer available, the connector plugs on the...

New Old Stock NOS driver side front turn signal bezel. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13212-A, casting number C9WB-13237-A

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

C9ZZ-2454-A

Oil pan baffle as found on all 1969-70 Ford and Mercury products with R or Q code 428CJ or 428SCJ engines. This baffle is sandwiched between the oil pan and the block.

New Old Stock aka NOS XR7 shield hubcap and wheel cover for the 1969 Mercury Cougar with a WHITE inner ring. There were two versions of this cap, one with a white painted ring around the center, and one with black around the center. This white version was used in 1969, with the black version being used in 1970. Ford part # C9WY-1130-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

Ultra rare, highly sought after NOS bezel. Ford part #: D0WY-13489-A . This is a costly part but when you factor in the price of a clean core and the $400 (approximate) cost of restoration, the cost is understandable. Keep in mind a restored part will never have the exact look of a NOS part.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Very rare to find NOS these days! Very limited supply...Keep in mind that the 1970 XR7 Green is a slightly lighter green than in the 69. 

NOS passenger side (right hand) taillight lens for any 1969-70 Mercury Cougar. Ford part # C9WY-13450-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check out this LED Comparison video ...

This NOS driver side back-up lens features the hard to find "frosted" finish. Later service replacement examples used a clear finish that gives a clear view to your lit or unlit bulb inside. Ford part number: C9WY-15514-B

These originals had varying shades of blue, whereas the repro has a solid blue. VERY rare find in NOS form.Ford part # C9WY-1130-B

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

Gasoline or Fuel gauge assembly from a 1970 Mercury Standard Model. NOS new old stock. 1969 fuel gauges do not have any lettering on the warning lights. 1970 has the white lettering on "ALT" and "PARK" warning lights. Ford part number C9WY-9280-A. Check out the video below on our new gauge tester: ...

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

New old stock Chrome radiator cap. Motorcraft stamped, with RS-512A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9ZZ-8100-A.