All Available Parts - 1970 Mercury Cougar

(7526) Nylon plastic injected. Correct original design. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these.Replaces Ford Part #: C0AZ-7526-B.Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they...

Injection molded plastic stops underdash squeaking from clutch pedal return spring. 2 required per car. Replaces Ford Part #: C1DZ-7A630-A

Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR

Replaces Ford Part # : C7ZZ-7507-B

Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.

Reproduction engine side stud for the clutch equalizer bar or z-bar that fits a 289, 302, 351W, or 351C engines in the 67-70 Cougar or Mustang. 

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...

Swivel that mounts to the lower clutch rod or clutch adjusting rod. Original Ford part number D0ZZ-7A528-A.

Reproduction premium adjusting rod which includes: 2 Lock Nuts 1 Spacer 1 Retaining Clip Fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.

Nice reproduction of the original. Replacement Z-Bar for 1969 and 1970 351W engines with either 3 speed or 4 speed manual transmissions. Replaces Ford # C9ZZ-7528-A.

D0ZZ-7528-E reproduction Z-bar or clutch equalizer bar only for the Boss 302 Cougar Eliminator or Mustang. These are exact copies of the originals, and those used stock cast iron exhaust manifolds. There is no way to tell if this will work with headers.

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

Comes with everything shown to replace tracks on one seat, good quality reproduction made in China. Make sure and check out our good used originals if correctness is important to you.

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This is the upper pressure hose, or the pump end only. Lower pressure hose Replaces Ford Part # : D0OZ-3A719-C Click this link for more clarity on power steering hoses: https://secure.cougarpartscata...

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata... ...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1970 small block. This is the upper portion that connects to the one year only 1970 pump found on the 351c, 351w and BOSS 302 equipped cars. Like the originals, this is part one of a two part hose. This hose has industrial high pressure fittings that are much higher quality than those available by most Cougar / Mustang parts dealers. Replaces Ford Part #: D0OZ-3A319-A. Click this link for more clarity on power steering hoses:...

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

Single sheave pulley 6-61/64 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number C9OE-8509-G.  Ford part number C9OZ-8509-D Note:  * The Master Parts...

Premium power steering hose kit for the 1970 Cougar or Mustang with a small block. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata...

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Fits the 1969 and 1970 Mercury Cougar with the 302, Boss 302, 351 Cleveland or the 351 Windsor. Stiffer and 1/8" shorter than our other reproduction. Replaces Ford Part #: C9ZZ-7523-A.

Fits the 1969 and 1970 Mercury Cougar with the 390GT, 428CJ or 428SCJ. Replaces Ford Part #: C9ZZ-7523-B.

This spring is commonly missing or broken. Plated to prevent rusting and premature failure. Connects from the top of the equalizer bar to the firewall. Close Reproduction. Slightly longer and softer than our concours spring. Replaces Ford Part #: C9ZZ-7523-A.

(7521) Correct Contour and fit. Connects pedal to Equalizer bar. Fits all engine sizes 3 and 4 speed. Replaces Ford Part #: C9ZZ-7521-C.

Reproduction clutch pedal return spring, comes complete with two new nylon bushings. Replaces Ford Part #: C8OZ-7534-B.

Replaces Ford Part # : C9ZZ-7591-A

Lower clutch rod and adjusting nuts to ensure proper clutch operation. For the Boss 302 and 351. Unless you have your original swivel, also see item 11773. This part goes between the nuts. Replaces Ford Part #: C9OZ-7521-A.

Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.

This is a non-concours upper clutch equalizer or Z-Bar to firewall spring that fits the 390 and 428 Cobra Jet in the 1969 - 1970 Mercury Cougar or the 1969 - 1970 Ford Mustang.

[No Description Provided]

Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1970 dual exhaust Cougars, all engines. Originally the tail pipe clamp would have been spot welded to the pipe, rarely will we be able to provide these with the original clamp in place. Ford part number DOZZ-5260-C.

Here is our free download for the 1968 Mercury Cougar sunroof panel service procedures.

13MB Downloadable PDF file of the complete 1970 Mercury Cougar electrical wiring diagram used by Ford Technicians. You will receive a download link both on the order confirmation screen and via email once your order is complete. In this download you will find diagrams for the following systems: Air Conditioning Brake Lights Charging Cigar / Cigarette Lighter Circuit Protection Clock Convenience Systems Convertible Top Defogger Exterior Lights Gauges Head Lamp on Warning Buzzer Heater Defroster...

Here is our free 7MB download for the 1967 - 1972 Mercury Cougar suspension diagram.

Replacement U-nut or clip for any 1967-70 Mercury Cougar trunk lid. These slide into the bottom of the trunk lid for attaching the hinges. Correct 5/16-18 threads, 7/8" from center of hole to edge. 4 total per trunk lid, sold individually.

Installation kit for the fastening the new reproduction deck lids to the trunk hinges on the 67 - 70 Mercury Cougar. The reproduction deck lids don't come with the J nuts installed and we've found this set to be a perfect fit.

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Replaces Ford Part # 359747-S

Master clip kit which include the following fasteners:Door courtesy and speakerEngine feedFirewallFront crossmemberHorn feedParking light leadsPassenger side cowl brace and alternatorPassenger side shock towerRadio cable to dashSide marker lampsTaillight wiring to taillight body studsTurn signal lights on hood scoopUnder dashKeep in mind that not all fasteners found on 1970 Cougars / Mustangs are found in this kit. ...

New bolt for attaching the window guide to the door window bracket on any 1969-70 Mercury Cougar or Ford Mustang with glued in side glass. Two per guide (4 guides per car). 8 total, four on the passenger side, four on the driver side. 1/4"-20 x 5/8" Large Flange Spin Lock Bolt.

Fits standard and XR7 Sold as a Kit as Pictured. Check out this video

These were used to attach the taillight assembly to the tail panel on a 1969-70 Cougar. Five were used per taillight, 10 required in all for one car. Sold individually. Also the same size for 1967-68 tail lights.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

C9ZZ-6503406-A Front windshield lower moulding retainer clips. 7 clips required per car, sold individually.

These studs attached the taillight housing to the tail panel of a 1969-70 Cougar. 6 used per taillight, 12 required per car. Sold individually.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Reproduction body / exterior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Fender Splash Shields (front of fender) Fender Splash Shields (rear of fender) Battery Tray Hood and Hinges Cowl Panel Shock Tower Braces Cowl Braces Hood Latch and Catch Quarter Panel Extensions Trunk Latch...

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Set as Pictured.

Fits Standard and XR7 Sold as a Set as Pictured.

Fits Standard and XR7 with front bumper guards.

These reproduction door hinge bolts are for the Mercury Cougar and Ford Mustang and fit both standard and XR7 Cougar. They are sold in a set of 24.Intended for the 1968-70 hinges that are stamped steel, and not cast iron like 1967 hinges.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Set as Pictured.

Fits Standard and XR7 Sold as a Set as Pictured.

Fits Standard and XR7

Rear Valance Hardware kit contains 2 bolts, 2 clips and 2 nuts. "Almost" correct reproduction that functionally works great. Plated to prevent rust.See related items for a more complete fastener kit, which includes the pan head Phillips screws. Replaces Ford Part #: 372719-s100.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Kit as Pictured.

Sold as a Kit as Pictured.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

Four of these are required to mount the windshield washer motor under the cowl cover of a 1969 - 1970 Mustang or Cougar. Sold individually. # E6AE-17C431

Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.

Complete front and rear bumper mounting hardware for the 1970 Mercury Cougar.

Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

These new taillight mounting washers are sold individually for your Mercury Cougar. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Correct size, style, and color screw for all 1969-70 Mercury Cougar front turn signal bezels. Sold individually, 4 total needed per car.Replaces Ford part number 52445-S.

Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.

Reproduction mounting kit contains everything you need to install the cowl cover on the 69 - 70 Mercury Cougar.

Correct looking mounting plates used to mount the 1970 original spoilers. Comes with all hardware shown, not intended for 1969 spoilers as the use of these requires large rectangular holes, found only on 1970 of the bottom side of the deck lid.

Show quality, correct weight and markings. Sold individually.

This kit mounts the wing to the pedestal.

This kit mounts the spoiler pedestals to the trunk lid. Studs measure 2-3/4" long, correct for the Concours correct stands.Some economy or generic kits come with 1-1/2" studs

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have one or two very small scratches or dings that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

Polished stainless steel inserts that fit in holes around wheel.Fits the following models with style steel wheels:1969 Mercury Cougar1970 Mercury Cougar1969 Mercury Cyclone1970 Mercury CycloneNice used, in most cases we can supply the rubber gaskets, but not always.Limited to stock on hand. ...

Stainless insert that fits in holes around wheel.Fits the following models with styled steel wheels:1969 Mercury Cougar1970 Mercury CougarThese inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not come with...

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have slight blemishes that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

Set of 20 stainless inserts that fit in holes around wheel.Fits the following models with styled steel wheels: 1969 Mercury Cougar1970 Mercury Cougar These inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not...

Click here to view the low resolution version of the power steering illustration from the Ford Master Parts Catalog. If you would like a free copy of the high resolution version, just add it to your cart and you will be given a link to download it on checkout. 

1970 Mercury Cougar Headlight Vacuum DiagramsTo download the full high-resolution version, please add this item to your cart and check out. You will receive a download link automatically. 

This article explains how to switch out the headlight vacuum actuators on the 1967 and 1968 Mercury Cougar in under an hour. Just click "add to cart" and go through checkout, and you'll get a link in your email to download the high resolution version of this article. Check out this video

This is a digital copy of the installation instructions and troubleshooting guide that comes with the 69-73 electronic sequential units that we sell. Click here to view the Low Quality version of this Trouble Shooting Guide. Add it to your cart to download the High Quality version of this Troubleshooting Guide.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Another great free download for you, our customer! In this free download, John Brower guides you through the installation of an overlay on your dashboard on your Mercury. Simply add this item to your cart and you will receive the download link via email after you complete the order.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. Sold individually.Replaces Ford part # 373556-S.

Sold individually. Zinc (dark silver)

Self threading white plastic. Used on front and rear valances.Sold individually.

Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...