All Available Parts - 1968 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 501-600 of 3496
Sorted By:
Availability:
Display Options:
Featured!
Availability: In-Stock Item
Item #: 26148 -
New disc brake proportioning valve / distribution block seal and rebuild kit for the Mercury Cougar or Ford Mustang / Torino. Every 1967-69 Cougar, Cyclone, Torino, Ranchero and Mustang equipped with disc brakes needs this kit even if you are not leaking fluid yet. These little "O" rings are always "rock hard" after 40 plus years because the original O-rings are composed of a BASIC nitrile compound. After several years, the absorption of brake fluid will change the molecular structure of the...
Availability: In-Stock Item
Item #: 11952 -
Reproduction disc brake distribution block and proportioning valve assembly for the Mercury Cougar or Ford Mustang with factory disc brakes. This will also work on your 1968 - 1969 Fairlane / Torino / Montego / Ranchero / Cyclone & Cobra equipped with power disc brakes in the front if you carefully remove the wedged on stamped steel mounting bracket and reuse your original bracket. Mounts to the driver side fender apron with two nuts. With this assembly you will get a distribution block, brake...
Availability: In-Stock Item
Item #: 11953 -
Reproduction proportioning valve for the Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. This valve is most often found at the junction of the high pressure hose back at the rear end, or later, found with the distribution block mounted on the driver side apron (inner fender). Replaces Ford part # C7OZ-2B091-B.Here’s a video to help you rebuild the distribution block and proportioning valve: ...
Availability: In-Stock Item
Item #: 13717 -
Replaces Ford part # C9ZZ-2455-A. Features a longer arm than manual drum brake pedals as it mounts in a different place on the pedal hanger than a manual pedal. Works only with 1969 Bendix booster teardrop shaped power brake booster rod. The pictures below show a correct 1969 only pedal mounted to a 1969 Bendix booster and 1969 only hanger. Look at the pictures closely, many customers have found that their problems are a result of previous owners installing parts from other years. This pedal...
Availability: In-Stock Item
Item #: 13718 -
This pedal comes naked as shown, we highly suggest buying a used original as it will come with correct mounting hardware. Replaces Ford part # C7ZZ-2455-K.
Availability: Used / Wrecking Yard Item
Item #: 24530 -
Longer arm than manual brake pedals. Designed to work with the wider, 1968 collapsible steering column. Will work in 1967 Cougars if converting to 1968 disc brakes. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* On some 1968 Cougars you will have to drill holes in your existing pedal hanger (many are pre-drilled) to accomomdate the power brake pedal. Since systems with a vacuum booster take less effort to activate than systems without, a different folcrum point...
Availability: In-Stock Item
Item #: 11-0417 -
Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.
Availability: In-Stock Item
Item #: 14-0014 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...
Availability: In-Stock Item
Item #: 14-0015 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...
Availability: In-Stock Item
Item #: 14-0033 -
New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...
Availability: In-Stock Item
Item #: 14-0085 -
This charcoal black aerosol paint is a very close match to the original finish used on 1967-68 Cougar XR-7 lower dash structures and steering columns. We've tried it ourselves and have been satisfied with the results. Our only critique is that it's a bit slower to dry than other paints we're used to. The AccuMatch(TM) Interior Paints are the result of years of work and perfectly match the original color shades. Each color has been expertly color-matched. Paints feature extra-high pigment...
Availability: In-Stock Item
Item #: 14-0075 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.
Availability: Out of Stock, On Order
Item #: 14-0077 -
VHT epoxy paint is great for a number of applications. It's a unique one step protective coating that dries quickly and doesn't require a primer. It provides excellent rust, corrosion and chemical resistance which, needless to say, is ideal for anything you're doing under your hood or under and around the body of your car. One can covers about 12 - 14 square feet.
Availability: In-Stock Item
Item #: 14-0090 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...
Availability: In-Stock Item
Item #: 14-0092 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.
Availability: Out of Stock
Item #: 22545 -
Used switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and black knob marked "DEFOG". Replaces Ford part number C8ZZ-18578-A.
Availability: Used / Wrecking Yard Item
Item #: 16745 -
Used service replacement switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and chrome knob, bezel is marked "DEFOG" as shown. *Note - this is not the OEM 1968 defog switch, it is the switch used in defog kits starting in 1970 for many Ford and Mercury dealer installed or over the counter kits.Replaces Ford...
Availability: Out of Stock
Item #: 22952 -
Rear defog conversion kit for any 1968 Mercury Cougar or Ford Mustang Coupe. Includes switch with bracket that goes under the edge of the dash, wiring harness to the accessory plug (for sure on all 1968 Standard and XR7's), long harness to blower motor, and blower motor and grille cover which installs in the rear package tray. Please see your electrical schematic for connection details. Everything has been tested to be in working condition. *NOTE - Early 1967 Cougars do not have the proper...
Availability: Used / Wrecking Yard Item
Item #: 12927 -
Used timing chain cover for any 289 / 302 / 351W engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968 Ford with 289 or 302. Cast aluminum construction without excessive damage. Installation bolt kits also available. Sometime during the 1969 model year, the timing chain cover number changed to C9OE-6059-A. So either one will interchange. Replaces Ford part number C8AE-6059-A.
Availability: In-Stock Item
Item #: 25984 -
Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...
Availability: In-Stock Item
Item #: 26094 -
This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...
Availability: In-Stock Item
Item #: 41791 -
This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.
Availability: In-Stock Item
Item #: 14037 -
This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength. Replaces Ford part # C8ZZ-19A566.
Availability: Used / Wrecking Yard Item
Item #: 11-0019 -
Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...
Availability: Out of Stock
Item #: 13831 -
Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...
Availability: In-Stock Item
Item #: 10523 -
New heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Replaces part # C7ZZ-18591-B.
Availability: Used / Wrecking Yard Item
Item #: 11-0061 -
Used heater blower motor for very late 1967 and all 1968 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. This later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting...
Availability: Used / Wrecking Yard Item
Item #: 11-0109 -
Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0116 -
Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.
Availability: Used / Wrecking Yard Item
Item #: 11-0331 -
Shaft or rod for air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0333 -
Shaft or rod for the evaporator damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...
Availability: Out of Stock
Item #: 11-0336 -
Shaft or rod for the heater damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-B.*Note will not work in 1969-73 A/C boxes.
Availability: Used / Wrecking Yard Item
Item #: 11-0341 -
Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1969-70 brackets, but this one has a slightly shorter and pointed stud. Replaces Ford part number C7ZZ-18A456-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0338 -
Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0340 -
Shaft or rod for the A/C damper blower door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft is clocked differently than the 1969-73 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 11-0344 -
Used rubber elbow that vents air to the blower motor on most 1967 Mercury Cougar and Ford Mustangs with factory air conditioning. At some point in time, this elbow design changed. Easy to tell, this early style connects to a nipple on the fan blower motor. The later version has a hole in the motor case. Not needed with new production fan motors, they don't even have the hole. Replaces Ford part number C7ZA-19A786-B.
Availability: Used / Wrecking Yard Item
Item #: 11-0345 -
Used heater blower motor for 1967 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. Later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is also included. On...
Availability: In-Stock Item
Item #: 12280 -
Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.
Availability: Ships Direct from Supplier (Except International)
Item #: 41955 -
Heater Box Assembly for 1967-1968 Mustangs without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a factory type fiberglass two piece heater box/heater core casing. The heater box is a pre-assembled unit which includes the gasket and all seals. The heater plenum attaches to this assembly and directs warm air to the car. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts...
Availability: In-Stock Item
Item #: 41405 -
Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...
Availability: In-Stock Item
Item #: 10479 -
Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.
Availability: In-Stock Item
Item #: 10534 -
These reproduction pieces are factory correct replacements for your 1967-68 Cougar or Mustang and will only fit non A/C heater cores of those years.
Availability: Used / Wrecking Yard Item
Item #: 11-0139 -
Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...
Availability: Used / Wrecking Yard Item
Item #: 11-0290 -
Metal fan wheel or squirrel cage for any 1967-68 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-1/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Availability: Used / Wrecking Yard Item
Item #: 11-0289 -
Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Availability: Used / Wrecking Yard Item
Item #: 11-0384 -
Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1967-68 Mercury Cougar and 1965-68 Ford Mustang.Ford part # C2OA-18591-A or C8ZZ-18591-A*Note - Excludes Heater with integral or factory air conditioning.
Availability: In-Stock Item
Item #: 11-4000 -
Good used working original heater blower motor for 67 - 68 Mercury Cougar and Ford Mustang. The reproduction off-shore units may or may not prove to be as good of value as these good used original FoMoCo motors. Keep in mind our used units carry a one year warranty and the new off-shore motors only have a 30 day warranty. Also know that the mounting plate is included for free just by asking on the used motors. We never use the reproductions here at WCCC. This unit...
Availability: In-Stock Item
Item #: 11-4002 -
Used mounting plate for the heater blower motor on the 67 - 68 Cougar or Mustang without A/C.
Availability: In-Stock Item
Item #: 14364 -
Reproduction heater cable set for your beloved Cat or Pony. This set is an exact fit! Replaces Ford part # C7ZZ-18518-A. *Customer Feedback* "My first deal with Don was clear back in the 1980's and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you...
Availability: In-Stock Item
Item #: 13765 -
For us with Cougars without factory AC. The originals were made of cardboard and are very prone to failure from moisture. These are made from virgin ABS black plastic and are excellent quality in every respect. Not often does a reproduction come along that blows away OEM, but this definitely is that part. Before you finish making your online order with us, go look at your plenum to see what condition your original is in. Replaces Ford part #: C5ZZ-18471-A
Availability: In-Stock Item
Item #: 13947 -
This reproduction knob set is made by Scott Drake Enterprises. Unlike original knobs, these have a much larger font. Much easier to read while driving than the originals. Replaces Ford Part #: C8ZZ-18519
Availability: Used / Wrecking Yard Item
Item #: 11-0021 -
Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B
Availability: In-Stock Item
Item #: 41508 -
Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C8ZZ-18578-B.
Availability: Used / Wrecking Yard Item
Item #: 11-0059 -
These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing.Ford part # C7ZZ-6501891.
Availability: Out of Stock
Item #: 33118 -
Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. New Old Stock switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B
Availability: In-Stock Item
Item #: 13770 -
This is the non-concours window regulator that many dealers carry. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!
Availability: In-Stock Item
Item #: 13768 -
This is the non-concours window regulator that many dealers carry.
Availability: Used / Wrecking Yard Item
Item #: 20637 -
Used driver side (left hand) grade "A" clear vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. This vent window glass often comes with a frame and...
Availability: Used / Wrecking Yard Item
Item #: 20640 -
Used grade "A" clear passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521412-C. *NOTE* Air...
Availability: Used / Wrecking Yard Item
Item #: 11-0141 -
22954 Door vent window pivot bracket, mounts to the bottom of the vent window assembly on a 1967-68 Mercury Cougar or Ford Mustang. Right and left side brackets interchange.
Availability: Used / Wrecking Yard Item
Item #: 11-0162 -
22992 "D" shaped top washer, Ford called it a 'stop'. See assembly picture. 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side, sold individually.
Availability: Used / Wrecking Yard Item
Item #: 11-0161 -
22992 SPRING Tension spring for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.
Availability: Used / Wrecking Yard Item
Item #: 11-0144 -
34392-S7 5/16 inch nut for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.
Availability: Used / Wrecking Yard Item
Item #: 11-0143 -
375897-S White plastic 5/16" washer for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 2 per side, sold individually.
Availability: Used / Wrecking Yard Item
Item #: 11-0163 -
C2AZ-22963-A Special steel flat washer with flat sides for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.
Availability: Used / Wrecking Yard Item
Item #: 11-0211 -
Used grade B stainless steel vent window glass frame for the right side or passenger side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967, with the exception of the length of the stud for the knob. Shipped bare, no glass or hardware.Ford part # C8ZZ-6521608-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0209 -
Used grade B stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967, with the exception of the length of the stud for the knob. Shipped bare, no glass or hardware.Ford part # C8ZZ-6521609-A.
Availability: Used / Wrecking Yard Item
Item #: 15717 -
Used driver side (left hand) vent window frame as it comes out of the door. This unit is just the bare window frame and will need some cleaning as it is 40 plus years old. A great option for those of you who have a limited budget. Also, because this is an original piece, it will have a far superior fit and function than the "off shore" reproductions that are currently offered. Ford part # C7ZZ-6522205-A. *Note* "B" grade will have some pitting in the chrome on the interior side of the...
Availability: In-Stock Item
Item #: 10535 -
Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183
Availability: Ships Direct from Supplier (Except International)
Item #: 15414 -
Reproduction driver side (left hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option that...
Availability: Ships Direct from Supplier (Except International)
Item #: 10184 -
Reproduction green tinted driver side (left hand) vent window glass for the Mercury Cougar or Ford Mustang. If your car has factory integral air conditioning, it came with green tinted glass that was called "Sun-X" tint. This is an excellent replacement piece and is just a the bare piece of glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few...
Availability: In-Stock Item
Item #: 30102 -
Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.
Availability: Used / Wrecking Yard Item
Item #: 11-0372 -
Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...
Availability: In-Stock Item
Item #: 11-0385 -
Air conditioning fan blower assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.
Availability: In-Stock Item
Item #: 26197 -
Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.
Availability: Used / Wrecking Yard Item
Item #: 11-0447 -
Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...
Availability: In-Stock Item
Item #: 11-0448 -
Used mounting bracket from a 1967-68 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket.
Availability: In-Stock Item
Item #: 32255 -
Premium reproduction rubber grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Molded rubber exactly like the original! Other reproductions on the market are die cut from sponge rubber sheets and nothing like the original. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years. ...
Availability: In-Stock Item
Item #: 11-0469 -
Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. There are a couple of versions of this housing. There is a version with a cooling nipple for cooling the...
Availability: In-Stock Item
Item #: 11-0472 -
Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version. There are a couple of versions of this housing. There is a version with a...
Availability: Used / Wrecking Yard Item
Item #: 11-0475 -
Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...
Availability: In-Stock Item
Item #: 11-0510 -
Used extension or rod for the vacuum actuator for controlling dampers and levers on the 1967-68 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 1-15/16 inches long. For 1967-68 Cougar and Mustang, all three vacuum actuators used this same length extension. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C7ZA-18A318-A....
Availability: In-Stock Item
Item #: 18740 -
Used heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Ford part # C7ZZ-18591-B.
Availability: Used / Wrecking Yard Item
Item #: 20032 -
This 1967-68 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390-427-428's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...
Availability: In-Stock Item
Item #: 41704 -
Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.
Availability: In-Stock Item
Item #: 11998 -
Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.
Availability: In-Stock Item
Item #: 12333 -
Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.
Availability: Ships Direct from Supplier (Except International)
Item #: 47896 -
Usually ships in 3-5 business days. Reproduction heater box with A/C for 67 - 68 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). See related products.
The style of this box most resembles the 1967 version, with the flat mating surfaces between the two...
Availability: Used / Wrecking Yard Item
Item #: 11-0326 -
Air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1969-73 door, but without a small notch. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...
Availability: Used / Wrecking Yard Item
Item #: 11-0329 -
Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...
Availability: In-Stock Item
Item #: 26156 -
Concours correct red striped heater hose for late 1968 (after 2/1/1968) Mercury Cougar and Ford Mustang. Durable red striping with "Autolite" spelled out and dated H8A23B. Correct for all V-8 engines without air conditioning. The difference with the 'with air conditioning' hoses is they have a molded 90 degree elbow. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the red striping shows!
Availability: In-Stock Item
Item #: 11364 -
Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. Correct for all V-8 engines without air conditioning. The Cougars and Mustangs with air conditioning have a molded 90 degree elbow at one end. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the white striping shows!
Availability: In-Stock Item
Item #: 41585 -
This direct replacement resistor is used between the heater switch and the blower motor. These often fail and prevent the blower motor from turning on. Replaces Ford part # C2OA-18591-A. 1962 - 1967 Ford Fairlane1962 - 1964 Ford Galaxie1964 - 1966 Ford Thunderbird 1967 Ford Mustang 1968 Ford Mustang ...
Availability: In-Stock Item
Item #: 25987 -
Constructed from corrosion resistant copper and brass. A great buy for anyone needing to make repairs to this vital part. Replaces Ford Part #: C5DZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...
Availability: Ships Direct from Supplier (Except International)
Item #: 26914 -
Reproduction Passenger side (right hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option...
Availability: Used / Wrecking Yard Item
Item #: 11-0142 -
Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. This unit will have all three window stops and both window guides still attached. Ford part # C7ZZ-6529753-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Used / Wrecking Yard Item
Item #: 11-0250 -
Good used passenger side (right hand) quarter window guide for the Mercury Cougar or Ford Mustang. This unit will have all three window stops and both window guides still attached. Ford part # C7ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Used / Wrecking Yard Item
Item #: 11-0164 -
C5ZZ-6529968-A two of these window stop brackets mount to each of the quarter window frames. Bracket for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side. Casting # is C4ZB-65298A22-ASold individually, two per side, 4 per car.
Availability: Used / Wrecking Yard Item
Item #: 12043 -
Used driver side (left hand) grade "A" green tinted vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars or Mustangs came with this SUN-X tinted glass if they were factory equipped with A/C. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Ford part #...
Availability: Used / Wrecking Yard Item
Item #: 12044 -
Used grade "A" tinted passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars and Mustangs came with this green tinted SUN-X glass if they were also equipped with A/C from the factory. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro....