All Available Parts - 1968 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 3101-3200 of 3496
Sorted By:
Availability:
Display Options:
Availability: Out of Stock, On Order
Item #: 41857 -
Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...
Availability: Out of Stock
Item #: 31725 -
Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.
Availability: Out of Stock
Item #: 10941 -
Nice rebuildable core of the Carter X 4441S fuel pump for all 1968-70 428 Cobra Jet engines. Has "X" casting, 4441S stamped, dated 10B9A, February 10, 1969. Kits available for rebuilding.
Availability: Out of Stock
Item #: 12439 -
Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.
Availability: Out of Stock
Item #: 20209 -
Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.
Availability: Out of Stock
Item #: 14275 -
Used plastic clip for the Mercury Cougar or Ford Mustang.
Availability: Out of Stock, On Order
Item #: 14260 -
Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.
Availability: Out of Stock
Item #: 33440 -
Dual vacuum advance stamped with HP6. Original for 1968-69 428 Cobra Jet distributor with 4 speed. The outer nipple does work. Brass nipples in very good condition. Ford part number C8AZ-12370-E.
Availability: Out of Stock
Item #: 33537 -
If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970. Ford part # C9AZ-9H576-A.
Availability: Out of Stock
Item #: 20160 -
Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.
Availability: Out of Stock
Item #: 31562 -
Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.
Availability: Out of Stock
Item #: 33328 -
New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...
Availability: Out of Stock, Discontinued
Item #: 32280 -
Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port to add a nipple. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later vacuum advances had...
Availability: Out of Stock
Item #: 32282 -
Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...
Availability: Out of Stock
Item #: 20159 -
OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang
Availability: Out of Stock
Item #: 24084 -
C7TE-9425-G Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used before 1-9-1968. Take off manifold with correct casting number of C7TE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-P. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...
Availability: Out of Stock
Item #: 24460 -
C8TE-9425-A Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used after 1-9-1968. Take off manifold with correct casting number of C8TE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-R. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...
Availability: Out of Stock
Item #: 30288 -
Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and 1970 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy demand...
Availability: Out of Stock
Item #: 30119 -
Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.
Availability: Out of Stock
Item #: 11302 -
Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...
Availability: Out of Stock
Item #: 41415 -
This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...
Availability: Out of Stock
Item #: 53267 -
Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.
Availability: Out of Stock, On Order
Item #: 53266 -
Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.
Availability: Out of Stock, On Order
Item #: 53269 -
Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.
Availability: Out of Stock
Item #: 32981 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 5L18, November 18, 1965. Used 0.030 over bore 4.180" Ford 428 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...
Availability: Out of Stock
Item #: 24517 -
Used Distributor / 302-4V / Manual Transmission for the 1968 Mercury Cougar / 1968 Ford MustangFord part number C8ZF-12127-A
Availability: Out of Stock
Item #: 24518 -
Used Distributor / 302-4V / Automatic Transmission for the 1968 Mercury Cougar / 1968 Ford MustangFord part number C8ZF-12127-B
Availability: Used / Wrecking Yard Item
Item #: 32246 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 7M16 or December 16, 1967. This item cannot ship through...
Availability: Out of Stock
Item #: 32308 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 6K4 or October 4, 1966. This item cannot ship...
Availability: Out of Stock
Item #: 32307 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 7l17 or November 17, 1967. This item cannot ship through any...
Availability: Out of Stock
Item #: 32957 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7L1, November 1, 1967. Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. This item cannot ship...
Availability: Out of Stock
Item #: 32958 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 8B1, February 1, 1968. Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. This item cannot ship...
Featured!
Availability: Out of Stock
Item #: 30308 -
Featured in this kit are all the basic items you need to convert your small block 1967 - 1968 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan. This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs. This might sound like overkill for your small...
Availability: Out of Stock
Item #: 11292 -
Used on the ignition lock cylinder. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang.
Availability: Out of Stock, On Order
Item #: 10044 -
This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...
Availability: Out of Stock
Item #: 31449 -
Used Bracket for mounting the Servo on any 1967-68 Mercury Cougar or Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C736-A.
Availability: Out of Stock, On Order
Item #: 41586 -
Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 30826 -
Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69. Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...
Availability: Out of Stock
Item #: 30807 -
Original OEM light found on early cars and later recalled. EXACTLY 100% correct with the right serial numbers in the right places as per the blueprints from Shelby American: * IGM 1642 PN on the bottom right * K11123 N14 cm AUF 5m up the right side * No numbers on left side Marchal made several versions of this light, only this one is the correct one for your Mustang. It has the famous 'cat eyes' internal diffuser. Reproduction lights use a different bulb, lack the diffuser and have the word...
Availability: Out of Stock, On Order
Item #: 10637 -
1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.
Availability: Out of Stock
Item #: 11347 -
Oil pressure sending unit 1967-68 Mercury Cougar and Ford Mustang 289/302 oil warning light style. This part actually goes back to 1956. Used on various Ford and Mercury engines from 1956-68. Clip on style wiring harness should be verified prior to purchase. *Note - Not for XR7Check out the video below on our new gauge tester: ...
Availability: Out of Stock, On Order
Item #: 11349 -
Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...
Availability: Out of Stock
Item #: 16002 -
Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.
Availability: Out of Stock
Item #: 26427 -
Reproduction 390 4V GT Emission Decal for the 1968 and 1969 Mercury Cougar / Ford Mustang
Availability: Out of Stock, Discontinued
Item #: 26366 -
Replica of the Autolite battery Stay-Ful tag advertising that the batteries 'Need water only 3 times a year'.
Availability: Out of Stock, Discontinued
Item #: 26257 -
Reproduction 289 / 302 2V AT / MT Emission Decal for the 1968 Mercury Cougar or Ford Mustang
Availability: Out of Stock
Item #: 41982 -
Reproduction front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. These are made just like the originals, are concours correct and includes the firewall seal and firewall bracket. Replaces Ford part # C7ZZ-2853-A.
Availability: Out of Stock
Item #: 13609 -
This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...
Availability: Out of Stock
Item #: 26091 -
This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.
Availability: Out of Stock, On Order
Item #: 26487 -
Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.
Availability: Out of Stock, On Order
Item #: 13691 -
New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...
Availability: Out of Stock, On Order
Item #: 12337 -
New front inner wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.25 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...
Availability: Out of Stock
Item #: 27582 -
NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.
Availability: Out of Stock, On Order
Item #: 30403 -
Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...
Availability: Out of Stock
Item #: 30402 -
Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...
Availability: Out of Stock
Item #: 31945 -
Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...
Availability: Out of Stock
Item #: 24257 -
Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.
Availability: Out of Stock, On Order
Item #: 19943 -
This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.
Availability: Out of Stock, On Order
Item #: 13945 -
This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.
Availability: Out of Stock
Item #: 14-0012 -
4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Out of Stock
Item #: 14956 -
This kit contains all the replacement springs and hold down components required to do a professional job on rear drum brakes. Kit includes enough parts for two wheels. This is for the 9 inch drum brakes commonly found on the early 6 cylinder cars with 7-1/4 inch rear ends.*Note - Kit does not include hardware for rear emergency brakes.
Availability: Out of Stock
Item #: 33095 -
NOS brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.
Availability: Out of Stock
Item #: 24617 -
C9OZ-2211-C Right hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70866. Originally manufactured by Bendix part number 319481.
Availability: Out of Stock
Item #: 24619 -
C9OZ-2212-C Left hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70867. Originally manufactured by Bendix part number 319480.
Availability: Out of Stock
Item #: 23816 -
C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.
Availability: Out of Stock
Item #: 24616 -
C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.
Availability: Out of Stock
Item #: 24618 -
C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..
Availability: Out of Stock
Item #: 13680 -
Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.
Availability: Out of Stock
Item #: 17-0002 -
This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...
Availability: Out of Stock
Item #: 26878 -
Pair of reproduction firewall to shock tower braces for the Mercury Cougar. These are good quality reproductions that are already painted black so the only thing you need to do is bolt them on.Replaces Ford part #'s C7ZZ-16A053 driver side (left hand), C7ZZ-16A052 passenger side (right hand).
Availability: Out of Stock, On Order
Item #: 12474 -
Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.
Availability: Out of Stock
Item #: 12476 -
Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.
Availability: Out of Stock, On Order
Item #: 14173 -
Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.
Availability: Out of Stock
Item #: 13728 -
Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!
Availability: Out of Stock
Item #: 20151 -
Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!
Availability: Out of Stock
Item #: 19280 -
This tower is identical to every other 1967-70 tower in every way except the reinforcement plate. In late 1968 390-427-428 Mercury Cougar and Ford Mustang came with this reinforced tower due to a problem they were having with structural cracking. No specific part number for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...
Availability: Out of Stock
Item #: 23487 -
Reproduction shock tower and apron assembly for your Cat or Pony.Here's a little film to help you fortify your flexxy feline!
Availability: Out of Stock
Item #: 20152 -
Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.
Availability: Out of Stock
Item #: 13729 -
Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!
Availability: Out of Stock
Item #: 19241 -
This tower is identical to every other 1967-70 tower in every way except the reinforcement plate.The reinforced shock towers came out in late March 1968 and were used on all big block Cougars and Mustangs. 390-2V / 390-4V / 427 / 428CJ. No specific part number exists for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...
Availability: Out of Stock
Item #: 42392 -
Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Availability: Out of Stock
Item #: 42393 -
Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Availability: Out of Stock, On Order
Item #: 12455 -
New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.
Availability: Out of Stock
Item #: 10932 -
New inner floor frame support for the Mercury Cougar and Ford Mustang.
Availability: Out of Stock, On Order
Item #: 15492 -
Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.
Availability: Out of Stock, On Order
Item #: 15493 -
Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.
Availability: Out of Stock
Item #: 42390 -
Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Availability: Out of Stock, On Order
Item #: 42399 -
Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.
Featured!
Availability: Out of Stock
Item #: 31836 -
Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...
Availability: Out of Stock, On Order
Item #: 11685 -
* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....
Availability: Out of Stock, On Order
Item #: 14301 -
Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...
Availability: Out of Stock
Item #: 20149 -
Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....
Availability: Out of Stock
Item #: 31304 -
Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.
Availability: Out of Stock
Item #: 42380 -
Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...
Availability: Out of Stock
Item #: 42381 -
Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...
Availability: Out of Stock
Item #: 14567 -
If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.
We carefully inspect these hinges before sending them...
Availability: Out of Stock
Item #: 14566 -
If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.
We carefully inspect these hinges before sending them...
Availability: In-Stock Item
Item #: 23892 -
C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.
Availability: Out of Stock
Item #: 20527 -
Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...
Availability: Out of Stock
Item #: 24447 -
C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.