All Available Parts - 1968 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 501-600 of 3443
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 30102 -
Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.
Availability: Used / Wrecking Yard Item
Item #: 11-0372 -
Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...
Availability: In-Stock Item
Item #: 11-0385 -
Air conditioning fan blower assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.
Availability: In-Stock Item
Item #: 26197 -
Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.
Availability: Used / Wrecking Yard Item
Item #: 11-0447 -
Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...
Availability: In-Stock Item
Item #: 11-0448 -
Used mounting bracket from a 1967-68 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket.
Availability: In-Stock Item
Item #: 32255 -
Premium reproduction rubber grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Molded rubber exactly like the original! Other reproductions on the market are die cut from sponge rubber sheets and nothing like the original. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years. ...
Availability: In-Stock Item
Item #: 11-0469 -
Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. There are a couple of versions of this housing. There is a version with a cooling nipple for cooling the...
Availability: In-Stock Item
Item #: 11-0472 -
Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version. There are a couple of versions of this housing. There is a version with a...
Availability: Used / Wrecking Yard Item
Item #: 11-0475 -
Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...
Availability: In-Stock Item
Item #: 11-0510 -
Used extension or rod for the vacuum actuator for controlling dampers and levers on the 1967-68 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 1-15/16 inches long. For 1967-68 Cougar and Mustang, all three vacuum actuators used this same length extension. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C7ZA-18A318-A....
Availability: In-Stock Item
Item #: 18740 -
Used heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Ford part # C7ZZ-18591-B.
Availability: Used / Wrecking Yard Item
Item #: 20032 -
This 1967-68 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390-427-428's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...
Availability: In-Stock Item
Item #: 41704 -
Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.
Availability: In-Stock Item
Item #: 41791 -
This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.
Availability: In-Stock Item
Item #: 14037 -
This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength. Replaces Ford part # C8ZZ-19A566.
Availability: Used / Wrecking Yard Item
Item #: 11-0019 -
Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...
Availability: Out of Stock
Item #: 13831 -
Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...
Availability: In-Stock Item
Item #: 10523 -
New heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Replaces part # C7ZZ-18591-B.
Availability: Used / Wrecking Yard Item
Item #: 11-0061 -
Used heater blower motor for very late 1967 and all 1968 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. This later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting...
Availability: Used / Wrecking Yard Item
Item #: 11-0109 -
Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0116 -
Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.
Availability: In-Stock Item
Item #: 11998 -
Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.
Availability: In-Stock Item
Item #: 12333 -
Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.
Availability: Ships Direct from Supplier (Except International)
Item #: 47896 -
Usually ships in 3-5 business days. Reproduction heater box with A/C for 67 - 68 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). See related products.
The style of this box most resembles the 1967 version, with the flat mating surfaces between the two...
Availability: Used / Wrecking Yard Item
Item #: 11-0326 -
Air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1969-73 door, but without a small notch. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...
Availability: Used / Wrecking Yard Item
Item #: 11-0329 -
Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...
Availability: In-Stock Item
Item #: 26156 -
Concours correct red striped heater hose for late 1968 (after 2/1/1968) Mercury Cougar and Ford Mustang. Durable red striping with "Autolite" spelled out and dated H8A23B. Correct for all V-8 engines without air conditioning. The difference with the 'with air conditioning' hoses is they have a molded 90 degree elbow. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the red striping shows!
Availability: In-Stock Item
Item #: 11364 -
Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. Correct for all V-8 engines without air conditioning. The Cougars and Mustangs with air conditioning have a molded 90 degree elbow at one end. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the white striping shows!
Availability: In-Stock Item
Item #: 41585 -
This direct replacement resistor is used between the heater switch and the blower motor. These often fail and prevent the blower motor from turning on. Replaces Ford part # C2OA-18591-A. 1962 - 1967 Ford Fairlane1962 - 1964 Ford Galaxie1964 - 1966 Ford Thunderbird 1967 Ford Mustang 1968 Ford Mustang ...
Availability: In-Stock Item
Item #: 25987 -
Constructed from corrosion resistant copper and brass. A great buy for anyone needing to make repairs to this vital part. Replaces Ford Part #: C5DZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...
Availability: Ships Direct from Supplier (Except International)
Item #: 41955 -
Heater Box Assembly for 1967-1968 Mustangs without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a factory type fiberglass two piece heater box/heater core casing. The heater box is a pre-assembled unit which includes the gasket and all seals. The heater plenum attaches to this assembly and directs warm air to the car. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts...
Availability: In-Stock Item
Item #: 41405 -
Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...
Availability: In-Stock Item
Item #: 10479 -
Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.
Availability: In-Stock Item
Item #: 10534 -
These reproduction pieces are factory correct replacements for your 1967-68 Cougar or Mustang and will only fit non A/C heater cores of those years.
Availability: Used / Wrecking Yard Item
Item #: 11-0139 -
Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...
Availability: Used / Wrecking Yard Item
Item #: 11-0290 -
Metal fan wheel or squirrel cage for any 1967-68 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-1/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Availability: Used / Wrecking Yard Item
Item #: 11-0289 -
Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Availability: Used / Wrecking Yard Item
Item #: 11-0384 -
Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1967-68 Mercury Cougar and 1965-68 Ford Mustang.Ford part # C2OA-18591-A or C8ZZ-18591-A*Note - Excludes Heater with integral or factory air conditioning.
Availability: In-Stock Item
Item #: 11-4000 -
Good used working original heater blower motor for 67 - 68 Mercury Cougar and Ford Mustang. The reproduction off-shore units may or may not prove to be as good of value as these good used original FoMoCo motors. Keep in mind our used units carry a one year warranty and the new off-shore motors only have a 30 day warranty. Also know that the mounting plate is included for free just by asking on the used motors. We never use the reproductions here at WCCC. This unit...
Availability: In-Stock Item
Item #: 11-4002 -
Used mounting plate for the heater blower motor on the 67 - 68 Cougar or Mustang without A/C.
Availability: In-Stock Item
Item #: 14364 -
Reproduction heater cable set for your beloved Cat or Pony. This set is an exact fit! Replaces Ford part # C7ZZ-18518-A. *Customer Feedback* "My first deal with Don was clear back in the 1980's and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you...
Availability: In-Stock Item
Item #: 13765 -
For us with Cougars without factory AC. The originals were made of cardboard and are very prone to failure from moisture. These are made from virgin ABS black plastic and are excellent quality in every respect. Not often does a reproduction come along that blows away OEM, but this definitely is that part. Before you finish making your online order with us, go look at your plenum to see what condition your original is in. Replaces Ford part #: C5ZZ-18471-A
Availability: In-Stock Item
Item #: 13947 -
This reproduction knob set is made by Scott Drake Enterprises. Unlike original knobs, these have a much larger font. Much easier to read while driving than the originals. Replaces Ford Part #: C8ZZ-18519
Availability: Used / Wrecking Yard Item
Item #: 11-0021 -
Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B
Availability: In-Stock Item
Item #: 41508 -
Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C8ZZ-18578-B.
Availability: Used / Wrecking Yard Item
Item #: 11-0059 -
These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing.Ford part # C7ZZ-6501891.
Availability: Out of Stock
Item #: 33118 -
Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. New Old Stock switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B
Availability: In-Stock Item
Item #: 13770 -
This is the non-concours window regulator that many dealers carry.Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video
Availability: In-Stock Item
Item #: 13768 -
This is the non-concours window regulator that many dealers carry.
Availability: Used / Wrecking Yard Item
Item #: 20637 -
Used driver side (left hand) grade "A" clear vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.This vent window glass often comes with a frame and...
Availability: Used / Wrecking Yard Item
Item #: 20640 -
Used grade "A" clear passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521412-C. *NOTE* Air...
Availability: Used / Wrecking Yard Item
Item #: 11-0141 -
22954 Door vent window pivot bracket
Availability: Used / Wrecking Yard Item
Item #: 11-0162 -
22992 "D" shaped top washer, Ford called it a 'stop'. See assembly picture. 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side, sold individually.
Availability: Used / Wrecking Yard Item
Item #: 11-0161 -
22992 SPRING Tension spring for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.
Availability: Used / Wrecking Yard Item
Item #: 11-0144 -
34392-S7 5/16 inch nut for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.
Availability: Used / Wrecking Yard Item
Item #: 11-0143 -
375897-S White plastic 5/16" washer for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 2 per side, sold individually.
Availability: Used / Wrecking Yard Item
Item #: 11-0163 -
C2AZ-22963-A Special steel flat washer with flat sides for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.
Availability: Used / Wrecking Yard Item
Item #: 11-0211 -
Used grade B stainless steel vent window glass frame for the right side or passenger side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967
Availability: Used / Wrecking Yard Item
Item #: 11-0209 -
Used grade B stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967
Availability: Used / Wrecking Yard Item
Item #: 15717 -
Used driver side (left hand) vent window frame as it comes out of thedoor. This unit is just the bare window frame and will need some cleaning as itis 40 plus years old. A great option for those of you who have a limited budget. Also, because this is an original piece, it will have a far superior fit and function than the"off shore" reproductions that are currently offered.Ford part # C7ZZ-6522205-A.*Note* "B" grade will have some pitting in the chrome on theinterior side of the frame. Check...
Availability: In-Stock Item
Item #: 10535 -
Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183
Availability: Ships Direct from Supplier (Except International)
Item #: 15414 -
Reproduction driver side (left hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option that...
Availability: Ships Direct from Supplier (Except International)
Item #: 10184 -
Reproduction green tinted driver side (left hand) vent window glass for the Mercury Cougar or Ford Mustang. If your car has factory integral air conditioning, it came with green tinted glass that was called "Sun-X" tint. This is an excellent replacement piece and is just a the bare piece of glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few...
Availability: Used / Wrecking Yard Item
Item #: 15720 -
Used grade "A" passenger side (right hand) vent window frame as it comes out of the door and is just the bare window frame. This is not a perfect part but it will look good on a low mile car that shows a little patina. The weatherstrip track that continues down into the door can be had with this part for no extra charge, please mention it in the comments section when you order online. Ford part # C7ZZ-6522204-A. Casting # C7ZB-6522222-ACheck out our video below for helpful tips on...
Availability: Ships Direct from Supplier (Except International)
Item #: 26914 -
Reproduction Passenger side (right hand) clear door vent glass for the Mercury Cougar or Ford Mustang. There are three versions of this piece of glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint option...
Availability: Used / Wrecking Yard Item
Item #: 11-0142 -
Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade B will have some rust or erosion from moisture, missing zinc plating. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529753-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...
Availability: Used / Wrecking Yard Item
Item #: 11-0250 -
Good used passenger side (right hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade B will have some rust or erosion from moisture, missing zinc plating. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...
Availability: Used / Wrecking Yard Item
Item #: 11-0164 -
C5ZZ-6529968-A two of these window stop brackets mount to each of the quarter window frames. Bracket for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side. Casting # is C4ZB-65298A22-ASold individually
Availability: Used / Wrecking Yard Item
Item #: 12043 -
Used driver side (left hand) grade "A" green tinted vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars or Mustangs came with this SUN-X tinted glass if they were factory equipped with A/C. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part #...
Availability: Used / Wrecking Yard Item
Item #: 12044 -
Used grade "A" tinted passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars and Mustangs came with this green tinted SUN-X glass if they were also equipped with A/C from the factory. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than...
Availability: Used / Wrecking Yard Item
Item #: 11-0151 -
Good used original FORD part that has been closely inspected for rust on the roller shaft / stud and bent arms. 1967 & 1968 units will have new rollers included. We are of the opinion that these are better quality than the off shore reproductions that are available. With a little elbow grease this good quality originals will have years of good service left in them. Unlike the reproductions these come with a one year warranty. Ford Part Numbers: C5ZZ-6530306-A, C5ZZ-6530307-A,...
Availability: Used / Wrecking Yard Item
Item #: 11-0156 -
1968 Passenger / Right Hand Regulator pictured (Part #: C8ZZ-6530307-A). Good used original FORD part that has been closely inspected for rust on the roller shaft / stud and bent arms. 1967 & 1968 units will have new rollers included. We are of the opinion that these are better quality than the off shore reproductions that are available. With a little elbow grease this good quality originals will have years of good service left in them.This 1968 regulator has a slightly shorter window crank...
Availability: Used / Wrecking Yard Item
Item #: 11-0286 -
Used roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Also found on all 1967-68 Mercury Cougar and Ford Mustang door window channels. Often times one of the rollers breaks off and allows chattering of the window movement. Sold individually: 3 total rollers on each side of the quarter window brackets. 2 like this
Availability: Used / Wrecking Yard Item
Item #: 11-0287 -
Used single plastic roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Note that there is only one of this style of roller on each quarter window. This is a simple white plastic roller and a rivet. Note that there are 2 rollers with 2 pieces of round white plastic. Often times one of the rollers breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the...
Availability: Used / Wrecking Yard Item
Item #: 11-0306 -
Used bracket for mounting the bottom of the quarter window guide to the car body. Fits all 1967-68 Mercury Cougar and 1966-68 Ford Mustang coupe and convertible (non fastback). "L" shaped bracket that designed for mounting and adjusting the rear quarter window.Replaces Ford part number C6ZB-6529778.
Availability: Used / Wrecking Yard Item
Item #: 11-0370 -
Passenger side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.
Availability: Used / Wrecking Yard Item
Item #: 11-0371 -
Driver side quarter window slide. This is the 10 1/2" slide that bolts to the inner body of the quarter window area.
Availability: In-Stock Item
Item #: 30516 -
Reproduction of the very hard to find window roller for the window channel / quarter window frame on the 67 - 68 Cougar and Mustang. Doubles as both the single and double type roller (with the included support washer).Included in this kit are: One roller, one rivet, one wavy washer, one flat washer, and one support washer, measures exactly 1" wide. Rivet is for a 1/4" hole.2 required per door glass channel, 3 per quarter window frame.Sold individually. Replaces Ford Part # C8SZ-57262A32-A....
Availability: In-Stock Item
Item #: 11-0397 -
Stop bracket for the rear quarter window regulator on any 1967-68 Mercury Cougar and 1965-68 Ford Mustang Coupe and convertible models. Stop bracket for the quarter window regulator arm. Comes with used bolt as shown. One bracket per side, same bracket for driver or passenger side.Reproduction also available.Ford part number C4ZB-65303A12 also referenced as 29822 in the assembly manuals. ...
Availability: In-Stock Item
Item #: 32220 -
Reproduction Quarter window stops. Mounts onto quarter window to limit upward travel within the channel. Each quarter window requires two of these stops. Fits either driver side or passenger side quarter window. For Coupe or (Mustang) Convertible body styles. Bolt included.Replaces Ford Part # C5ZZ-6529968-A Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video below: Window Regulator Replacement - 1967-68 Cougar / Mustang Check out...
Availability: Used / Wrecking Yard Item
Item #: 11-0502 -
Used grade A stainless steel vent window glass frame for the right side or passenger side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967
Availability: Used / Wrecking Yard Item
Item #: 32399 -
Used grade "B" tinted passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars and Mustangs came with this green tinted SUN-X glass if they were also equipped with A/C from the factory. Good used door glass with a few scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than...
Availability: Used / Wrecking Yard Item
Item #: 32397 -
Used driver side (left hand) grade "B" clear vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with some scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521413-C. *NOTE* Air conditioning cars were...
Availability: Used / Wrecking Yard Item
Item #: 32400 -
Used grade "B" clear passenger side (right hand) door vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521412-C. *NOTE* Air conditioning cars...
Availability: Used / Wrecking Yard Item
Item #: 32398 -
Used driver side (left hand) grade "B" green tinted vent window glass for the Mercury Cougar or Ford Mustang coupe or convertible. All Cougars or Mustangs came with this SUN-X tinted glass if they were factory equipped with A/C. Good used door glass with some scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part # C5ZZ-6521413-D....
Availability: In-Stock Item
Item #: 11-0508 -
Restored stainless steel vent window glass frame for the right side or passenger side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges
Availability: In-Stock Item
Item #: 11-0509 -
Restored stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges
Availability: In-Stock Item
Item #: 32910 -
Reproduction stop bracket for the rear quarter window regulator on any 1967-68 Mercury Cougar and 1965-68 Ford Mustang Coupe and convertible models. Stop bracket for the quarter window regulator arm. Comes with used bolt as shown. One bracket per side, same bracket for driver or passenger side.Replaces Ford part number C4ZB-65303A12 also referenced as 29822 in the assembly manuals.Also available used. ...
Availability: In-Stock Item
Item #: 32582 -
Clevis and hairpin assembly for parking brake on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Replacement pin for the cable wheel on the emergency hand brake.
Availability: In-Stock Item
Item #: 32358 -
Reproduction batter bracket or clamp for battery installation. "L" bracket attaches to the battery apron and steps down for the battery hold down clamp. Not sure which cars got this, but likely was for the larger sized battery. Fits 1967-68 Cougar and Mustang including Shelby Mustang. USA made preproduction part.
Availability: In-Stock Item
Item #: 32947 -
Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.
Availability: In-Stock Item
Item #: 32395 -
New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3.
Availability: In-Stock Item
Item #: 32396 -
New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2.
Availability: In-Stock Item
Item #: 32371 -
Reproduction carburetor stud for all Ford numbered Holley carburetors 1967-71. 1/4-20 double ended stud from AMK. Stud only, no wingnut.
Availability: In-Stock Item
Item #: 32579 -
Hex screw for attaching the black plastic elbow to the right or left hand A/C dash duct. Correct replacement #8 washer head tapping screw. Sold individually, two needed per car. One on each side. Fits 1967-68 Mercury Cougar and Ford Mustang with factory air conditioning.
Availability: Out of Stock
Item #: 32996 -
Reproduction vacuum fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All brass fitting, goes into the passenger side of the carburetor for the vacuum advance. This should be ported vacuum.Ford part number 358165-S.
Availability: In-Stock Item
Item #: 33004 -
Reproduction idle mixture screw caps for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All white plastic caps. These were the tamper proof type of caps as installed from the factory.
Availability: In-Stock Item
Item #: 32578 -
5/32 Allen wrench. We offer this Allen wrench to go along with our dash bezel removal tools. This handy dandy 5/32 Allen wrench is needed to attach the ignition bezel tool to any of the 1967-69 Mercury Cougar or Ford Mustang ignition switch bezels.
Availability: In-Stock Item
Item #: 32169 -
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to top loader transmission on all 1967-69 Mercury Cougar and Ford Mustang with 390 or 428CJ engines. AMK number F-1741.