All Available Parts - 1968 Ford Mustang

Nice reproduction of the original alternator wiring harness, 3 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1968 Mercury Cougar standard models or 1967 Ford Mustang with factory tachometer option, all with 390-4V/427/428CJ engines. Ford service number C7ZZ-14305-H, original wire harness marked C8ZB-14305-F or C8ZB-14305-B. This harness is designed for the low mount alternator, or cars with thermactor smog. *Excludes X code 390-2V -...

Used clip found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

New replacement mounting clip as found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Used fixed idler bracket and pulley assembly with new installed bearing for 1968-69 Cougars and Mustangs with the 390 or 428CJ engine. This part will have a small bearing on the pulley and is not marked with a casting number. The 1970 bracket and pulley assembly was a service replacement part and are the same as the 68-69 with the exception of a slightly larger bearing. This later service replacement part is an economically priced service replacement for the earlier originals. All pulleys come...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in...

Used A/C belt tensioning pulley with new bearing. Ford standardized some of the brackets starting in 1968. This adjustable bracket and pulley was used on all 1968-69 390 / 428CJ engines and 1968 289 and 302 engines after 3/1/1968. Additionally it was on 1969 351W engines as well. This adjustable tensioner pulley is identified by having the small bearing pulley. Same as the DOAZ-8678-C adjustable idler pulley only with a big bearing pulley. *Note* All new bearings will have a slight bit of play...

Service replacement A/C belt tensioning pulley with new installed bearing. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc.*Note* All new bearings will have a slight bit of play in them. This is by design, by...

Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.

Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.

Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.   

Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-7/8 inches, sometimes mentioned as 3.15" overall. Applications include 1967-68 Mercury Cougar and Ford Mustang with 289/302 and standard cooling. Reference number YA-79.Ford part # C5OE-8546-A, Ford engineering # C5OZ-8546-A.

Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.

Ford part number C5AZ-6312-B. Application for 1967-68 289 and 302 engines without all of the following; air conditioning, power steering, California thermactor smog. The alternator would also have a single sheave pulley. Ford casting number C5AE-6312-A. Single sheave crank shaft pulley. About 6-5/16 inches in diameter.

C5AZ-6312-D Application for 1967-68 289 or 302 engines with air conditioning. Power steering and or California Thermactor emissions permissible. Ford casting number C5AE-B. Triple sheave 67 68 crank pulley. Inner diameters are about 6-1/2 inches, outer diameter is 7-5/16 inches.

C7AZ-6A312-A. Double or two groove crankshaft pulley. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. 6-1/8 inches in diameter. 1967 Application - Mercury or Ford 289 with automatic transmission and standard cooling (17 inch radiators). Without air conditioning and without power steering. 1968 Application - Mercury or Ford 289 or 302 with or without power steering. Thermactor emissions permissible. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. ...

Ford part number C8OZ-6A312-C. Applications: 1. 1968 289 - 302 engines with Thermactor emissions and manual transmissions, may have power steering or air conditioning. 2. 1969 Boss 302 Eliminators with all applications. Ford casting number C8OE-6312-C. Triple Sheave 68 crank pulley.

Ford part number C8AZ-6A312-C. Application 390-2V and 1968 - 1969 390-4V engines without air conditioning and with power steering. Ford casting number C8AE-6312-C. Double sheave 68 69 crank pulley.

For 1968 390-2V engines without air conditioning, with dual alternator belts, and with power steering. 1968-69 390-4V, 427 GT-E, or 1968-69-70 428 Cobra Jet engines. All without air conditioning. All with dual alternator belts, and with power steering. Triple sheave 1968-69-70 crank pulley.Ford part # C8AZ-6A312-D, Ford casting # C8AE-6312-D.

Ford part number C8AZ-6A312-E. Application 1968 - 1969 - 1970 428 Cobra Jet without air conditioning and without power steering. Ford casting number C8AE-6312-E. Double sheave 68 69 70 428 CJ crank pulley.

Ford part number C8OZ-6A6312-B. Application 289 and 302 engines with air conditioning and power steering optional. Ford casting number C8OE-6312-B. Triple sheave 68 crank pulley. While this pulley is identified as the available pulley over the Ford counter for this application, the C5AE-B pulley is what was installed on 1968 Cougars and Mustangs from the factory.

Application 1968 390-2V with air conditioning and without power steering. Ford casting number C8AE-6312-B. Triple sheave crank pulley, small groove 6 1/8" diameter, large grooves 7 1/4" diameter. Replaces Ford part number C8AE-6312-B.

Application 390 engines with only an alternator and water pump. Ford casting number C8AE-6A312-B. Single sheave 68 crank pulley. 

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

C7AZ-8509-E 289/302 Water Pump Pulley-Used C7AZ-8509-E Thermactor emission systems. Application also includes 1969 Boss 302 Eliminator. All applications are without air conditioning. With or without power steering. Triple sheave pulley all equal diameter at 6-7/16 inches. Ford casting number C7OE-8509-B. *1967 application with standard cooling (17 inch radiator) *After 11-13-1966

For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. 2 sheaves with a diameter of 5-7/8 inches. This is a good copy of the original water pump pulley, it has no stamped part number.Replaces   C6AZ-8509-A or C6AE-8509-A.

C8OZ-8509-A Applications include 1968 289 / 302 with automatic transmissions and 1969 351, all-without power steering, air conditioning and with standard alternator with a single sheave pulley. This pulley is 6-1/2 inches in diameter and is a single sheave pulley. Ford casting number C8AE-8A528-F.

C8OZ-8509-B 1968 289 or 302 with automatic and 1969 351. All without air conditioning but with power steering. Power steering optional if with dual belt alternators. Two sheave pulley, diameter of 6-7/16 inches. Ford casting number C7OE-8509-D. Overall height or depth is 2-7/16 inches.

C8OZ-8509-D Application for 1968 X code 390-2V engines without air conditioning and without power steering. Single sheave pulley, 6-1/8 inches in diameter. *Note* We have found two versions of this pulley and and neither have a casting number stamped in them and Ford lists no casting number, only a part number. To see the earlier and less common version of the two pulleys, click onto the thumbnail.

These 1969 molded vinyl, single post head rests were never offered on a Cougar or Mustang to our knowledge but they make a great "go-around" for the very expensive 1968 dual post headrests. To use them on your 1968 Cougar you will first need a pair of 1969 bucket seats as they have the internal hardware to accept the post. 1968 was a weak design so the 1969 seat frame is a nice upgrade and of course will accept any of the 1968 foam and interior kits. These headrests when in the down position...

Single used post for 1968 dual post head rest. Sold individually, two used per head rest. Ambidextrous, can go on either side, notches to the inside. Comes as shown, chromed rod, nut and lock washer. Fits any 1968 Ford with dual post headrests.  

Comes with all parts shown for one bucket seat, good quality but not as good as original FoMoCo parts. Make sure and check out our good used originals. Replaces Ford part numbers C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A.

Grade A non lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561704-F.

This adjustable linkage kit connects the left track to the right track on a bucket seat. Original Ford part number C5ZZ-6561726-A. Ford description: Rod - Front Seat Track Tie. Listed for bucket seats 1965-1970.

Easy to install, correct tension and length. Includes All the Springs Necessary to Rebuild One Seat. Black Phosphorous Plated. Bucket or Bench seats - 2 kits required for bucket seats. Replaces Ford Parts: (2 - Track assist springs) C5ZZ-6561828-A and (1 - Track latch spring) C0DZ-6461883-A.

This adjustable linkage kit connects the left track to the right track on a bench seat. Original Ford part number C5ZZ-6561726-B. Ford description: Rod - Front Seat Track Tie. Listed for Mercury Cougar and Ford Mustang bench seats 1967-1969.

The bench seat brackets are slightly different than the bucket seat brackets. Our premium grade used tracks are carefully inspected for damage before shipping. Most likely you will have to paint but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. Ford master part numbers...

The knobs for the seat track release to adjust the position of the seat. The reproduction has a slightly deeper divot where you place your finger, and is slightly more round on the bottom, but a very nice reproduction. Replaces Ford Part #: C5AZ-6261753-BA.

This Grade B set will need clean up and servicing but will not have cracks, broken studs or excessive rust. Fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version.

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

Application 1967 - 1968 - 1969 Cougar with either 289 / 302 / 351w engines with air conditioning. After 9-11-66. Casting number 7AD. 5" diameter and a 3/8" sheave width.

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Applications, 1968 289/302 engines without air conditioning, but with dual alternator belts. 390/427/428CJ engines without air conditioning. Casting number 6AA. 4-21/32" diameter and 7/16" sheave width. *NOTE* This is a good alternative for the hard to find AG pulley.

Application, 1968 289/302 engines without air conditioning, but with a single alternator belt. 1969 351w engine without air conditioning, but with dual alternator belts. Casting number 7AE. 4-5/8" diameter and 5/16" sheave width.

Equalizer bar or "Z" bar for small block engines with a manual transmission. Both 3 and 4 speed manual transmissions. Replaces Ford part number C7ZZ-7528-G.

Nice reproduction of the original. Street name is Z-Bar. For all 1967 - 1970 FE engines 390 and 428CJ. Replaces Ford part #: C7ZZ-7528-B.

Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.

Clutch equalizer pivot mount, engine side. Zinc plated. Replaces Ford part #: C7ZZ-7A572-BR.

Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A

Fits the 1967, 1968, 1969 and 1970 Mercury Cougar with the 390, 427, 428CJ or 428SCJ. These have the correct 20 coil spring, but are 1/8" longer than the Ford Master Parts Catalog calls for. Replaces Ford Part #:C7ZZ-7591-AR.

Exact reproduction of the 1967-68 Mercury Cougar and 1966-68 Ford Mustang clutch release fork to equalizer spring. Upper clutch equalizer to firewall, 289 and 302 engines. This unit will also work for 1969-70 Cougar and has the correct spring hook orientation. 66 - 68 Ford specs: 3-1/16" Long 40 Coils 69 - 70 Ford specs: 3-1/8" Long 36 Coils Replaces Ford part #: C3DZ-7523.

(7526) Nylon plastic injected. Correct original design. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these.Replaces Ford Part #: C0AZ-7526-B.Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they...

(7521) The attaches to the bottom leg of your equalizer bar and the pointed end fits into the recess of your clutch fork. Replaces Ford Part #: C7ZZ-7521-L.

This attaches to the bracket mounted on the top side of your pedal hanger over to the clutch pedal itself. Replaces Ford Part #: C2AZ-7534-A.

Injection molded plastic stops underdash squeaking from clutch pedal return spring. 2 required per car. Replaces Ford Part #: C1DZ-7A630-A

Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR

Replaces Ford Part # : C7ZZ-7507-B

(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...

Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.

Reproduction engine side stud for the clutch equalizer bar or z-bar that fits a 289, 302, 351W, or 351C engines in the 67-70 Cougar or Mustang. 

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

Description: The Ford Master Parts Catalog calls this "Bracket - Clutch Release Lever Retracting Spring". This little "L" shaped bracket is found only on 1967 - 1968 Mercury Cougars and Ford Mustangs with a 3 or 4 speed manual transmissions. When people part out early Cougars they often leave this little detail item behind not fully understanding its function or rarity. Stood on end its length at the very longest point is 3 1/4". Its function is to but tension on your equalizer bar when it is...

Z bar return spring for all 1967-68 Mercury Cougar and Ford Mustang. This is the upper spring, proper color and spring tension from original. This is the economy version of the concours spring above. Made in China.

[No Description Provided]

Economy version of the clutch adjusting rod that fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Master clip kit which includes following fasteners: Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorns and regulatorPassenger side apron below relayRadio cable to dashKeep in mind that there are many other fasteners on 1968 Cougars / Mustangs that are not in this kit.

Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Replaces Ford Part # 359747-S

Fits Standard and XR7 Sold as a Set as Pictured.

These reproduction door hinge bolts are for the Mercury Cougar and Ford Mustang and fit both standard and XR7 Cougar. They are sold in a set of 24.Intended for the 1968-70 hinges that are stamped steel, and not cast iron like 1967 hinges.

Sold as a Kit as Pictured.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, most customers will be happy with our reproduction ring that is not brushed. This...

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most customers will be happy with our reproduction ring that is not brushed....

Another great free download for you, our customer! In this free download, John Brower guides you through the installation of an overlay on your dashboard on your Mercury. Simply add this item to your cart and you will receive the download link via email after you complete the order.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. Sold individually.Replaces Ford part # 373556-S.

Sold individually. Zinc (dark silver)

Self threading white plastic. Used on front and rear valances.Sold individually.

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...