All Available Parts - 1968 Ford Mustang

Attractive knob used on later 68 through 69 non XR7 Cougars. I recently installed one of these on my own cars and had the face fall off the main body the first time I used it. I glued it back on and have had no problems since. Replaces Ford Part #: C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard. These 5-1/2 inch wheel will fit over stock disc brake calipers 1968-73. This 5-1/2 inch wheel is...

Reproduction 15x7 chrome styled steel wheel for your Cougar or Mustang. Technically correct for Mustang because of the holes being placed in the center of the arms instead of in the inserts like the Cougar, but will fit both vehicles. Gorgeous reproduction of the original 1968 Mustang styled steel wheel. Correct in every way except that the outer band is welded on instead of riveted to the center section. This wheel has a total width of 7", backspacing is 4" and the center hole is...

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs produced after 1/3/1967. This bracket was utilized throughout the entire 1968 model year and is also listed as the service replacement part for the early mounting bracket.  Ford part # C7AA-2882-L, MPC # C7AZ-2882-G.

Used cast iron lateral compressor support bracket for Cougars and Mustangs built after 1/3/1967 and 1968 cars built prior to 3/1/1968, for both the 289 and 302 engine. Must be used with adjusting bracket C7AZ-8678-B pulley assembly, and pedestal bracket C7AA-2882-L.Ford part # C7AA-2888-G or C7AZ-2888-F.

Used stamped steel lateral compressor support bracket for Cougars and Mustangs built after 3/1/1968 with the 289 or 302 engine. Very close in design to the 1969 351 Windsor, but smaller overall.Ford part # C8AZ-2888-B.

Cast iron pedestal mount for the air conditioning compressor on all 1967 and 1968 cars with 390-2V, 390-4V, or 428CJ FE engines. Mercury and Ford master part number C7ZZ-2882-A, we suspect that this is an error in our 1975 editions of the MPC's. C7SZ-2882-A is what we suspect is the correct number. In any case, C7SA-2882-A is the factory casting number on these brackets.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird, so there are a few minor...

Used steel lateral support brace for Cougars and Mustangs with the 390-2V, 390-4V, or 428CJ FE engines. Identical to the 1970 FE lateral bracket except 1970 versions have square nuts on the reverse.Ford part # C8AZ-2888-A

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing our 1968 selector button kit.Ford part # C8ZZ-19986-A.

Reproduction heater blower switch that mounts to the rear of the factory installed A/C ventilation control panel on  Mercury Cougars and Ford Mustangs.Replaces part # C8ZZ-19986-A.

Reproduction set of A/C register connectors for Mercury Cougars and Ford Mustangs with integral A/C. These mount directly behind the round dash vents and work well with both the original vents or our high quality reproduction vents.

Work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-A.

Passenger side A/C duct register, or elbow, connector for Mercury Cougars and Ford Mustangs equipped with integral or factory A/C. These elbows work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-B.

Vacuum switch not included. This consists of the two lever assembly for the vacuum and cable actuation of the air conditioning plenums damper doors on your 1968 Mercury Cougar or Ford Mustang with integral A/C.Replaces part # C8ZZ-19B888-A for the switch assembly.

These selector buttons are top quality reproductions with a lot of attention given to the details to make these little units look factory fresh and correct.

This reproduction knob set is made by Scott Drake Enterprises. Unlike our knobs, these units have a much larger font. Considering the average Classic Mustang owner is probably 50 years old or more, this was a pretty good idea to do them in this manner since the originals are rather hard to read while driving. If you want user friendly, then this is a very nice upgrade. If you want correctness, then our other set is what you will want. Either way, we got you covered.

Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. This part will not have any missing "chunks" but will show hairline cracks most evident where the heater core tubes pass through. The engineering number imprinted on the back side of this grommet taken from a 1967 Cougar is C7ZA-19B588-A. Good through mid year 1969. Compare to the 1970 item pictured for selection on your late 1969 Cougar.Please indicate in the Order Notes...

Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing, very tough part for us to keep in stock. The metal version is a better part and you can get our metal reproduction unit right here!Ford part # C7ZZ-6501891. ...

Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.

High Quality cloth wrapped heater duct hose. This is the correct length for most cars, but will need to be cut for proper fit in some applications. Hose diameter: 2 1/2"

24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.

Black plastic retainer for attaching the direction air conditioning vent registers.

Reproduction Air Conditioning Vent Air Door Axle for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Round air conditioning vent registers for all 1967-68 Mercury Cougar and Ford Mustang with factory A/C.

25 AMP circuit breaker for all 1968 Mercury Cougars and Ford Mustangs with factory air conditioning. Mounts on the panel, under the dash, next to the fuse block. This particular breaker was also used on the ASC installed 1968 sunroofs. It is 1.07" x 0.40" and has a single green and red dot. Box is marked Tung Sol, 25AMP 12V, and made in the U.S.A. Electrical schematics list this circuit breaker. Ford part # C8ZB-14526-A, C8ZZ-14526-A.

Nice reproduction fresh air vent cable pull assembly. Comes with dash mounted bracket as shown. Much stronger construction than the originals, which were made with a plastic sleeve instead of metal.Replaces Ford part number C7ZZ-6501891-A and C7ZZ-6501891-C.

All new parts for rebuilding the right and left shutoff butterfly in the air conditioning register vents. Fits all 1967-68 Mercury Cougar and Ford Mustang with factory A/C. Kit includes 2 knobs, 2 black butterfly vent doors, 2 shafts, and 2 retainers. All of these individual parts are also separately. Chrome vent registers and vent retainers are also available.

Reproduction factory air conditioning vent register knob. This knob controls the black vent door or valve inside the round registers. These will fit the original axle shafts, but will need to be attached with some super glue or other adhesive. These new knobs fit our reproduction axle shafts that have new splines on them perfectly. Please note the position or orientation of the knob in relation to the position of the internal black plastic butterfly.

Under dash wiring harness assembly for all 1968 Mercury Cougar and Ford Mustangs with integral, or factory installed air conditioning. All wiring harnesses are test and inspected by our electrical department.Replaces Ford part number C8ZB-19945-B.

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade A version will be free of all but very cosmetic defects. Meaning no broken tabs, or torn or missing screens. Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with heaters only used two individual nozzles.

Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade B version may have one of the following: crack or chip, have a broken tab, or a torn or missing screen. B grades will install and work, they just may need a bit of duct tape or be held on with 3 of the 4 screws.Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with...

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, switch, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door. Stapled foam seal to center vent may not be perfect.Replaces Ford part number C7ZA-19740-B.

Repair your own idler / tensioner with our bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8" Overall length 2-3/4" Ford numbers C4AZ-2990-A, C4AA-2A898-A. Check out this video ...

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

New sealed bearing for installing on your 1968-69 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing is physically smaller than the bearing used on the 1968-73 idler pulley (1968-73 bearing sku: 10462). The 1968-73 idler pulley assembly came as a "service replacement" on 1968-69 cars. The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 3/8". On the larger bearing pulley, this measurement is 1 9/16". Both versions of...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Air conditioning bearing replacement service. Send your wide bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new wide bearing. Price includes new bearing (long or short shaft) and labor, shipping extra.  * Note * There are several pulleys that we are unable to press apart. Please check photos for examples of the known pulleys that we can assemble, but not disassemble. *NOTE* Excludes certain 1968 pulleys with stamped...

Repair your own idler / tensioner with our kit which includes a dust cover and is for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  We have had a machinist shorten the shaft on these bearings so that they are easily pressed into the cast pulley brackets that use the short...

Used steel lateral support brace for Cougars and Mustangs with 428CJ FE engines. Identical to the 1968-69 FE lateral bracket except 1970 versions have square nuts on reverse. Also the same bracket for Ford passenger car 390 up until 1971.Ford part # D0AZ-2888-B

NOS long shaft bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8" Ford numbers C4AZ-2990-A, C4AA-2A898-A. Check out this video ...

New 1-1/4 inch expansion plug. Expansion plugs were used as dust covers on the wide bearing style air conditioning pulleys commonly used on Ford cars 1965-68. These are not a real tight fit in those pulleys. Best to still install to keep dust out, we recommend using a bit of JB Weld to hold them.

Used air conditioning vent for any 1968 Mercury Cougar or Ford Mustang with factory installed A/C. These are different than the 1967 A/C vents. For 1968 the vents detached from the main housing for safety reasons. These were meant to 'break away' in the event of an accident. These attach to the housing with a spring, spring sold separately. Grade B decent chrome, there will be some blemishes and minor pitting. A grade versions also available. Fits both passenger and driver side for 1968....

Used retaining spring and two screws for attaching the break away air conditioning vents to any 1968 Mercury Cougar or Ford Mustang with factory installed A/C.

We offer this "Core Grade" assembly for those who purchase the various 1968 reproduction air conditioning bezels. This assembly will provide the needed 'guts' for behind the various 1968 Mercury Cougar or Ford Mustang A/C and heater control bezels. A Complete A/C heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches, and hardware. Ford part # C8WA-19980. *NOTE* Does not include knobs or cable.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Nice fit, made of plastic. Will work with or without console, has slightly wider wings for clearance of the rear of the factory installed consoles.

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs without a console.

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade A vents will not have any cracks or breaks.

Reproduction passenger side A/C vent with black camera case finish for the 67 - 68 Mustang. 

Reproduction black center A/C vent for the 67 - 68 Mustang.

Reproduction driver side A/C vent with black camera case finish for the 68 Mustang.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. We also offer another valve that was used for a period of time see the related evaporator valve.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service. This valve was originally stickered with a FoMoCo tag and...

Two of these little plastic protectors came on Mercury Cougars and Ford Mustangs equipped with Air Conditioning. They are affixed to the front cross member using the same bolts that holds your condenser in place. Their purpose was to protect the wiring harness from potential damage if the car were to get into a collision. These are very hard to find today as most were discarded the first time the condenser was replaced. Even your most experienced judges usually have never seen or heard of this...

This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade A hose that is not cracked, may have a small cosmetic scuff in the foam, and the clips will not be broken. Two required per car, sold individually. We also have a listing for Grade B condition, that will have a minor issue or two. Ford part #: C7WY-19B680 or B5A-18556-C.

Both ends have 90 degree molded ends. Attaches heater core to water heater control valve.Replaces Ford Part #: C7ZZ-18472-CVAC.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade A vents will not have any cracks or breaks.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade B vents will have a small crack or break usually around the mounting holes, but will not effect it's functionality.

Vacuum switch that attaches to the air conditioning lever assembly on all 1967-68 Mercury Cougar and Ford Mustangs with integral A/C.Ford number stamped C7ZA-19B919.

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on...

Grade B used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Some blemishes as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on reverse of this piece is...

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Finally, an answer to the much needed, delicate 1968 A/C side vents! Visually these are very hard to tell apart from the originals we have listed on this site, but functionally, they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. Includes all three control knobs and dealer pricing available.

Concours correct and constructed in original Ford style black thermoplastic material with a nylon barrier. This hose assembly is built to be compliant for R-12 or 134a refrigerants.NOTE: We have three hoses from a previous supplier that we have available for about half the price. The only difference would be that instead of the thermoplastic material, these are the standard rubber type hoses. Pick one up here. ...

This is used on Mercury Cougars and Ford Mustangs equipped with factory A/C. This is the bracket for the valve that stops the flow of warm coolant when A/C is turned on. This is an exact reproduction and has the zinc dichromate finish.

This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.

Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.

These are correct reproductions of the A/C discharge service valve that comes with plastic caps. if you would like the correct aluminum valves, we sell those separately.

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

Regardless of which V-8 engine, C7ZA-19972-E is the correct part number. This hose is approximately 20 inches long. Two different crimped ends, smooth and waffle may be the difference between Dearborn and San Jose or 1967 and 1968. Anyone know?The Ford MPC number is C7AZ-19972-A.

Regardless of which V-8 engine, C8ZA-19835-A or C8ZA-19837-A both can be the correct part number. This hose is approximately 74 inches long. This hose also incorporates the site glass. The Ford MPC # is C8ZA-19835-A or C8ZA-19837-A.

Regardless of which V-8 engine, C8ZA-19867-C is the correct part number. This hose is approximately 55 inches long.Ford MPC part # C8ZA-19867-C.

Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang with factory or integral A/C. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. The 'with air conditioning' hoses have correctly molded 90 degree elbows that fit on the water valve side. Some length trimming may be needed for a tight looking fit.

Concours correct red striped heater hose for late (after 2/1/1968) 1968 Mercury Cougar and Ford Mustang with factory or integral A/C. Durable red striping with "Autolite" spelled out and dated H8A23B. Correct for all V-8 engines with air conditioning. Correctly molded 90 degree elbows that fit on the water valve side. Some length trimming may be needed for a tight looking fit, turn those hoses so that the red striping shows!

Reproduction water inlet elbow for your 1968 big block Cougar or Mustang.Replaces Ford Part #: C8AZ-18599-AClick on images to enlarge. ...

Senses temperature to open and close the expansion chamber and made just like the original.Will work with both R12 and R134 systems.Replaces part #: C7ZZ-19849.

These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B

These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Steel elbow that uses the A/C coupler from the liquid or sight glass hose to the dryer. This is an OEM Ford part that was originally part of an assembly, which included the sight glass hose, coupler, and this elbow. This elbow has the flared fitting common to the 1967-68 A/C connections. We recommend replacing "O" rings prior to installation, which are commercially available from air conditioning service centers.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. This is the uncommon version, we have a limited supply of these from original cars.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C6OZ-19849-A. aka YG-24

This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade B hose that may have a crack or tear, or with a broken clip. Two required per car, sold individually. We also have a listing for Grade A hoses. Ford part #: C7WY-19B680 or B5A-18556-C.

Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.

Fits 1967 Cougar and Mustang with factory Heater Only Firewall and 1967 289 engine. Custom Hurricane Heat Cool & Defrost System for 1967-68 Mercury Cougar / Ford Mustang with original 289 V-8 with or w/o Power Steering. Easy to Install! Hurricane Unit mounts to firewall in place of factory heater, a/c & heater fittings pass neatly through original blower motor hole with custom rubber grommet. Electronic switching package includes correct reproduction A/C Control bezel w/ louvers. Electronic...

Reproduction set of color coded A/C rubber hoses, two T connectors and vacuum diagram.

Used A/C suction service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Used A/C discharge service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Used stamped steel single groove alternator pulley, typically these are described as being 2-7/8 inches in diameter. We find various casting numbers on them, such as: C5AF-10A352-F1, C5AF-10A352-G1, C5AF-10A352-K, C5AF-10A352-L.Replaces Ford part number C5AZ-10344-K.

This is a 'made in China' wiring harness. Quality is OK and will work for this application. Application is 1967-68 Mercury Cougar XR7 models and Ford Mustang without factory tachometer option, all with 289 or 302 engines. *Caution, not for use with Cougar standard models or Mustang with alternator warning light. *Note - Excludes California models or cars with factory Thermactor smog pump with low mounted alternators.Replaces Ford Part # C7ZZ-14305-B Door Tag 65B

1968 Mercury Cougar Standard / Ford Mustang 289 / 302 CONCOURS Alternator Harness with Alternator Warning Light - Repro Nice reproduction of the original alternator wiring harness, 3 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1968 Mercury Cougar standard models or 1968 Ford Mustang with factory tachometer option, all with 289 or any 302 engines. Ford service number C7ZZ-14305-E, original wire harness marked C8WB-14305-D. *Caution, not...