All Available Parts - 1968 Ford Mustang

This is the steel tube that goes from the carburetor to the fuel pump on the 289 or 302 with the AutoLite 4300 4 barrel carberator. Original steel version.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

Reproduction stainless steel line that runs from the fuel pump to the carburetor on your 68 Cougar or Mustang X Code equipped with a 390 2V engine.

This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.

This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The problem with these brass floats, is that after year of being in contact with fuel, they will begin to corrode and disintegrate. We suggest going with the new foam floats. They are fuel resistant and will last longer. Find it here. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Replaces Ford part #C0AZ-9A307-B.

Good used ring with only surface rust and no obvious gouges.

This part is installed on all XR7 fuel sending units and Cougars and Mustangs with the optional Convenience Control Package. Low quality off shore part that requires soldering to your fuel sending unit. This is a temperature sensing device that activates when the fuel level drops enough to expose the unit at which point the circuit is closed and the low fuel light comes on. Commonly referred to as a Thermister / Thermistor / Low Fuel Sending Unit.

New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.

Concourse Correct Hollow Left Rear Stud for the Carburetor Vacuum port to the C6 transmission modulator hose Replaces Part # 382768-S8

1968 289 and 302-2V Autolite 2100 carburetor, automatic C4 transmission - All 50 states. C8ZF-G stamped on the carburetor base, 1.08" venturi size 287 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1968 289 and 302-2V Autolite 2100 carburetor, 3 or 4 speed manual transmission - All 50 states. C8AF-AK stamped on the carburetor base, 1.08" venturi size 287 cfm. Application for 3 and 4 speed manual transmissions. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Trivia time, all C-code 289 Cougars were standard...

1968 302-4V Autolite 4300 carburetor, Automatic C4 transmission- 50 States. C8ZF-D stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1968 390-4V Holley 4150 carburetor, automatic C6 transmission - All 50 states. C8OF-9510-D stamped on the carburetor air horn. Holley list # 3796, 600 cfm.  Core carburetor with proper numbers.  This rebuildable core part may or may not include: the factory Ford Autolite tag that was affixed to the toptransfer tube good choke assembly

Our service is to rebuild your sending unit. A quality core is required. This rebuilt XR7 fuel sending unit has been meticulously gone through and made operational again. All sending units are taken apart and media blasted. Once cleaned, the thermistor is carefully removed from the tube and opened up so that the mesh screen and insulator can be chemically cleaned. All wire leads are removed and tested, then resoldered to their contact points. Upon reassembly, initial testing is done with VOM....

This is the single prong version fuel sending unit for 67 - 68 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. *Note - This reproduction sending unit is technically a copy of the 1968 version. Be aware that the...

This is the stainless steel, single prong version fuel sending unit for 67 - 68 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. *Note - This...

Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1967 - 1968 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1968 fuel sending unit with three prongs (2 electrical and 1 alignment prong). The original Ford casting number was C8ZF-9275-B, master parts catalog number C8ZZ-9275-D. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely...

This plastic protector sleeve is often missing or broken, but occasionally we come across a good used one. This part attaches just in front of / below the fuel tank on the passenger side, and serves two purposes: it routes the wiring closer to the fuel sending unit without it dangling down, and protects it from road debris This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

This is a single plug (standard models without low fuel warning light) fuel sending unit with an extra bung for a return line for 1967-68 Cougars and Mustangs running fuel injection. No need to change the whole tank in order to upgrade your car to fuel injection!  Main line 3/8" Return line 1/4" Check out the video below on our new gauge tester: ...

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

This option requires that you pay a $65 core charge.  Be aware that the OEM Ford 1968 sending units had 3/8 inch tubes for the filter, 1967 had 5/16 inch tubes. Our service is to rebuild your standard fuel sending unit. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality core must be complete and not overly corroded. We are unable to...

Reproduction heater dash plate for the 68 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).

Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

New improved set of 6 screw for the glove compartment hinge on all 1967-68 Mercury Cougar and Ford Mustangs. Three 10-24 bolts with 0.72" conical washer heads to go into dash, and three 10-24 bolts with 0.50" conical washer heads to attach to glove box door. This is an updated proper kit for 1967-68 Mercury Cougar and Ford Mustang glove box door hinge. All AMK bolts, but WCCC special recipe. 6 pieces as shown.

Used glove box liner or plastic box for any 1968 Mercury Cougar or Ford Mustang these do have the flat smooth area for installing the tire pressure decal. This is nearly the same as the 1967 used and Scott Drake reproduction, which lack the smooth section for the tire pressure decal. Good used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange.Replaces Ford part number C8ZB-6506010-A.

Used hinge for any 1967-68 Mercury Cougar or Ford Mustang. This hinge has two ribs formed for added strength. There was an early 1967 version of this hinge that did not have the ribbing. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint. Replaces Ford part number C7ZZ-6506050-B.

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Used glove box catch for any 1967-68 Mercury Cougar or Ford Mustang. Several versions of this catch were used 1967-68, this is the most common version. Replaces Ford part number C6OZ-6206064-A.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. See related for reproduction and 1967 used.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1967, notice the push button with square edge? 1968 push buttons had rounded edges. See related for reproduction and 1968 used.

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Reproduction medium blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed.*NOTE* There are two types of this trim found in the 1967-68, the smooth or rough texture. ...

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used ignition lock cylinder bezel for any 1967-68 Mercury Cougar, ford Mustang and likely Fairlane / Comet. Good used condition, we recycle the pitted crusty ones. Half the price of the repop version. We also sell the special tool that removes this without hassle or damage.Replaces Ford part number C6OZ-11584-A.

Reproduction headlight knob, retainer & bezel, cigar lighter and ignition switch retainer.

Headlight switch knob for any 1968 Mercury Cougar or Ford Mustang. Not the same as 1967, which is reproduced by Scott Drake. This is a nice detail item for concours judged cars. There is a difference between 1967 and 1968 knobs as shown in the photos. Nice used condition. Original Ford part number C8ZZ-11661-A.

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

Fits either 1967 or 1968 Mercury Cougar or Ford Mustang. Technically this is a copy of the 1967 factory installed version. 1968 factory glove box liners have a smooth section for installing the tire pressure decal. See the related items for 1967 and 1968 good used liners. Replaces Ford part #: C7ZZ-6506010-A.

Used glove box liner or plastic box for any 1967 Mercury Cougar or Ford Mustang. This is the same as the Scott Drake reproduction, but it lacks the smooth section for the tire pressure decal which was introduced on the 1968 cars. Used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange, Replaces Ford part number C7ZB-6506010-A.

A great optional accessory. All new tooling was created to produce these glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Replace Ford Part #: C6DZ-6506072.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # C8ZZ-6524100-BK.

Unlike the light blue found on a Cougar this is the darker blue used on the 1968 Mustang. The light blue is not available. This is a good match to the darker blue accents found on the 1968 standard and decor Cougar interior. Color on these is inconsistent and never spot on to the original. No returns on this item.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101 Color on these is inconsistent...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101. ...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests...

Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being blunt about the quality on some of these items, but after using these...

Unlike the light blue found on a Cougar this is the darker blue used on the 1968 Mustang. The light blue is not available. This is a good match to the darker blue accents found on the 1968 standard and decor Cougar interior. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue, Parchment, Ivy Gold, Aqua, Saddle, or Nugget Gold. Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests are not correctly colored...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. Color on these is inconsistent...

Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being blunt about the quality on some of these items, but after using these...

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

Decent used horn ring but unlike our grade "A" used horn ring this one will have very minor pitting but no open blisters in finish. Good value for your driver quality 68-69 Ford / Mercury with two spoke steering wheel.

Better quality than our reproduction for less money. Ford part number C0DZ-13807-A.

Used on two spoke steering wheels. Replaces Ford Part # C0DZ-13807-A. Although it does not "look" right it will function correctly. Those in the know will purchase our good used spring.

Horn ring contact components for the standard horn ring found on 68-69 2 spoke steering wheels. Ford part number C9AZ-13A805-B. Not as shiny as the reproduction kit but the price is less and the quality is FoMoCo original all the way. Reference photo above is the order in which the parts are installed.

Exact reproduction horn ring contact components for the standard horn ring used on two spoke steering wheels, replaces Ford part # C9AZ-13A805-B. Includes new hardware

Perfect fit.

Pictured in black. This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Check out this video ...

New screw for attaching horn pads onto steering wheels 1968-69. 2 or 3 required, sold individually.

Good used standard steering wheel from a 1968 base model Standard Cougar, or Mustang or nearly any Ford. This is not the deluxe steering wheel with simulated wood grain. Solid color only. Plan on respraying the color for a fresh look. We normally have black in stock, other colors sometimes available. Usually these will have minor cracks at 12 and 6 O'clock. There is also a very good reproduction available, please see related items. Check out this video ...

B grade pad has shrunk to the point that the center section will not fit well and you may have to file some of the plastic away for a proper fit, it will be curling a little at the top where it meets the wheel and overall will be rather hard from UV exposure. Additionally, it may show some signs of wear to the texture of the graining. If you state your preference in the comments section we will try to accommodate you on color.

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

Reproduction Two Spoke Steering Wheel Pad for the 1968 Mercury Cougar Check out our video review

Pit free original rear console courtesy light for all consoles 67-68, does not usually come with a good lens as most are cracked, faded or missing. Casting number as seen on the back reads C7ZB-13743-A. Number imprinted on wire can be: C4VB-13757-A.

Map light bezel for overhead roof consoles on both 1967-68 Mercury Cougar XR7 and Ford Mustang. These are a great reproduction at a great price. These were always pitted and before the reproductions came out three years ago a very nice used pair sold for about $100. To date we have sold more than 300 pairs and have had great feedback! Sold in pairs. Bezels only. Sometimes called a 'door' Ford part number C7ZZ-13788-A. *Customer Comments* Hello. I just bought my first 1967 Cougar XR7 in about...

Good used shift indicator light and pigtail for the 1968 with automatic and without console. Comes as shown with the clip on diffuser for automatic shifter lever. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...) The 1968 wiring harness has a blue double male plug. Fits 68 CougarFits 68 Mustang Check out our...

The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages. Check out this video below where we used Kevin Marti's books extensively to decode a 1969 428 CJ Cougar

This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...

These pamphlets were found buried in the back room of a San Jose California Lincoln-Mercury dealership. There was no reason to keep them after the warranty expired so most were discarded long ago. Great for that person who likes original documents. Limited quantity.

Manual on how to modify your FE big block Ford for street or strip.

Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.

Reproduction BOSS 302 Chassis Modification for the Strip Track Manual. This little book is packed full of tips and tricks to make your Cat or Pony and handling MACHINE! The tips in the manual also apply to the 1967-68 Cougar or Mustang. Time to sharpen the claws on your flexxy feline!

Great option for international customers. Light weight, and all you need is a PC or laptop, and you can plug this drive in and access all the same information that you'd find in the full sized shop manual books.

Complete reprint of the 1968 Vacuum Schematic for the Mustang.  You can find the free download for the headlight vacuum system here.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

This USB flash drive contains the complete Autolite 4300 carb information from overhauling, to diagnosis and repair. A must for anyone planning to work on their own carburetor. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of this manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with USB support), and you can plug this drive in and access all the...

These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand.Here is a helpful youtube video on how to go about removing a headlight...

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Quality reproduction to replace your pitted original. Replaces Ford Part #: C7ZZ-10852-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Inexpensive upgrade, replaces that bezel damaged by improper screw driver removal. We also sell the special tool that removes this without hassle or damage

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair.Replaces Ford Part # C8ZZ-6526656. *Customer Feedback* Don and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy...

These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair Replaces Ford part # C8ZZ-6526656.

The same plastic lock rod grommet but with a nice chrome finish for an extra touch. Sold in pairs. Replaces Ford Part #: C5DZ-6221999-B or C5DZ-6221999-C.

Good Reproduction of the clear plastic door lock grommets. Sold as a pair. Replaces Ford Part #: C5DZ-6221999-B.

Plastic injection molded, chrome plated like the originals. The detail on the top is not exact to original. Sold as a pair.Replaces Ford part number C8AZ-6221850-A

Polished stainless steel with correct internal black felt anti-rattle pad. Sold as a pair.