All Available Parts - 1967 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 201-300 of 3156
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 19083 -
Full set of metal radio knobs for the 1967 Mustang or Cougar. Not for use with the 1967 Cougars equipped with factory center console. Keep in mind we have reproduction knobs that will work in place of these.
Availability: Used / Wrecking Yard Item
Item #: 24036 -
This is one of the easier knobs to find in that it does not break easily and can be found on many 1967 FoMoCo products. Not used on Cougars with a center console and little to no differences can be seen between the different examples. One explanation for having multiple casting numbers for the same part is that Ford would use multiple suppliers for a single part. To differentiate which part came from which vendor, different casting numbers would be assigned. If there was a problem with a run...
Availability: Used / Wrecking Yard Item
Item #: 24038 -
Used on early non console 1967 models and has a lower profile than the later version. We also have pitted knobs we can throw in on a order for free, just mention it if all you need is a knob that gets the job done.Ford part # C7MA-18817-A.
Availability: Used / Wrecking Yard Item
Item #: 24206 -
Unlike the plastic console knobs, the issue with these metal knobs is pitting as opposed to breaking. Very hard to find in clean condition.Replaces part # C7ZA-18817
Availability: In-Stock Item
Item #: 10441 -
Reproduction positive crankcase ventilation valve or PCV valve for 1967 Mercury Cougar, Cyclone, Ford Mustang and Torino all with 390GT or S code 390-4V engines. This valve has a stamped casting number of C7AE-6A666-B, comes with a white plastic ring as shown. Ford engineering number C7OZ-6A666-A. Also used on 1967 Shelby Mustang GT500, Ford 428PI, and Mercury Cougar GT-E 427-4V engines. *Note - Must be used with either a reproduction or original 90 degree PCV adapter. ...
Availability: Used / Wrecking Yard Item
Item #: 30252 -
Hot idle compensator valve assembly for many Ford engines with PCV, starting in 1964 through early 1968. Typically found on 1964-66 Ford 260-2V, and 289-2 engines with air conditioning. 1967-68 289-2V, 302-2V and some 390 engines all with air conditioning and PCV or closed emissions. The Ford assembly manual indicates that the Hot Idle Compensator Valve 'T' Assembly, was installed by removing 3/4 inches of the PCV hose, 2-1/4 inches (on center of the PCV valve). See picture for clarification....
Availability: In-Stock Item
Item #: 31588 -
Reproduction hose that connects the oil cap to the air cleaner on cars equipped with the 289 engine. Replaces Ford Part number C6AZ-6A664-P
Availability: Used / Wrecking Yard Item
Item #: 31988 -
Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 2 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Replaces Ford part number C6AZ-9A474-A.
Availability: Used / Wrecking Yard Item
Item #: 32095 -
Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.
Availability: Used / Wrecking Yard Item
Item #: 32105 -
Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 3 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Bob Mannel's book indicates that this vacuum fitting was for A/C and Thermactor smog. Replaces generic Ford vacuum fitting part number 9A474.
Availability: In-Stock Item
Item #: 10598 -
This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...
Featured!
Availability: In-Stock Item
Item #: 26015 -
Note: Not for use with aftermarket radios. Finding correct radio knobs for a 1968 Ford Mustang or Mercury Cougar equipped with a center console has been a huge obstacle for decades now. To clear the padded radio bezel cover, one must have these elusive, one year only, deep well knobs. These will also work on 1967 Cougar with console and although they would not be letter correct for anything but a 68 with a console, they do not look out of place on a 67 with console. Note that this four piece...
Availability: In-Stock Item
Item #: 11063 -
Nice reproduction 1967 Cougar and Mustang radio knobs for use with factory radios. For use without the console option, these have the later style and knob height. This reproduction knob set does not have any Ford casting numbers and are chromed metal knobs, not plastic. The inner knob on the 1967 AM radio station adjusting dial will need a white sleeve our part number 10022230. Factory radios with fader control will not need the sleeve.If you want to use these knobs on your 68, they will work...
Availability: Out of Stock
Item #: 26213 -
This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...
Availability: Used / Wrecking Yard Item
Item #: 15-0010 -
1967 Cougar Owners:
To view our exploded view interactive diagram of the tilt steering column parts, click here. This is my absolute favorite Cougar - Mustang - Shelby option of all time! In fact, as a rather tall person that is not as slim as I once was, I do not really enjoy driving a Mustang or Cougar that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side...
Availability: Used / Wrecking Yard Item
Item #: 15-0024 -
Knob for engaging the emergency flasher switch on a fixed (non-tilt) steering column. This original knob is plastic, the reproductions are chrome plated die cast.
Availability: In-Stock Item
Item #: 26181 -
For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518
Availability: Used / Wrecking Yard Item
Item #: 15-0021 -
Good used part without excessive rust or damaged rubber. For use with fixed column only.
Availability: Out of Stock
Item #: 15-0083 -
Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...
Availability: In-Stock Item
Item #: 10121 -
Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting.
Availability: In-Stock Item
Item #: 11822 -
12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.
Availability: Used / Wrecking Yard Item
Item #: 15-0352 -
Bare outer tube for the 1967 Cougar or Mustang tilt steering column. This item will be free of major rusting and will have to be painted to match your car. Keep in mind that these tubes are specific to each year. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out our video on Tilt Column service and repair below. ...
Availability: In-Stock Item
Item #: 10665 -
We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation.
The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...
Availability: Used / Wrecking Yard Item
Item #: 15-0146 -
Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: Used / Wrecking Yard Item
Item #: 15-0145 -
Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: In-Stock Item
Item #: 15-0178 -
Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: In-Stock Item
Item #: 15-0179 -
Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: In-Stock Item
Item #: 31804 -
This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 32067 -
Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft. The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...
Availability: In-Stock Item
Item #: 32897 -
Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Ford part # D1AZ-3518 or E2AZ-3518
Availability: In-Stock Item
Item #: 30246 -
This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...
Availability: In-Stock Item
Item #: 15-0193 -
Used steering column release rod which is attached to the vacuum motor and lock pin, and also pushes the neutral safety switch.
Availability: In-Stock Item
Item #: 31243 -
New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S
Availability: In-Stock Item
Item #: 33159 -
Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal.
Availability: In-Stock Item
Item #: 33162 -
Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions.
Availability: In-Stock Item
Item #: 33188 -
Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.
Availability: In-Stock Item
Item #: 33189 -
Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.
Availability: In-Stock Item
Item #: 33182 -
Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford.
Availability: In-Stock Item
Item #: 33179 -
Replacement cork pan gasket for all 1965-73 C4 Ford transmissions.
Availability: In-Stock Item
Item #: 33178 -
Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.
Availability: In-Stock Item
Item #: 33177 -
Rubber pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Cork gasket also available.
Availability: Out of Stock
Item #: 33172 -
Basic C6 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C6 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that U code C-6 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.
Availability: In-Stock Item
Item #: 33167 -
Basic C4 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C4 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.
Availability: Out of Stock
Item #: 33173 -
Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops.
Availability: Used / Wrecking Yard Item
Item #: 12829 -
Used grade A trim ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 1968 SS wheel. No dings or scratches that cannot be buffed out. sold individually.Replaces Ford part number C6ZZ-1210-A.
Availability: Download
Item #: 90021 -
Another great free download for you, our customer! In this free download, John Brower guides you through the installation of an overlay on your dashboard on your Mercury. Simply add this item to your cart and you will receive the download link via email after you complete the order.
Availability: In-Stock Item
Item #: 19951 -
These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually.
We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...
Availability: Out of Stock
Item #: 26123 -
This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...
Availability: In-Stock Item
Item #: 41280 -
Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...
Availability: In-Stock Item
Item #: 41336 -
This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Availability: In-Stock Item
Item #: 41253 -
Sold individually.
Zinc (dark silver)
Availability: In-Stock Item
Item #: 14321 -
Self threading white plastic. Used on front and rear valances.Sold individually.
Availability: In-Stock Item
Item #: 41144 -
Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...
Availability: In-Stock Item
Item #: 10616 -
Description:
The Ford Master Parts Catalog calls this "Bracket - Clutch Release Lever Retracting Spring". This little "L" shaped bracket is found only on 1967 - 1968 Mercury Cougars and Ford Mustangs with a 3 or 4 speed manual transmissions. When people part out early Cougars they often leave this little detail item behind not fully understanding its function or rarity. Stood on end its length at the very longest point is 3 1/4". Its function is to but tension on your equalizer bar when it is...
Availability: In-Stock Item
Item #: 42396 -
Z bar return spring for all 1967-68 Mercury Cougar and Ford Mustang. This is the upper spring, proper color and spring tension from original. This is the economy version of the concours spring above. Made in China.
Availability: Used / Wrecking Yard Item
Item #: 19165 -
This adjustable linkage kit connects the left track to the right track on a bench seat. Original Ford part number C5ZZ-6561726-B. Ford description: Rod - Front Seat Track Tie. Listed for Mercury Cougar and Ford Mustang bench seats 1967-1969.
Availability: Out of Stock
Item #: 19166 -
The bench seat brackets are slightly different than the bucket seat brackets. Our premium grade used tracks are carefully inspected for damage before shipping. Most likely you will have to paint but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. Ford master part numbers...
Availability: Used / Wrecking Yard Item
Item #: 31972 -
Original used oil filler cap adapter for any 1967 Mercury Cougar or 1965-67 Ford Mustang. This is for use with the open emissions, push on oil cap. This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D. Will most definitely need a new gasket. These will ship "as found" or fresh from our wrecking yard. Photo is most cases will show a cleaned part for glamour photography shots. Also have reproduction version.Ford part...
Availability: In-Stock Item
Item #: 14229 -
OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.
Availability: In-Stock Item
Item #: 18646 -
Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675
Availability: In-Stock Item
Item #: 17771 -
Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302
Availability: In-Stock Item
Item #: 14234 -
OEM Style Oil Pan Gasket.
Availability: Ships Direct from Supplier (Except International)
Item #: 15311 -
This is by far the best, most correct FE pan ever offered. Very accurate reproduction of the C6OZ-6675-A oil pan used first on the 1966 Fairlane and Comet with one of the 390 CI optional engines. It is 100% correct for 1968 and early 1969 428CJ. It is not 100% correct for the 428SCJ but still a good alternative.
Availability: In-Stock Item
Item #: 41450 -
Quality After-Market oil filter for the 1967 - 1973 V-8 Mercury Cougar or Ford Mustang. Better filter than OEM.
Availability: In-Stock Item
Item #: 17772 -
Reproduction Small Block Chrome Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302
Availability: Out of Stock
Item #: 11359 -
Availability: In-Stock Item
Item #: 15379 -
Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.
Availability: In-Stock Item
Item #: 11006 -
New oil pan drain plug with zinc coating and plastic gasket. Fits all Mercury Cougar and Ford Mustang V8 oil pans 1967-73.
Availability: In-Stock Item
Item #: 11007 -
Replacement oil pan plug that is magnetized for collecting ferrous metal in the oil system. Replaces Ford part number C5ZZ-6730-M and D1AZ-6730-A. Fits all Ford engines 1967-73, including 6 cylinder, 289, 302, 351w, 351c, 352, 390, 427, 428, 429, 460.
Availability: In-Stock Item
Item #: 11003 -
Reproduction oil pan bolt kit for the Mercury Cougar or Ford Mustang equipped with the 289, 302, or 351W engine.
Availability: In-Stock Item
Item #: 13120 -
New oil pan drain plug, Ford engine blue painted, with plastic gasket. Looks correct, but has a different sized head than factory oil pan bolts. Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200,...
Availability: In-Stock Item
Item #: 13121 -
New Chrome oil pan drain plug, with plastic gasket. Has a different sized head than factory oil pan bolts.Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200, 240, 250, 289, 302, 351, 352, 410, 427, 428, and 429 engines 1965-1973. ...
Availability: In-Stock Item
Item #: 31055 -
Oil pan bolt kit for all FE 390, 427, and 428 engines. Set is made by AMK and includes 20 OEM style bolts and washers. We sell them specifically for 1967-70 Mercury Cougar and Ford Mustang, but they will fit most all Ford "FE" engines including 352, 410, and 360 Ford engines. If you happen to have a 428CJ with windage tray, we also offer a set of bolts for that application too. ...
Availability: In-Stock Item
Item #: 31056 -
Oil pan bolt kit for all 428 Cobra Jet and 428 Super Cobra Jet engines with windage tray. Set is made by AMK and includes 20 OEM style bolts and washers.
Availability: Used / Wrecking Yard Item
Item #: 33549 -
Used oil screen pick up tube assembly from a small block Ford 260, 289, or 302 engine. This is for most front sump 260, 289, or 302 engines in Ford cars up to at least 1972. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item.* Excludes 351W and 351C engines, and all F Series...
Availability: In-Stock Item
Item #: 14210 -
Original design in chrome. Beautiful fit, a really nice part. Replaces Ford part # C6AZ-6754-C.
Availability: In-Stock Item
Item #: 15295 -
Original design in painted Ford Blue. Beautiful fit, a really nice part. Also known as oil level indicator tube. Replaces Ford part # C6AZ-6754-A.
Availability: In-Stock Item
Item #: 15294 -
Nice chrome finish. Also available in Ford blue. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375 With the paint Stripped, it measures .365 It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A. ...
Availability: In-Stock Item
Item #: 41535 -
Also available in Chrome. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375With the paint Stripped, it measures .365It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A.
Availability: In-Stock Item
Item #: 11271 -
Nice reproduction oil dipstick made from all stainless steel. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals.Replaces Ford part # C7OE-6750-B or C8OE-6750-B.
Availability: Used / Wrecking Yard Item
Item #: 27352 -
Engine oil dipstick as found on most any 1967 Ford with 289 engines (C, A, or K Code). This has the correct small shield as found on 1967 and earlier cars, starting in 1968 this dip stick gained a larger 'bell' shaped shield that went over the dip stick tube. Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dip stick end is approximately 19.40 inches. The handles appear to have been painted black...
Availability: Used / Wrecking Yard Item
Item #: 27357 -
Chromed engine oil dipstick as found on many 1967-69 Ford with 390 engines (S Code), 427-4V (W Code), 428CJ (Q or R Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end varys at either 19.25" and approximately 20.25" (full, add, and safe marks are the same). The handles were chromed originally. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.
Availability: Used / Wrecking Yard Item
Item #: 27358 -
Painted engine oil dipstick as found on many 1967-69 Ford with 390 engines (S or X Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. From the top of the shield to the dipstick end varys from either 19.25" to approximately 20.25" (full, add, and safe marks are the same). The handles were painted blue originally. Typically the painted dipsticks were found on the non-GT (6.5 Litre) cars in 1968. Ford part # C7AZ-6750-A, Ford casting...
Availability: In-Stock Item
Item #: 41566 -
This 49 state oil filler cap fits valve covers that utilize twist-on oil caps. This cap is a reproduction of the original cap that was found on 1967 models with the S code 390 and 289 engines with dress up kit like found on DGS 1967 Cougars.. This part features a quality chrome finish along with a crisp "FoMoCo" stamping. At its widest point it is 3" in diameter. The total height is 2 1/4" high including the portion that goes into the valve cover.* Trivia - For 289 engines it should have an...
Availability: In-Stock Item
Item #: 13859 -
Correct detail. Chrome plated with oval-style FoMoCo script stamped into the top surface of cap. This is a push on cap and requires the type of cap that has a round filler tube protruding from the driver side valve cover. This is the correct Open Emissions oil cap for the finned "G" valve covers we sell.
Availability: In-Stock Item
Item #: 13861 -
Correct detail. Chrome plated with rectangle-style FoMoCo script stamped into the top surface of cap. Nipple measures 5/8" diameter. This is the correct Closed Emissions oil cap for the finned "G" valve covers we sell.
Availability: In-Stock Item
Item #: 13862 -
Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.
Availability: In-Stock Item
Item #: 13860 -
Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.
Availability: In-Stock Item
Item #: 15831 -
Reproduction black oil cap for your 67 - 70 Cougar or Mustang, featuring the FoMoCo logo.
Availability: Used / Wrecking Yard Item
Item #: 17293 -
Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 engine. This black painted twist on oil cap was found on non-emission cars. Meaning 49 States except for California.*Note - a chromed version was also available with engine dress up kits.
Availability: Restored / Remanufactured
Item #: 30847 -
Rechromed, used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 or 390 and California emissions. This chromed push on oil cap was used on the DGS package or 390 GT engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California.
Availability: Used / Wrecking Yard Item
Item #: 23915 -
Smooth painted valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 Mercury Cougar and 1966-67 Ford Mustang with 289 engines. These will be dirty, and scratched. Plan on cleaning thoroughly, doing minor body work, sanding and painting prior to installation. Ford part # C6AZ-6582-G. *Restoration Tip* "Powered by Ford" valve covers were not generally used until the 1968 model year. These smooth small block valve covers are correct for 1967 cars. Those wanting to...
Availability: Used / Wrecking Yard Item
Item #: 24017 -
C7AZ-6582-A Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1967-1969 Mercury Cougar with 390 engines. We are pretty sure that these painted valve covers were installed on non-GT cars without the engine dress up kits. Most 6.5 liter cars and the X code 390-2V would have had these painted valve covers. Right is the same as left, these are sold individually. Getting hard to keep in inventory, plan on some minor rust and or straightening. A good junk...
Availability: Used / Wrecking Yard Item
Item #: 24069 -
C7OZ-6582-C Chromed valve cover with "Powered by Ford" embossed in the metal. Correct on 1967-1970 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. These are used, and will have some minor pitting or stains in the plating.Sold individually *Restoration Tip - The difference between the chromed 390GT valve cover and painted valve covers is only the chrome plating. *Note - Some 1969-70 428 Cobra Jet engines came with one of two different styles of finned cast aluminum valve covers. ...
Availability: In-Stock Item
Item #: 13974 -
This is the nylon roller that fits on the end of the window regulator arms. Includes rivet. Sold individually. 2 rollers required per window, 4 rollers required per car. Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" Diameter Here's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: ...
Availability: In-Stock Item
Item #: 41183 -
Fits 1967 and 1968 Standard or XR7. Holds "J" shaped plastic hinge covers in place.
Availability: In-Stock Item
Item #: 26077 -
1969-70 actually used a star head bolt but these are a much more user friendly screw that will work in its place. Sold in a set of four which is what you will need for one seat.
Availability: In-Stock Item
Item #: 41177 -
Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.
Availability: Rare / NOS Part
Item #: 26804 -
Ford Part # 379390-s
Sold individually
Availability: In-Stock Item
Item #: 26066 -
Includes a pair of chrome screw adjusters, nuts and washers, heavy duty plastic rest plates and attaching screws to repair or replace that missing seat back adjustment.Replaces Ford Part #: C1DZ-6461643