All Available Parts - 1967 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 2601-2700 of 3156
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 11-0220 -
Good used, original FORD regulator that has been closely inspected for wear on the gears and cracks in the rollers.Replaces Ford Parts #: C7ZZ-6523200-AUnlike the new units our used units come with a three year warranty!1967 & 1968 Stamped Markings: C7ZB-6523232-A, C7ZB-65234A12-A & C7OB-65223220-A.*NOTE* - Rarely do we find a flawless driver side regulator for 1967 - 1968.
Availability: Out of Stock, On Order
Item #: 13713 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: Out of Stock
Item #: 11-0165 -
375694-S2 Special set screw for the rear door guide. This one is shorter than the two that install in the vent window frame and front door glass channel. This set screw has a 5/32" hex head with 5/16" NC threads, and is 1-9/16 inches in overall length. This set screw also has a ¾ inch diameter shoulder. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure. See...
Availability: Out of Stock, On Order
Item #: 15621 -
Used under dash wiring harness repair plug and pigtail for the neutral safety switch / back-up lights and engine feed harness for the LATE 1967 Mercury Cougar. Works for both standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The blue/red to yellow/black wire is for the radio feed. The only difference between the early and late harnesses, is the early harness has an extra blue wire.
Availability: Out of Stock
Item #: 11-0186 -
C7ZZ-65222A56-KIT Guide with hardware for the passenger side door glass of all 1967-68 Mercury Cougar and Ford Mustangs. Sometimes called the slider, mounts to the door. Kit includes guide, attaching bolts, detachable stop, and special set screw and nut for angle adjustment. *Installation hint - all of the dried crusty 40+ year old grease should be removed and fresh white grease should lavishly be coated in the channel.
Check out our handy diagram below to find other '67-'68 door parts you may...
Availability: Out of Stock
Item #: 24272 -
C7ZZ-5482-B This is a factory used front sway bar. This is the same size 3/4 inch diameter as the 289 and 302 sway bar but has a slight difference in the bends for the 1967 390-4V or 6.5Liter engines. This bar was factory identified with a One-Yellow and One-Blue paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.
Availability: Out of Stock, On Order
Item #: 31550 -
Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.
Availability: Out of Stock, On Order
Item #: 11794 -
This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.
Availability: Out of Stock
Item #: 31253 -
Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73. A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...
Availability: Out of Stock
Item #: 23809 -
C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.
Availability: Out of Stock
Item #: 16-0047 -
Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.
Availability: Out of Stock
Item #: 30532 -
Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.
Availability: Out of Stock
Item #: 30653 -
Also called a pumpkin, 3.00:1 locking ratio.Check your door tag under "Axle".Please note, that this is a vintage, two pin equa lock third member. Most of us should be looking at a modern design traction lock for spirited driving. The 1960's Equa-Lock, is pretty weak.1967 code A 1968 code E
Availability: Out of Stock
Item #: 27513 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1967 late 9 inch rear end housings without fill plug in the steel...
Availability: Out of Stock, Discontinued
Item #: 19799 -
Limited slip nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch cases from 1967-1973 with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit came in Cougars and...
Availability: Out of Stock
Item #: 26525 -
Mounts on floor pan above the center of the rear axle over 3rd member on small block cars with 8 inch rear ends. Mustang only, will not fit a Cougar.Replaces Ford part #: C5ZZ-4730-B orC3AZ-4730-B. Customer Comment:Thank You Don and WCCC,Copy Cat's almost done!Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product.Without their patience and understanding along with a great selection of parts I wouldn't have her in such great shape.Thanks guys, along...
Availability: Out of Stock
Item #: 24268 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Rear axle assembly - Housing, Axles, brake backing plates, and third member. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. 1967 early 9 inch rear end housings had the carry over fill plug in the steel housing as seen from the back of the car. As removed from West Coast Cougar organ donor car. We recommend a bearing...
Availability: Out of Stock, On Order
Item #: 12979 -
This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.
Availability: Used / Wrecking Yard Item
Item #: 30220 -
Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and C-6 (automatic code U) transmission. This supplier with the Ford number stamped on the side strap is typically from Dearborn assembled cars. Used core radiator for recoring and restoration. This listing currently has an older replacement 4 tube core. The lower tank has minor damage to the area of the pet cock as shown. Typical Dearborn installed assembly line radiator.Replaces...
Availability: Out of Stock
Item #: 30221 -
Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and manual transmission. Used core radiator for recoring and restoration. This listing currently has a lower tank with minor damage to the area of the hose outlet as shown. Typical Dearborn installed assembly line radiator.Replaces Ford part number C7ZE-8005
Availability: Out of Stock
Item #: 30226 -
Used FoMoCo 20 inch small block radiator. This is for a 1967 Mercury Cougar or Ford Mustang with 289-2V, or 289-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 7EC or 3rd week of May 1967. Late production date. Ford part number C7ZE-8005-S1 ...
Availability: Out of Stock, On Order
Item #: 14179 -
These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.
Availability: Out of Stock
Item #: 23940 -
C6OE-F Clutch style cooling fan found on all 1967 S code 390 engines, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C6OZ-8600-F. Original fan drive clutch cast number for this application is C7ZE-A. If you have one of these fans and would like to trade it straight across for one of our C8OE-B or C9ZE-E fans please contact us! Check out this interesting video where they test the...
Availability: Out of Stock, On Order
Item #: 12457 -
Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.
Availability: In-Stock Item
Item #: 31578 -
Used original fan shroud for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. Shround will have minor damage as shown. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. Ford part # C9OZ-8146-A For some helpful tips on upgrading your Cougar (or Mustang) cooling...
Availability: Out of Stock
Item #: 23840 -
C5AE-B This is the early 1967 production cooling fan, used up until 11/14/1966 on 289 engine applications. This does not include those cars with factory, or "integral" air conditioning. Fan description - 5 blades and 17 inches in diameter. Ford master part number C5AZ-8600-A. *Note - Excludes integral air conditioning. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...
Availability: Out of Stock
Item #: 23939 -
C6OE-D and C7AE-F marked fans. Applications: 1. 1968 C code 289-2V engine without air conditioning or heavy duty, or 'extra cooling' option (small radiator). 2. 1969 Boss 302 Eliminator and Mustang. Mustang owners, this 4 blade fan with the part number C6OE-D and (C7AE-F for 1967 and later), is also correct for those K code 289 HiPo engines in both 1966 and 1967. Fan description - 4 blades and 17-1/8 inches in diameter. Ford master part number C6OZ-8600-D. Check out this interesting video...
Availability: Out of Stock, On Order
Item #: 41897 -
These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...
Availability: Out of Stock
Item #: 24080 -
For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part.
For restoration purposes, this bracket was factory painted satin black.
Availability: Out of Stock
Item #: 32879 -
Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...
Availability: Out of Stock, On Order
Item #: 13909 -
High quality alternative to the expensive OEM switch. If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. The only real difference is that this switch does not come with the FoMoCo logo or part number on it. Replaces Ford Part #: C9ZZ-7A247-B, SW 877
Availability: Out of Stock, On Order
Item #: 11805 -
Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.
Availability: Out of Stock
Item #: 11052 -
Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A and C7ZZ-6046-B.
Availability: Out of Stock
Item #: 13983 -
Reproduction Dash to Engine Gauge Feed Harness with the push-on post oil sender for the 1967 and 1968 Mercury Cougar or Mustang with the 390, 427 or 428 Big Block. Replaces Ford Part #: C7ZZ-14289-ACheck out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 32727 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...
Availability: Out of Stock
Item #: 33120 -
NOS fixed column turn signal switch for the 1967 Mercury Cougar or Ford Mustang. This is a later service replacement turn signal switch, it may have an extra wire or two, and the wire lengths may be longer than the factory original. Ford part number C7ZZ-13341-F Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....
Availability: Out of Stock, Discontinued
Item #: 14962 -
Reproduction master cylinder for the Mercury Cougar or Ford Mustang equipped with drum brakes. These are brand new Cylinders, not rebuilt.
Availability: Out of Stock
Item #: 27415 -
Original used speaker lead wiring harness pigtail for all 67 - 68 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the kick panel.*Note - The only difference between this pigtail and the one listed for the 1969-70 dash speaker is the actual plug design.
Availability: Out of Stock
Item #: 32040 -
Reproduction bracket for mounting the rear axle flexible brake hose. From the factory, these brackets were welded in. Double check your placement for your particular year, when welding the bracket to your car. Has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Replaces Ford part number C7ZZ-2A051-A.
Availability: Out of Stock
Item #: 27341 -
This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...
Availability: Out of Stock
Item #: 27342 -
This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...
Availability: Out of Stock
Item #: 27340 -
Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...
Availability: Out of Stock, Discontinued
Item #: 14238 -
Do you want to "feel your music", but don't what a big clunky box in your trunk or back seat? We have what you need! Designed and manufactured specifically for 'under seat' or horizontal 'wall' installations. Compact units with one 5" woofer and piezo tweeter in each enclosure. Under seat fit for 1967 - 1973 Mustang and Cougars. 200 watt capacity! Each enclosure measures 3" high X 8-1/4" wide X 11-1/4" long. Sold in pairs.
Availability: Out of Stock
Item #: 14239 -
Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...
Availability: Out of Stock
Item #: 32848 -
Used radio bezel Grade A used. For use on 1967-68 Mercury Cougar or Ford Mustang cars without console. 2-3 different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.
Availability: Used / Wrecking Yard Item
Item #: 31995 -
1967 289 smog pump adjusting arm, casting number C6OE-9B452-A. Ford part number C6OZ-9B452-A. Application is most Ford and Mercury cars sold new in California in 1966-67. Mercury Cougar only used this thermactor pump adjusting bracket in 1967.
...
Availability: Out of Stock, On Order
Item #: 14353 -
Correct three part, telescoping, round base antenna. Comes with round ridged base gasket.*Customer Feedback* "Aloha Don, The antenna showed up with the rest of the USPS sent items. Got in here in three days. Point of installation of antenna. Tie a string to the plug side of the antenna assembly when pulling out from fender so that you can use the string to pull the new antenna plug back through the fender and into the car. Thought of that after pulling antenna out. I was able to use a flexible...
Availability: Out of Stock
Item #: 27458 -
Factory radio delete or block-off plate from a 1967-68 Mercury Cougar or Ford Mustang. Seldom seen part, roughly 5% of all 1967-68 Mercury Cougars were ordered without any type of radio from the factory. Similar story with the Ford Mustang, most owners added some sort of radio or stereo soon after delivery. The factory radio bezels were made from chromed pot metal, these radio delete plates are made from plastic and vacuum chrome plated. This used example pictured, has most of the plating...
Availability: Out of Stock
Item #: 24885 -
Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.
Availability: Out of Stock
Item #: 24886 -
Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.
Availability: Out of Stock
Item #: 23914 -
Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...
Availability: Out of Stock
Item #: 23925 -
This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head.
Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C
Availability: Out of Stock
Item #: 23931 -
Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.
Availability: Out of Stock
Item #: 20128 -
These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.
Availability: Out of Stock
Item #: 23998 -
1967 390 smog pump adjusting arm, casting number C7AE-9B452-A. Ford part number C6AZ-9B452-C. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same.
Click on images to enlarge.
The...
Availability: Out of Stock
Item #: 23354 -
Bolt that goes through the air pump mounting bracket. Pump rotates on this bolt. Bolt size 3/8"-16 x 4.25" long.
Availability: Out of Stock
Item #: 24314 -
All 1967 390 Cougars with California emissions. Special molded hose see diagram. Connects the smog pump and air inlet assembly.
Availability: Out of Stock
Item #: 11038 -
Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.
Availability: Out of Stock
Item #: 24004 -
Application 1967 289 and 390 thermactor California emissions fresh air inlet assembly or Air pump filter assembly. Ford part # C7AF-9A492-A
Availability: Out of Stock
Item #: 23929 -
Application - 289 with air conditioning and 390 with or without A/C.
Availability: Out of Stock
Item #: 20256 -
Correct for closed emission system Cougars sold only in California. Air cleaner base for both the 289-2V and 289-4V engines. About 17.25" inches in diameter. California emissions with the metal elbow for hose connection to the oil filler cap.
Availability: Out of Stock, On Order
Item #: 41533 -
This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.
Availability: Out of Stock
Item #: 30889 -
Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.
Availability: Out of Stock
Item #: 24083 -
Factory air cleaner base the all S code 1967 Mercury Cougar non-GT or the 6.5 Liter option, 1967 Mustang 390-4V without the GT option, and 1967 Ford Thunderbird with Z code 390-4V or Q code 428-4V engines. California emissions version which has the closed emissions. Note the elbow on the side which attaches with a hose to the oil fill cap.This is the one everyone uses to make a correct 1969-70 428 Cobra Jet ram air or
1967 GT air cleaner base
. This basic bowl design was used by the Ford...
Availability: Out of Stock, Discontinued
Item #: 23316 -
Reproduction scissor jack for any year Mercury Cougar or Ford Mustang. This is a cheap Chinese jack that is clearly marked "For Display Use Only, Not for Lifting Vehicles". It resembles an original scissors jack, but there are several differences. It functions properly and will lift weight, but we wouldn't use it on any of our personal cars. This is the ACME brand like used by Wile E Coyote.
Availability: Out of Stock
Item #: 23872 -
Plate for mounting the spare tire. 4 inches outside diameter with the 3 tabs.
Availability: Out of Stock
Item #: 23768 -
1967 was the last year for the 3/8"-16 threads. We also carry the J bolt C6OZ-1448-A, and the top plate or disc C5ZZ-1424-A.
Wing-nut, spinner. *NOTE* The original 67 wing nut had no protruding tabs in the recessed area as did most of the 1968 - 1973 wing nuts.
Availability: Out of Stock
Item #: 20287 -
Uncommon jack as identified by the coarse threads. This version was made by a specific supplier AUSCO or Auto Specialties Manufacturing Company. AUSCO supplied jacks to Ford until 1970.See the link for the Ford jack research done by Marcus Anghel - Anghel Restorations
Availability: Out of Stock
Item #: 33298 -
New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...
Availability: Out of Stock, On Order
Item #: 26721 -
Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.
Availability: Out of Stock, Discontinued
Item #: 31888 -
New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated stud with correct 1/2 x 20 threads. 1-11/16 over all length, fits 0.61" hole. Replaces Ford part # C3AZ-1107-A.*NOTE* You should use a press to remove and/or install the new studs.
Availability: Out of Stock
Item #: 32189 -
Used clip for mounting the vacuum modulator steel line or tube on 1967-68 Mercury Cougar or Ford Mustang with C4 or automatic transmission. Mounts under one of the top bolts where the bell housing connects to the engine block. This is not a reproduced part, that we know of. The basic Ford part number is 7C072.
Availability: Out of Stock
Item #: 33140 -
New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.
Availability: Out of Stock
Item #: 24393 -
C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...
Availability: Out of Stock
Item #: 32326 -
Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.
Availability: Out of Stock
Item #: 32492 -
Used AQUA passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...
Availability: Out of Stock
Item #: 31876 -
If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available. ...
Availability: Out of Stock
Item #: 31976 -
Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...
Availability: Out of Stock, On Order
Item #: 26694 -
Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...
Availability: Out of Stock, Discontinued
Item #: 12892 -
Reproduction tube seat set for all 1968-70 Mercury Cougar and Ford Mustang. Also some 1967 Cougar or Mustang control valve with the 5/16" fitting. Please note that early 1967 control valves had 1/4" fittings.
Availability: Out of Stock
Item #: 31975 -
Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...
Availability: Out of Stock
Item #: 32073 -
Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...
Availability: Out of Stock
Item #: 24211 -
C7ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Manual steering only, used with SMB-C and SMB-E steering boxes. Ford part number C7ZZ-3590-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below.
Availability: Out of Stock
Item #: 22615 -
Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...
Availability: Out of Stock, On Order
Item #: 13814 -
Pressure die cast, with quality chrome sun visor center bracket and rear view mirror mount. Replaces one of the most visible interior parts on a 1967 Mustang or Cougar. Break away style, two piece construction. Beware of cheap single piece imitations that are available as they are unsafe. Keep in mind you will have to give your screw driver some good pressure when installing to make the mirror fit tight. Replaces Ford part # C7ZZ-17690-A.These are manufactured in the USA. ...
Availability: Out of Stock
Item #: 32488 -
Used IVY GOLD passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer...
Availability: Out of Stock
Item #: 30937 -
Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...
Availability: Out of Stock
Item #: 32484 -
Used SADDLE passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...
Availability: Out of Stock, On Order
Item #: 20118 -
This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...
Availability: Out of Stock
Item #: 12041 -
These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...
Availability: Out of Stock
Item #: 55889 -
These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...
Availability: Out of Stock
Item #: 11968 -
Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...
Availability: Out of Stock, On Order
Item #: 27447 -
Used spacer for the lower windshield moulding, also called an 'anti rattler'. 4 of these plastic pieces were used per car. These spacers were originally installed in the four cutouts in the 1967-68 lower windshield moulding. We won't always have these in stock due to the low survival rate of these spacers. Sold individually.Replaces Ford part # C7ZZ-6503150-A.
Availability: Out of Stock
Item #: 31725 -
Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.
Availability: Out of Stock
Item #: 10851 -
This is a good used fitting with large and small nipples for use with the foot actuated washer pumps found on 1967-68 Mercury Cougar and Ford Mustang. Good used part that we verify the check valve is working. These screw into of the rubber covered pumps.
Availability: Out of Stock
Item #: 41658 -
Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.
Availability: Out of Stock
Item #: 41656 -
Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.
Availability: Out of Stock
Item #: 31394 -
Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...
Availability: Out of Stock
Item #: 14629 -
Premium reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 16 gallon capacity, correct in every way including the drain cock.Replaces Ford part # C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar! ...
Availability: Out of Stock, On Order
Item #: 41857 -
Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...