All Available Parts - 1967 Ford Mustang

D2PZ-8597-A New Old Stock service replacement. Fits 260/289/302 engines from 1966-69. The water bypass hose goes between the water pump and water neck that attaches to the intake manifold.

C0TZ-13A024-A

C5ZA-2454-G or C5ZZ-2454-D New Old Stock manual transmission disc brake pedal pad with stainless steel insert as shown. Application is 1967-70 Mercury Cougar and 1965-70 Ford Mustang, 3 or 4 speed manual transmissions.

C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.

D5DZ-6221812-A

NOS Ford key blank for ignition and doors.C7AZ-622053-A Sold Individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in...

Replaces Ford Part #: C6OZ-3C651-A or (service replacement for) C1AZ-3C651-A

These NOS sill plates always have some degree of shelf wear due to the many years they have been shuffled around. The biggest difference you will see with NOS vs. the two different levels of reproductions is the finish. The NOS parts are far less bright and less prone to showing hairline scratches. One other benefit is that NOS sill plates already have the FORD decal in place. Sold individually.

[No Description Provided]

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

Very rare find... A restored bezel will look fine but will never retain the sharp edges and matte black finish like this new in the box original Ford part.

NOS Back up light switch for the 1967 Cougar or Mustang. Ford Part # : C7ZZ-15520-A

D5DZ-6221813-A Not for XR7.

C60Z-3047-A Used on many Ford products starting with the 1966 Ford Fairlane.

C7AZ-6571-B

C5ZZ-6522600-C

Original or NOS Ford distributor cap.

C5ZZ-13217-B Front parking lamp to body gasket, driver side. 1967-68 Mercury Cougar and 1965-68 Ford Mustang.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the black colored adhesive and is the 5 ounce size.

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

Fuel pump drive eccentric for most big block Ford engines 1963-70. Including 352, 360, 390, 410, 427, and 428. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 3-3/8 inches in diameter. Ford part number C3AZ-6287-A.

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Nice used California emissions air cleaner assembly, includes base with elbow, snorkel, heat riser and air cleaner lid. Application is any 1967 Mercury Cougar or Ford Mustang with C code 289-2V or A code 289-4V engines with closed emissions as sold in California. Elbow on air cleaner connects to the oil fill cap with a rubber hose. All good parts as shown, thermal switch in air cleaner snorkel may not work, and no we cannot test them.Even if you are not currently running all original parts...

Set of reproduction Ford Top Loader 4 speed shift rods for 1967-68 Mercury Cougar or Ford Mustang with 289 or 302 engines only. 

C8ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang. Small block 289 and 302 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. May be either large or small trunion. Subject to availability. Check out our video on rebuilding your shifter below: ...

C7ZZ-7400-C 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Big block 390 engines only. Check out our video on rebuilding your shifter below: ...

C7ZZ-7400-C4Assembly 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Big block 390 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. Check out our video on rebuilding your shifter below: ...

C5ZZ-7400-C3Assembly Factory 3 Speed manual transmission shift control assembly for any 1967 - 1968 Mercury Cougar and 1965 - 1968 Ford Mustang, 1968's only up until 1-2-1968. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our...

1967 - 1968 Manual 3 Speed Shifter Mechanism - Used C5ZZ-7400-C 3 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Check out our video on rebuilding your shifter below: ...

C5ZZ-7210-D "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1967 Mercury Cougar and Ford Mustangs with the 3 or 4 speed shift lever, and 1968 shift levers through 1-2-1968. Bottom bracket only, called a Trunion (see illustration). Measurement of hole spacing is 1-13/16 inches on center. *Note - Must be used with 3 speed shift lever C5ZZ-7210-C, or 4 speed shift lever C5ZZ-7210-M. Check out our video on rebuilding your shifter below: ...

Factory detailing and triple chrome plating distinguish this tubular shift handles from the rest. Cable and T-lever included. American made for quality workmanship. Replaces Ford Part #: C5ZZ-7210-M. Check out this video Check out our video on rebuilding your shifter below: ...

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Good used double sheave alternator pulley.Ford Part #: C5AF-10A352-J.

RUG-E or RUG-E1 Original equipment 4 speed top loader transmission from a 1967 Mercury Cougar with engine code C - 289-2V or engine code A 289-4V only. Ford master part number C6ZZ-7003-B.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...

RUG-M or RUG-M1 Original equipment 4 speed top loader transmission from a 1967 Mercury Cougar with engine code S - 390-4V only. Ford master part number C7ZZ-7003-B.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...

If your 4 speed shifter is broken or wobbly, it's probably time to rebuild it. This kit, when installed, is used to keep tension on the shifter where it connects to the shift linkage, and onto the transmission. Includes insulators, springs, trunions and bolts. Check out our video on rebuilding your shifter below: ...

Single cylinder head from 1967 Mercury Cougar with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current dates include: 7C8, 7C22, Ford casting numbers...

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. These are the GT exhaust manifolds with 14 drilled and tapped exhaust bolt holes. Current dates include: 6F17, 6A11, 6A10 Ford casting numbers...

Single cylinder head from 1967 Mercury Cougar with California smog 289 engines, 289-2V and 289-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 54-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.3:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C6OE-M. *Note - These...

Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

C6ZZ-6582-H Smooth chromed valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 DGS Mercury Cougar and optional on 1965-67 Ford Mustang with 289 engines. Ford master parts catalog shows a right and left version of this cover those numbers are C6ZZ-6582-H & C6ZZ-6582-J. *Note - This is a used chrome valve cover. The plating was pretty low quality back in 1966-67 and these will show rust pitting. For best results we recommend the painted version of this valve cover...

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

The oil filter made by the original Ford supplier.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Crankshaft oil slinger for all FE Ford V-8's, starting 1958 until at least through 1976. 1967-69 390 engines, 1968 427-4V engines, 1968-70 428, 428CJ, 428SCJ engines, 1958-66 352, and 1968-76 360 engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter 3-5/16 inches. Ford part number B8A-6310-A.

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1969 small block, and will work for the 1967 or 1968 with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang /...

Installs between seat track and carpet. These are the same gauge steel as originals. Four per bucket seat, normally only seen on the 1967 model year, will need to be restored. Reproductions work fine, but look a little different. Ford Part # C5ZZ-13190-K

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...

C6OZ-8509-A For any S code 390 engine without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single sheave pulley, 6-3/16 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.Replaces Ford part number C60E-8509-C.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

Used clutch spring bracket that attaches to the brake / clutch hanging bracket. All 1967-68 Mercury Cougar and Ford Mustang with manual transmissions. Replaces Ford Part #: C7ZZ-7535-B.

The tubbing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find these at your local auto parts store or the the "Mustang Discount" folks. Replaces Ford Part Numbers: C7OZ-3A719-A, C7OZ-3A719-C, C7OZ-3A713-A, C7OZ-3A713-C, C7OZ-3A713-D. Please Note: We highly recommend upgrading to the large nut (5/16") control valve as the small nut (1/4") control valve posses a potential safety issue, thus the reason why Ford replaced it the...

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

C6AZ-8509-C 390 engines with air conditioning. Power steering and or thermactor emissions allowed. 2 sheaves with a diameter of about 5-5/16 inches. *Notes say after 1-9-1967 engine build date. Ford casting number C6AE-8509-F.

C6AZ-8509-D Strictly California 390 Cougars without air conditioning. With or without power steering. 3 sheave pulley with diameters of both 5-11/16 inches and 6-1/8 inches. Ford casting number C6AE-8509-J.

Ford casting number C4ME-6A301-A. Single sheave outer pulley for use with power steering as the only option. This pulley is listed in the 1967 engine assembly manual. Listing is for 'Standard Alternator Drive with Power Steering'. Standard alternator would be a single pulley on a 42 amp rated alternator.

C6AZ-6A312-A Two applications on 289 engines. 1. Manual transmissions and standard cooling (standard cooling is the 17 inch radiator). 2. All transmissions with extra cooling (extra cooling is the 20 inch radiator). Dual belt alternator pulley, California emissions permissible. & Without air conditioning or power steering. Ford casting number C6OE-6312-A. Double sheave 67 crank pulley. 6-5/8 inches in diameter.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

Concours correct A/C sight glass hose with a 90° fitting for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.This hose is compatible with both 134a and R12 refrigerants.

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

NOS Air conditioning belt tension pulley for Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968.  Ford part # C7AZ-8678-B. NOTE* Send in your old core for a credit toward the purchase of this NOS pulley. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. Check out this video

[No Description Provided]

New A/C vent hose with cam locks for your Mercury Cougar or Ford Mustang equipped with factory A/C. This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Two required per car, sold as a pair.Ford part #: C7WY-19B680 or B5A-18556-C.

Vacuum tested working hot water valve for Mercury Cougars and Ford Mustangs equipped with factory A/C. This valve stops the flow of warm coolant when the A/C is on and has the original cast brass valve with bracket and vacuum pod. We are unable to guarantee that the water seal is good. Ford part # C7ZZ-18495-A, casting number on vacuum valve C7ZA-18C310-A.

This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.

Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.

Two of these little plastic protectors came on Mercury Cougars and Ford Mustangs equipped with Air Conditioning. They are affixed to the front cross member using the same bolts that holds your condenser in place. Their purpose was to protect the wiring harness from potential damage if the car were to get into a collision. These are very hard to find today as most were discarded the first time the condenser was replaced. Even your most experienced judges usually have never seen or heard of this...

Used rectangular center duct tube for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory air conditioning. Wire reinforced foam, will show some snags or signs of use. Will not have gaping holes. Was originally stapled to the center housing. Ford part number C7ZZ-19B680-B.

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site to all. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember when we used to spend hundreds of dollars for "decent" used examples and then take a risk with...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

OEM Ford stove type bolt for the securing the early style belt tensioner pulley. Used on Cougars and Mustangs produced before 1/3/1967. For use with C5AA-8A919-B Air conditioning belt tensioning pulley.

Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. This 1967 specific wheel is slightly different than the more common 1968-69 stamped steel wheel. Limited to stock on hand. These were offered from 1967 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.

C7ZZ-15520-USED Backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Ford part number C7ZZ-15520-A. *Note - 4 speed switches are different than the 3 speed switches.

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C7ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...