All Available Parts - 1968 Mercury Cougar

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Very rare over the counter, Group II dress up accessory item for any 289 / 302 small block engine. In excellent used condition with no cracks, stripped threads or corrosion damage. The nicest you will ever find. This over the counter Intake was marketed by Shelby American in the Cougar catalog titled "How To Sharpen Your Cat's Claws". Shelby casting number S2MS-9424-A. This intake is basically the same one you so often see with COBRA lettering on it. New to our inventory as of 12-15-2017, the...

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

390 and 427 engines with C6 automatic transmissions. Shaft diameter 3 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory.Ford part number C8WY-4602-B Ask about slip yokes. Shipping is oversized due to length.

Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent. 

This is the original JB Weld. We decided to bring this stuff in as a convenience to you, our customers. Why not buy a pack so that the next time you need to bond something together, you'll have a couple of tubes handy? No need to get up and go to the hardware store. With just a few clicks of your mouse, you can have it at your door in a few days (more or less, depending on your location). Good for all sorts of projects around the house or garage.

Reproduction 15 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction 2 piece spinner assembly for the new HB45 Legendary Series aluminum wheel. The aluminum die cast threaded stem mounts from the back side of the wheel and the chrome spinner truly spins on from the front. Set screw is included to prevent loss. NOTE: Will only fit the HB45 Legendary WheelCheck out our video on Legendary Wheels below: ...

One of the most common problems with first-generation Cougars is droopy hidden headlight eyelids, which make the otherwise iconic front grille look like an eyesore. This inexpensive and easy to install kit provides stops for the eyelids to rest against in the closed position. It also provides some extra structural support to take some of the pressure off the built in bump stops. The vacuum actuators on these cars create extreme downward pressure at all times when running, causing the upper...

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

This reproduction tape is a must for anyone replacing their stainless steel window trim pieces on the 1967 - 1968 Cougar or Mustang. Can be used on any of the side windows. We suggest saving the original quarter window rubber surround if possible, due to the curves, but this tape can be used there as well if needed. This glass setting tape is designed to look and perform similarly to the original Ford factory material. It creates a water tight bond as well as...

This listing is for outer wheel house lower patches, front and rear for the driver side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

This listing is for outer wheel house lower patches, front and rear for the passenger side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

This listing is for the outer wheel house upper patch for the driver side of your 67-68. 

This listing is for the outer upper wheel house patch for the passenger side of your 67-68.  

Used passenger side seat back release catch for the 68 - 70 Cougar or Mustang.

Reproduction deck lid for the 67-68 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid.  Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...

Reproduction upper tube lower insulator for the 1968 Cougar or Mustang column. Used to stabilize the lower end of the steering column. Works on both tilt and fixed columns. Outside diameter is 2-1/8" inches and inside diameter is 1-1/2" inches. NOTE* Ford describes this as an "upper" bearing in relation to the lower steering column tube bearing. It is not used at the upper end of the column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a...

Reproduction taillight panel for the 67-68 Cougar. Yet another in a long line of great fitting parts from our friends over at Dynacorn, this replacement taillight panel is perfect for those of you who have rust holes in and around the taillight area. As seen in the photo above, this is only the taillight panel and will not include the quarter extension panels or the rear taillight lower structure. ...

Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a black background.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels.Check out our center cap installation tips video below: ...

Reproduction castle nut for multiple applications, including the power steering control valve, strut rods, ram cylinder and ball joints on the 1967 - 1973 Cougar or Mustang.  Dimensions: 9/16" - 18.

Reproduction cowl panel for the 67 - 68 Mercury Cougar. This is the upper portion visible from the top of the car.  This panel is unique to Cougar as it does not have the crown in the middle like the Mustang cowl panel has.NOTE! Dynacorn is currently welding the two halves together in house. This makes them almost impossible to install. We have talked to them about just sending the two halves apart and thought they were on board but alas these are still being spot welded together and...

Reproduction grommet that seals the check valve to the Midland brake booster on the 67 - 68 Cougar or Mustang. We also sell the grommet / check valve combo, you can find it here.

Reproduction passenger side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Reproduction driver side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Inglewood, California.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Portland / Beaverton, Oregon.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...

This often times missing bracket was attached to the back of your early 1967 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the less common design.It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend into the rectangular hole to keep the bracket properly anchored to the fragile plastic. For some reason the majority of the cars built didn't get the better...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction burl woodgrain decal for the 1968 XR7G sunroof / fog light switch.

Reproduction coil spring seat pad for the 67 - 73 Cougar or Mustang.  Sold individually, 4 needed per car.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a big block engine. This item requires a $30 core charge.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a small block engine. This item requires a $25 core charge.

Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely.  Replaces item # 31907 Through 67-68, there were four different style brackets, you can see all four...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link.Check out our dash bezel repair video: ...

Reproduction under dash light assembly for the 67 - 68 Cougar or 65 - 68 Mustang. This short style assembly was used on either driver or passenger side. There were two versions of this light, a long bracket version and a short bracket version. The driver side was always the same, but the passenger side typically used the longer version on cars with no A/C. Cars that had air conditioning used the shorter bracket style to keep from coming in contact with the A/C plenum. ...

Used set of 4 toggle switches for the 68 XR7 Cougar dash panel. Included are the toggles for the driver side map light, panel light, passenger map light and courtesy lights. Switches have been tested and may or may not have the tips in place, but we do offer a reproduction set of toggle tips.

Reproduction retainer clip for the back up light switch wiring on the 67 - 69 Cougar or Mustang equipped with a 3 or 4 speed transmission.Replaces Ford part number C7ZZ-14163

Used pair of 31 spline axles for the 68 - 70 Cougar or Mustang, equipped with the Boss 302, 427 and 428 CJ engines all with 9 inch rear axles. Most all other vehicles used 28 spline axles. Short axle 27-1/16" inches long and long axle 31-1/8" inches long. Ford part numbers C9OZ-4234-C and C9OZ-4234-D. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. ...

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

Dark Red / Maroon floor mats for the 67 - 73 Cougar embroidered with the XR7 logo.

Reproduction gold walking cat emblem / insert for the 1968 XR7G T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 68 XR7G, this handle will fit on any 67 - 73 Cougar with an automatic transmission.

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.

Reproduction polished aluminum 600 CFM "Street Warrior" carburetor for the 67 - 73 Cougar or Mustang. Replaces Holley, Edelbrock, Carter AFB, and Autolite style carburetors with 5 3/16" x 5 5/8" bolt pattern. Performance upgrade for stock to mildly modified V-8 enginesCalibrated for excellent street performance right out of the boxFactory preset electric choke for easy startupsVacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing &...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

Reproduction set of idler arm bolts for the 1967 - 1968 Cougar or Mustang.

Chrome screw used to mount the rear interior panel keeper.Sold individually.

Spindle nut kit for the 67 - 69 Cougar or Mustang. This 3/4-16 threaded nut fits most of the 1967-69 brake spindles. The exception would be some of the Boss 302 and some 428CJ equipped cars. Included are nut, cap, washer and cotter pin.

Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.

Dark green floor mats for the 67 - 73 Cougar embroidered with the walking cat logo.

Used roll up door replacement slat. If you damage one you can remove the door, slide the damaged slat off the rubber backer and slide the replacement in. Sold individually.

Reproduction shifter boot for aftermarket shifters on 67 - 68 Cougars, or 64 - 68 Mustangs. Perfect fit for Hurst shifters and will accommodate other aftermarket shifters.   

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Used wiring pigtail that runs from the 14290 under hood harness to the driver side marker light on the 1968 Cougar. NOTE: Wire diagram shows brown and black leads. We've found that most cars have yellow and black. Please note colors you need in the comments section of your order.

Used wiring pigtail that runs from the under hood harness to the driver side headlight harness on the 67 - 68 Cougar.

Used wiring pigtail that runs from the under hood harness at the kick panel to the starter solenoid / horn / voltage regulator on the 67 - 68 Cougar.

Used 1968 Mercury Cougar sunroof motor access panel. This panel is covered by the headliner, but can be dropped down (headliner is glued to the panel) to access the sunroof motor. Will always have a multiple, repairable cracks, but is still functional.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Reproduction wiring pigtail repair kit for the sequential box on the 1968 Cougar.  Included are: 1 four pin red connector1 four pin black square connector1 four pin white square connector1 four pin flat connector 1 two pin connector

Reproduction BLACK lug nut fits all Legendary Series wheels. 14mm x 1.5 threadSold individually. 

Reproduction CHARCOAL lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction 17 x 7 gold haze colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

The Rocket "Strike" provides timeless and classic traditional styling at very affordable prices. The Rocket Strike is a 1-piece wheel precision crafted from A356 aluminum and topped off with a vintage style aluminum o-ring center cap. It has a lug centric design and uses standard 60-degree conical seat lug nuts (sold separately). There is 3.00 inches of hub clearance under the center cap. Load rating is 1560 lbs per wheel.4.25 Back spacingFully polished center and outer rim.  Cast...

Reproduction set of 20 lug nuts used specifically on the Rocket Racing wheels. These lugs will not work on any other wheel.

CURRENT ETA FOR THESE WHEELS IS 2/24/2023 Reproduction 17 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a gold background.  *NOTE - These caps are specifically designed to fit the LW10 series wheels.Check out our center cap installation tips video below: ...

Reproduction Cobra GT 350 center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic blue cobra with red detail.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels.Check out our center cap installation tips video below: ...

This listing includes all parts shown here. It is correct for a 1967 Mustang but for those 1967 Cougar owners looking to delete the tired, warped, peeling old pads this is a great way to clean up a very focal part in your interior. These items can also replace the very hard to find 1968 console parts found in both the Mustang and Cougar but look much different than the 1968 style. Keep in mind West Coast Classic Cougar will take your Grade A 1967 or 1968 used console parts in trade. ...

Reproduction 6.5 litre (390) fender emblem for the Mercury Cougar. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. Unlike the originals these do not have mounting studs, but are firmly held in place with 3M VHT double sided emblem tape.

This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.

Reproduction roof repair kit that includes the roof skin, C pillars and the rear window channel for the 67 - 68 Mercury Cougar. C pillars are cut from our reproduction quarter panels. This kit must ship via truck freight. Expect to pay $400 or more to have these items shipped. Our online shipping calculator is not very accurate for truck freight items so we encourage you not to pay for the order up front but rather bypass paying for your order by selecting "contact us for...

New midland control hub assembly and disassembly tool for use with the 67 - 69 Cougar and Mustang Midland style booster

Used wiring pigtail that runs from the taillight harness ground wire to the K8 / K9 sequential motor. Will work on 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the driver side turn signal harness on the 67 - 68 Cougar Standard and XR7 models.

Used wiring pigtail that runs from the under hood harness pigtail to the driver side headlight harness (brown plug) on the 67 - 68 Standard or XR7 model Cougar.

Used wiring pigtail that runs from the under hood harness to the alternator harness on the 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the horn / voltage regulator / starter solenoid on the 67 - 68 Standard and XR7 model Cougars. Located above the driver side kick panel behind the heater controls. 

Used wiring pigtail that runs from the under hood harness to the voltage regulator ground bolt on the 67-68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the voltage regulator from the starter solenoid on the 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the voltage regulator from the ignition switch on the 67 - 68 Standard and XR7 model Cougars.