All Available Parts - 1968 Mercury Cougar

Premium reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 16 gallon capacity, correct in every way including the drain cock.Replaces Ford part # C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar

Original style wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Replaces Ford Part #: C5ZZ-8287-A.

New replacement gas tank filler cap for all 1967-69 Mercury Cougars and 1970 Cougars without California emissions. This is a vented fuel cap.

New manufactured fuel / gas tank for 1967-68 Mercury Cougar and 1965-68 Ford Mustang, 16 gallon capacity, has drain plug. This is the economy version, which has a slightly different stamping, and is made in Taiwan. Replaces Ford part #C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar

Original style fuel tank installation screw. 3/8 inch hex head. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks. See item 11942 for the kit of 12 screws, better value.

Original style fuel tank installation screw kit. 3/8 inch hex head. This is a set of 12 new screws. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks.

Used factory installed vented fuel, or gas cap as installed on 1967-69 Mercury Cougar 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap.We stock these in limited quantities, and will have an intact paper gasket. Correct "VENTED" embossed and has the "S" stamped onto the center rivet. Price is established by demand, and these normally are only needed for very high level restorations or strict concours judging...

Made from fuel resistant cork like original. This gasket is specific to 1967 - 1968 Cougars. We finally found the correct gasket with correct hole placement (our other version which is good for Cougar AND Mustang has five holes, so basically you would have to drill through the cork just like they did in the Dearborn and San Jose factories).Here's a good tip! Ken Stein gave us this one...Install two of these gaskets and your gas cap will not scratch your paint. Original gas caps will always...

Premium reproduction STAINLESS fuel / gas tank for the Mercury Cougar or Ford Mustang. 16 gallon capacity, correct in every way including the drain cock. Replaces Ford part # C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar

Used license plate holder and fuel door for all 1967-68 Mercury Cougars. Comes as shown, hinges inspected, will include used or new license plate plastic inserts. See our list of related parts, will need rubber bumpers.Replaces Ford part number C7WB-13393.

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

Used original wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Ford Part #: C5ZZ-8287-A.

Used grade "B" tinted rear window glass for the Mercury Cougar coupe that features the "Sun-X" green tint. This unit has multiple fine scratches and water spots and is good for driver or something to "just plug the hole." It is almost impossible to remove even fine scratches from tempered glass. All air conditioning cars were supposed to always come with tinted glass, but we have documented cases of them coming with clear glass. Tinted glass was also available as an option in cars not equipped...

Quality reproduction GREEN TINTED rear window glass that unfortunately does not have original "Carlite" markings or date code. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original.

Satin Finish Wiper Arm

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, but it will fit perfectly as well. We also sell the bedding compound for the installation. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed. Keep in mind this is a common...

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car. The reproductions of the 67 - 70 are identical, but the originals are NOT! The 67 - 68 and the 69 - 70 were bent at different angles and carry different Trico patent numbers. In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style. Click here to see pics of the differences between the 67...

Original stainless steel wiper assembly, fits any 1967-68 Mercury Cougar or Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 15" rubber wiper blade not included.Replaces Ford part #: C3AZ-17528-J.

These zinc-plated Washer Nozzles are exact copies of the originals. Sold in pairs.Replaces Ford Part #: C7ZZ-17603-A.

This is an exact reproduction of the wiper transmissions that will connect to the wiper motor and the output shafts. It includes correct links and pivots for full range of motion. This is commonly replaced when swapping your cowl panel

Injection molded high strength plastic connector for hoses leading to nozzles. Factory fit.Replaces Ford Part #: C7SZ-17A601-A or C0AB-17A601-A.Will not fit 69-70 with factory hoses as they used Ford part # C8OZ-17A601-A

Economy version of the 67 - 68 washer bottle that has the incorrect "stepped down" design on the nipple and no FoMoCo Insignia. Comes with plain cap but we also have good used caps with Mercury Man logo which is correct for the Cougar here.You can find the washer bottle with the correct FoMoCo logo here.Replaces Ford part # C7OZ-17618-A. ...

Exact reproduction of original. Original manufacturer has redesigned blade assembly with plastic components. Sold individually

Replacement bellows for your 67-68 windshield washer foot pedal pump. Over the years

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 390-2V or 4V engines. Updated design from the originals, fuel lines fit the same.

Reproduction gasket for the vintage two piece Carter fuel pump bowl for the Mercury Cougar or Ford Mustang equipped with either the 390-4V, 427-4V or 428CJ engine.

Reproduction fuel filler neck from a 1967-68 Mercury Cougar. Correct for use with factory or reproduction 16 gallon fuel tanks. 

Used grade "B" clear rear window glass for the Mercury Cougar coupe. This unit has multiple fine scratches and water spots and is good for driver or something to "just plug the hole." It is almost impossible to remove even fine scratches from tempered glass.

Quality reproduction CLEAR rear window glass that unfortunately does not have original "Carlite" markings or date code. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original.

Good used windshield washer pump rubber hose assembly

Original FoMoCo used two speed windshield wiper motor for your 1967-68 Mercury Cougar or Ford Mustang. This used motor comes as shown with wiring harness for all 1967-68 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1967-68 installation, must be marked 7Z. Linkage arms sold separately. Stamped C7ZF-17504-D, Ford part # C6OZ-17508-D.

CLEAR Glass without Shade; does not have Carlite logo, perfect fit. We also sell the Window weld for the installation. Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang coupe or hardtop only. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed. Keep in mind this is a common windshield that can be picked up...

Linkage arm that attaches to the windshield wiper motor that is unique to the 67 - 68 Mercury Cougar and Ford Mustang. These are marked 7Z, among other things the slot is specifically indexed for the 67 - 68 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Used wiper transmissions that will connect to the wiper motor and the output shafts. This is commonly replaced when swapping your cowl panel, steel dash panel, and/or firewall. If you want to keep your car original, go with these good used arms, or you can find the reproductions here.

Premium version of the 67 - 68 washer bottle that has the FoMoCo Insignia and correct style nipple. Comes with plain cap but we also have good used caps with Mercury Man logo which is correct for the Cougar here.Replaces Ford part # C7OZ-17618-A.

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

This is a 100% accurate reproduction down to the captured lock washer and black Zinc coating. The only difference is that these are made from a substantially better grade of steel than the originals. These often break when you try to remove them to replace the vacuum actuator so if you are planning on doing that procedure we highly recommend buying these in conjunction with the actuators. Sold individually, two required per car. Cougar part number C7SZ-13A173-A. Also Fits: 1967 Ford...

This is the bolt that often gets destroyed when you try to remove it from the bottom side of the headlight bucket. Our West Coast Cougars come apart a little easier so we often are able to pull them with minimal effort. Cougar part number C7SZ-13A173-A. Application includes: 1967-68 Mercury Cougar and XR7, 1967-68 Ford Thunderbird, 1969-71 Lincoln Continental MK III. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in...

These tension springs are located on either side of your hidden headlamp eyelids. Our springs are made from the exotic alloy "Inconel". Inconel springs have approximately ten times the memory of the originals which were made from the much more common and inexpensive "piano wire". These springs have been engineered to have the exact same elasticity as the originals but will last decades longer than the originals which from our experience with NOS, usually lose their memory within a year and...

This bolt is what adjusts your headlamp cover height. Many people do not know they can rid themselves of that droopy eye look (misaligned grille) by placing new rubber pads on the heads of these bolts and adjusting them. Four required per car, sold individually. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

This single port version was used in the latter part of 1967 and all of 1968. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Cougar part number C7WY-13A185-C headlamp vacuum reservoir.

Used to mate the headlight vacuum hoses together at the front cross beam under the core support. Notice it still has the remnant of green paint used to identify where the color coded hoses are to be placed. Cougar part number C7SZ-13A169-A.

Good used, rust free latch that is in good working order. This unit has not been straightened or pushed out after being in a fender bender. We also have many grade "B" latches in less than perfect condition. We also have the individual components listed. Check out this video ...

Driver side headlight door. If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four Phillips...

This part affixes to the backside of the headlamp cover and acts as a hinge. The design was changed 12-15-67 so you will have to know the date in which your grille was built. All 1967 model year Cougars were built prior to 12-15-67 but we mention this here as many 1967 Cougars have had 1968 replacement parts installed over the years. The brass bushings have been inspected for wear, no collision damage and no rust. Both adjustment bolts are included with the hinge, the bolts in which the hinge...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

New to the market grille fix for 1967 - 1968 Mercury Cougars / Patent Pending. These simple little grille repair clips have been needed since these cars were new! Over the years we have seen a multitude of home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will be listing all the different FoMoCo applications these clips will work on. These clips are sold as a set of four. NOTE: We've found that removing the legs from one side...

C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental 1969 - 1971 Lincoln...

High quality reproduction of the chrome rectangular "corral" emblem surround for the passenger side grille / headlight cover on a 1967-68 Mercury Cougar. Unlike the original, which had the 4 studs peened over on the back side of the grille, this new one attaches with 4 clips (included). See also the background decal and walking cat emblem to make this a complete assembly. We also sell this as a complete kit. ...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

This spring puts tension on the headlight adjusting ring so when you turn the screw on the adjusters the ring remains tight and will move as adjusted. Sold individually, four required per car. These small springs about 0.360" diameter, were used in 1967-68, a larger spring was used in 1969 through 1973, which will fit the early Cougar. Ford number C6SZ-13031-A.

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

These driver quality buckets are solid but will have a small bend, hairline crack or the beginnings of rust in a corner. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in these brackets are very powerful and if these brackets do...

These driver quality passenger side headlight buckets are mostly solid but will have a small bend, hairline crack or the beginnings of rust in the corner closest to the battery. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in...

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they structural integrity...

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Driver side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The design was changed 12-15-67 so you will have to know the date in which your grille was built. All 1967 model year Cougars were built prior to 12-15-67 but we mention this here as many 1967 Cougars have had 1968 replacement parts installed over the years. The brass bushings have been inspected for wear, no collision damage and no rust. Both adjustment bolts are included with the...

Passenger side headlight door.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the passenger side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four...

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. NOTE - If your actuators are the type with the internal spring (Thunderbird actuators had a failsafe internal spring) we cannot accept those as cores. An easy way to tell which actuators are the...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

New black screws for attaching the headlight doors to all 1967-68 Mercury Cougars. Four screws needed per side for a total of 8 per car. We have found 3 different styles of separate screws that were used during the 1967-68 model run, San Jose and Dearborn may have accounted for a difference. This one matches exactly to one of the more common ones that were installed. Replaces Ford Part number 376352-S15.

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford part...

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

This bolt is what adjusts your headlamp cover height. Rare find to still have an original rubber bumper in place that is not compressed or cracked. Four required per car, sold individually. Check out this video

Used, hood latch assembly that is in good working order. This unit will have a bit of metal shifting on the brace portion. Can be straightened fairly easily We also have many grade "A" latches. We also have the individual components listed. Check out this video ...

Used hood release latch by itself, this is a component of the hood latch assembly for any 1967-68 Mercury Cougar.

Used Grade A - Hood latch brace, brace only, fits all 1967-68 Mercury Cougars. Straight piece, this is typically the only part of the hood latch assembly that gets damaged in a collision. This is Grade A used, we also have Grade B braces that need some massaging to be perfect.Ford part number C7WY-16747-A.

Used Grade B - Hood latch brace, brace only, fits all 1967-68 Mercury Cougars. Grade B brace that will need some massaging to be perfect. These are fairly easy to get straight enough cosmetically. We also sell complete assemblies and Grade A used braces.Ford part number C7WY-16747-A.

Used support bracket for the hood latch on any 1967-68 Mercury Cougar. L shaped support bracket goes on top of the hood latch assembly. It also attaches to the radiator core support.Ford part number C7WY-16707-A.

This reproduction spring puts tension on the headlight adjusting ring so when you turn the screw on the adjusters the ring remains tight and will move as adjusted. Sold individually, four required per car. These small springs were used in 1967-68, a larger spring was used in 1969 through 1973.

Pair of reproduction headlight actuators for the 67 - 68 Mercury Cougar. Manufactured to meet and exceed factory specs without the need for additional parts or modification. Keep in mind when you buy these units WCCC will pay $50 for the pair of your rebuildable core units. Our video below explains how to determine if your cores are acceptable. Check out this video on how to rebuild your existing headlight vacuum actuators ...

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable.  NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS.   *NOTE* These...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable. NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS. *NOTE* These parts are far more...

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. Kit includes used check valve and fittings shown, but does not include headlight switch. "I found a good way to...

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Original Ford part number 373845-S.

This bracket attaches the vacuum storage tank for your headlights to the core support inside the driver fender. It differs from the 1967 bracket in that an oval hole was put in it to allow the socket and pigtail assembly for the side marker light to pass through the bracket located closest to the fender. 1969 uses the exact same bracket except for a slightly different clip design. Sold individually, two required per car. Cougar part number C8WY-13B008-A.

Includes all the hardware needed to mount your 1968 vacuum storage can located inside the driver fender. Parts do not come cleaned as shown, we clean many of these used parts so as to show the details and true condition of the part you can expect to receive.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

Good used part with no pitting or obvious damage. Includes stamped steel metal mounting bracket attached to the backside. Headlamp hinge C8WY-13A155-A. Ford part # C8WY-13A137-B. *NOTE* For use on 1968 Cougars built after 12/15/1967. Not for use with 1968 Cougar GT-E. Check out this video ...

Good used eyelid with no pitting or obvious damage. Includes emblem and metal mounting plate. For use with headlamp hinge part # C8WY-13A154-A. Ford part # C8WY-13A136-B. *NOTE* For use on 1968 Cougars built after 12/15/1967. Not for use with 1968 Cougar GT-E. Check out this video ...

Passenger side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The brass bushings have been inspected for wear, no collision damage and no rust. If you try to use a hinge from a 1967 built prior to 12-15-67 it will not fit on your 1968 Cougar. Ford part number C8WY-13A154-A. Check out this video ...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

Reproduction grille mounting kit for the driver (left hand) and passenger (right hand) sides of the Mercury Cougar.

Reproduction rubber hose connector as used on the 1968 headlight hoses. A pair of these connectors connects the color coded hoses that lead to the headlamps from the short hoses coming out of the firewall from the headlight switch. Replaces Ford part # C8WY-13A170-B

Used grade "A" driver side (left hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of large cracks, has good chrome with no pits or major scratches and is not severely warped. Hairline cracks will be present in the area of the painted...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used driver side hidden headlamp hinge. This part affixes to the backside of the headlamp cover and acts as a hinge. The brass bushings have been inspected for wear, no collision damage and no rust. If you try to use a hinge from a 1967 built prior to 12-15-67 it will not fit on your 1968 Cougar. Ford part number C8WY-13A155-A. Check out this video ...