All Available Parts - 1968 Mercury Cougar

Spring nut used to install the fan shroud on a 1967-71 Cougar or Mustang, 4 per car.

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

This complete set of grille bars have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no scrapes so as to qualify for...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

This will really help you understand how your column works! Covers operation, tests and adjustments. All Mustang / Cougar tilt columns were tilt-away in 1967 - 1969. This manual is free for the asking when you purchase a tilt column from us. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most...

Chrome center caps with black background and chrome Mercury man logo.  Came from the factory on 1967 and 1968 Mercury Cougars with Style Steel Wheels, but will work on any 67-70 with Style Steel Wheels.Fits the following models with style steel wheels: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury CougarOther Mercury Cars These caps measure 2 1/2" wide by 9/16" tall. These have been obsolete for many years and often we find deterioration on them even though...

Used grade "C" driver side (left hand) grille section for use as a patch for those with a break in the section that bolts to the center grille. Watch the video below to see how to fix your current grille and save a lot of money.

Used grade "C" Passenger side (right hand) grille section for use as a patch for those with a break in the section that bolts to the center grille. Watch the video below to see how to fix your current grille and save a lot of money.

Used grade "C" driver side (left hand) grille section for use as a patch for those with a break in the section that continues to the fender.  Watch the video below to see how to fix your current grille and save a lot of money. Check out this video

New Cougar Drive-In poster by WCCC! This 20" x 30" poster is printed on heavyweight matte archival paper and features a satin finish. Suitable for framing, this print would make a great decoration in your garage or living room. This photo was taken at our annual Open House event in 2013.Here's a video of our 2013 Open House event! ...

New large black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 21" X 9" X 9" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...

This NOS XR7-G Lucas light lens replacement is a later version that were made by Lucas. They are more correct than the version you will see that are marked "Foreign Glass" but technically not 100% correct in that the say "Made In England" and are marked E11. The originals said "England" in larger letters and did not have the E11 marking. ...

Sold individually these are the very hard to find side marker bulbs for your 1968 Cougar. The 1968 Ford Manuals call for a 97N bulb but that is an error believe it or not... As shown in the NOS light below these bulbs came painted, ALL MODERN REPRODUCTIONS ARE MADE WITH AMBER GLASS (See Amber Glass Listing). The paint is very prone to chipping and after examining several NOS lights that we presume have never been opened we found a couple to have been scratched prior to being installed in the...

This is a NOS clock. The face is brilliant, it has never been mounted and is guaranteed to work good. It does have a tiny crack that is mostly hidden by the center knob which is very common for these original lenses.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

C8SZ-13341-B NOS turn signal switch for 1968 Mercury Cougar, Ford Mustang and Ford Thunderbird. Tilt swing steering columns all without cruise control.

C7ZZ-7528-G NOS clutch equalizer or Z - Bar, or bell crank for 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and either 3 or 4 speed manual transmissions.

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

C9ZZ-2454-A

Very Limited supply. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money. We suggest cutting and pasting your order into an email so we can manually calculate shipping costs.

We have a very hard time keeping these NOS rear lower valences in stock. Since the reproductions don't quite fit right, NOS and good used are the best options at this time.Ford part # C7WY-6540544-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store...

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

Rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors.Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B Check out our...

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock.Thanks for the plug Mark!: My first deal with Don was clear back in the 1980s...

Quality reproduction. Replaces Ford Part #: C5ZZ-7A624-B. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive on 6-13-07 all the way up here in Ontario Canada. That is impressive! Your shipping department is to be commended. I must say that the mail service worked at part of it, but the speed at which your firm addresses online orders from outside your country will keep me coming back for other items! Thank you, Phil...

Excellent fit whether you are installing OEM thickness glass or repro which often is a slightly thinner gauge, must have when replacing either headliner or windshield. There have been multiple manufacturers of this seal over the years, this is the best fit in our opinion. Fits years 67 - 68 for Cougar and 65-68 on the Mustang. We also sell the bedding compound for the installation.  Replaces Ford part # C6ZZ-6503110-A. Keep in mind this is not a difficult do-it-yourself project, here's...

Nice fit! You will need new window gaskets if you plan on changing the headliner. If you are installing the gasket yourself, you will be needing a bedding compound, we like this one here. Replaces Ford part # C7WY-6542084. You can get a feel for what it takes to replace your rear window seal by watching our windshield replacement video. Check out this video

Parking Light Lens Seals are sold as a pair. Fits the 67 and 68. Replaces Ford part #: C5ZZ-13211.

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

These Back Up Light Lens Gaskets are sold as a pair. Fits the 67 and the 68. Replaces Ford part # C5ZZ-15510.

The correct color for the Cougar was gray but many prefer these black Mustang gaskets. Sold as a pair.

These Back Up Light To Rear Valance Seals are Sold as a pair. Fits the 67 and the 68. Replaces Ford part #: C7ZZ-15533. Note, gray is in fact the correct color for these, Mustang used black in 67-68. Note we also have black available for those who prefer.

These pads go between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only. Sold as a pair.  Replaces Ford part #: C8WY-13493 or C8WY-13A493-A. *Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

Replaces Ford part #C8WY-15447. Sold as a pair, two required per car. Right is the same as left.

Sold as a pair. These gaskets seal the lens to the light housing on the 1968 side marker lights found on the fenders of the 1968 Cougar.

Reproduction taillight housing to body seal kit for the Mercury Cougar or Shelby Mustang. Sold as a kit for two lights. Replaces Ford part # C7WY-13520.

Sold as a pair. These seal the lens to the taillight bucket / backing plate. Also used on the 1967 Shelby. Replaces Ford part # C7WY-13461.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

This Accelerator Pedal Rod To Firewall Grommet reproduction fits both the 67 and the 68. Replaces Ford part # C6OZ-9793-A.

This 67 and 68 Firewall To Hood Seal Reproduction has attached rubber studs for mounting. Replaces Ford Part #: C7ZZ-16740.

This Wiper Pivot To Cowl Seal Reproduction is sold as a pair. Fits both the 67 and 68. Replaces Ford part #: C5ZZ-17475.

Unfortunately the premium version is no longer available.  This version is made of a softer compound than the original bumpers and will not hold up as long as the originals did on a Cougar due to the force that the actuator exerts.  Sold as a Pair. Check out this video Check out this video

Reproduction license plate / fuel door cover rubber bumpers for the Mercury Cougar or Ford Mustang. These will also work for the 1969-70 Mercury Cougar or Ford Mustang cowl cover to hood rubber bumpers. Sold as a pair with the mounting screws. *NOTE* These are not an exact replacement, rather a part from another year and application that has been found to be an adequate substitution. If you really need an exact replacement we sometimes can provide a used bumper. ...

Four per car, mounts to fender. Sold individually. Replaces Ford part #: C7WY-16758.

These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

For the in-dash ashtray.

This little rubber part attaches to the top, flat part of your center grille and keeps a small gap between the two panels to prevent paint chips. This is actually an ash tray bumper but it is a decent substitute (a little smaller than the original) for the center grille bumper. The originals had a flat top as opposed to this bumper which has a rounded top. You can find the flat topped version here. ...

Sold individually.

Comes with attaching staples made of stainless steel. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. Replaces Ford part #: C4DZ-16238.Not all cars were assembled with this seal, some came with staples, and others used clips.

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

This kit includes 38 pieces that include quarter panel drain valves.

Sold as a pair. Two required per car.Replaces Ford Part #: 380239.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

These vertical seals attach to the leading edge of the rear quarter windows and seal against the rear edge of the door glass. Sold as a pair.Replaces Ford Part #: C5ZZ-6530146 and C5ZZ-6530147. These are the budget or economy versions. We also sell concours versions.

These are a higher quality rubber than the other reproduction available. Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183

Reproduction door to window seal for all 1967-68 Mercury Cougar and Ford Mustang. Technically though

Complete Heater Seals And Foam Kit. Replaces Ford part #C5ZZ-18500.

Complete foam seal kit for the heater box, flappers, evaporator and heater core on a '67-'68 Cougar or Mustang with factory Air Conditioning. This kit is almost always needed when replacing your heater core.Replaces Ford part #: C7ZZ-18500-A. Check out our video below on how to replace a heater core on a '68 Cougar with A/C! This seal kit is an integral part of the process. ...

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Seals the hole where the A/C lines pass through the core support on the driver side on Mercury Cougars and Ford Mustangs. Replaces Ford part #: C7ZZ-19810.

Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces Ford Part # : C7ZZ-6521449-O Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces Ford Part # : C7ZZ-6521448-O Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Passenger side only. Less than perfect fit, no returns on this item.Replaces Ford Part # C7ZZ-6521448-A Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Reproduction door glass to roof weatherstripping for your Mercury Cougar. These two long strips of rubber fit in the stainless steel channel that begins at the bottom of the A pillar and continues along the roof and ends at the base of the C pillar. Sold as a pair.Replaces Ford part # C5ZZ-6551222.

This is identical to the 67 pad just slightly wider. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part number D3ZZ-2454-A

Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Reproduction brake pedal pad for the Mercury Cougar and Ford Mustang equipped with a manual transmission and drum brakes. This unit is a good fit and is a quality part. Replaces Ford part # C5ZZ-2457-G.

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

These seals the round coffee can sized sized cowl vent to the cowl on the driver side.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

This gasket is found behind the trunk lock housing, which the lock itself sits in behind the trunk lock cover plate, and forms a seal between the trunk lock housing and the trunk itself. Made of soft rubber much like the original. Replaces Ford part #: C7WY-6543625. Check out this video

This 4 Speed Lower Shift Boot attaches to the bottom side of your shifter to protect it from water and dirt. Fits the 67 and the 68 with 289 or 302 engines only Replaces Ford part #: C6ZZ-7138-C.

Clutch Lever Dust Boot for the 289, 302 and 351. Replaces Ford Part #: C6OZ-7513-C.

Replaces Ford part #: C5ZZ-7370. Check out our video on rebuilding your shifter below:

Reproduction Clutch Pedal Rod To Firewall Seal. Replaces Ford Part #: C6OZ-7533.*NOTE* From personal experience we have found these do not stay attached to the firewall as well as the originals. An adhesive will remedy this problem.

Sold individually. Replaces Ford Part #: C7ZZ-3513.

Reproduction antenna base gasket.Replaces Ford part # C5ZZ-18A813-A

This hard plastic part slips over your floor shifter stem and keeps coins and such from falling inside your center console. Replaces Ford part number C7ZZ-7C445-A. Check out our video on rebuilding your shifter below: ...

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

These are the caps placed on the inside of the rear marker reflectors to protect your trunk's contents from damage. These Reproductions are grey. They were originally black with varying shades of grey. Sold in pairs, two pairs per car. Click on images to enlarge. Here is the Rear Marker Reflector without a cap. Here is the new cap on the marker. After you install the Rear Marker, screw the cap onto the Marker from the inside of the trunk. Below is a good used cap on the Marker. ...

High quality rubber molded around a flexible steel insert. Insert is cadmium plated to prevent rust. A popular replacement item, as they always wear. While this unit also fits the 1965-68 Mustang, it is only correct for the 1968 Cougar XR7-G. Replaces Ford Part #: C5ZZ-7D351 Check out our video on rebuilding your shifter below: ...

This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.

This Steering Box Cover Gasket Reproduction fits the 67, 68, 69, and 70. Replaces Ford part #: C3DZ-3581. If your original steering box is one of the few that is still tight then you will want to open it up, clean out all the decades old solidified grease and put new grease in.

New Old Stock side marker lens for 1968 Mercury Cougar and Cyclone Montego. C8GY-15A215-A

NOS C7ZZ-6522428-A Passenger side large size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

This is known as the "K6" relay in the Ford service manual. The function of this relay is to open the circuit between the two instrument panel turn indicator lamps during normal turn signal operation. During emergency flasher operation, the relay points are closed (normal position) and the two instrument panel indicator lamps flash at the same time. Ford Part # C7WY-10B926-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

C7WB-13713-A New old stock XR-7 dash toggle switch for the "Panel" light on the 1967-68 Cougar. This switch has the black plug, and it will work for the "Courtesy" light switch too, those are typically have red plugs though.

Referred to as the "K10" relay in the Ford Service manual. The emergency relay, when energized, maintains through circuits from the motor and cam assembly to the rear lamps. During emergency flasher operation, this relay opens the circuits (normal position) to the inner and outer rear signal lamps. Thus, only the center rear lamps operate when the emergency flasher system is functioning. This unit was originally mounted to the underside of the black cardboard trunk filler board on the driver...