All Available Parts - 1968 Mercury Cougar

Front U clamp sway bar bracket bolt, for any 1967-68 Mercury Cougar or Ford Mustang. 3/8-16 x 1.0 Grade 5 bolt. Sold individually, 4 per car. part #20408-S

Reproduction steering gear box bolt. Sold individually

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

part# 384114-S100 Sold individually Check out our caliper tips and tricks video below: ...

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish.  Ford Part # 382486-S.

replaces Ford part # B-12764

Replaces Ford part #375381-S Phosphate & Oil Finish

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang.Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws -  375694-S2

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a B and others had no stamping at all. 13/16" hex head, 1-1/2 inch bolt with a 3/16 inch shoulder. 

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a F and others had no stamping at all. 13/16" hex head, 1-7/16 inch bolt with a 1/4 inch shoulder. 

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Hex head screw for attaching floor drain hole covers. Several different screws were used over the years and at different plants. All seem to be a #8 sheet metal screw of varying lengths. This is a #8 hex washer head tapping screw with 5/8" length. Two screws per drain cover, 2 or 4? per car, not sure. We also have the drain covers. 

Reproduction mounting kit for the center grill for the Mercury Cougar. Check out this video

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.

Multiple uses.5/8" from bend to center hole.

Used for multiple applications. 7/8" from bend to center hole.

Reproduction clip for the rear quarter extension moulding / trim on the Mercury Cougar. The rear quarter extension moulding / trim uses 2 different size clips. This is the smaller of the two. One per side, 2 per car. Get the larger clip here. Replaces Ford part # C7WB-65291B80-A. *NOTE* Will work with the 1967-70 trunk trim, but the nuts are wrong style.

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Check out this video ...

Bag of 25 reproduction j-nuts for the front fenders on the Mercury Cougar or Ford Mustang.5/8" from bend to center hole.

Good reproduction of the 1967 throttle rod for 289 engines. It will fit on 1968 with any 289 or 302 engine with Ford Autolite carburetors. Will also fit most Holley and Edelbrock carburetors too. We also sell used versions of both 1967 and 1968 small block throttle rods. Consider also purchasing a linkage clip, see related items.Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all...

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with 289 or 302 engines. Ford part number C8ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Clip for mounting the throttle linkage rod rod to the carburetor and mounts C-4 or C-6 throttle cables to the throttle bell cranks.Replaces Ford part number C2VY-9826-A.

Reproduction concours correct throttle return spring bracket for the Mercury Cougar or Ford Mustang equipped with the 390GT engine. This bracket is shorter in length than the 390-4V piece.Ford part number C7OZ-9741-B.Also good for 1968-1/2 - 428CJ.

Correct texture Gas Pedal, includes stainless steel trim.

Black moulded plastic pedal pad for all 1967 and 1968 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C5ZZ-9735-A.

Stainless steel throttle pedal surround trim. Self attaching to part number C5ZZ-9735-E. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up.Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with manual transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always superior.Ford...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block Cougars with automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any factory Cougar V8 engine. 289, 302, 390, or 428CJ Cougars with manual transmissions.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 390 or 428 Cobra Jet FE big block 1967-68 Mercury Cougar and Ford Mustang with automatic transmission.Ford part number C7ZZ-9725-A.

Used on the retractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Ford part number C8WY-9A702-A *Note - Before 12/11/1968. *Note - not for use with factory cruise control.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with C-4, automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always...

Add this to your cart to receive a link to download it upon checkout.

This A/C tag clip fastens the aluminum tag to top of the A/C pump.

Core used set of Eaton clutch brushes, we save these because of the FoMoCo stamped bracket with Ford part number C7AA-2979-A. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to reproduction version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for NEW Eaton brushes. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This reproduction OE steel power disc brake line kit for 1968 Mercury Cougar equipped with the 8 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders.

This reproduction steel power disc brake line kit for Mercury Cougars equipped with the 9 inch rear end with 28 spline axles is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders.

This reproduction stainless steel power disc brake line kit is for the Mercury Cougar equipped with the 9 inch rear end and 28 spline axles. It is item is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

This reproduction OEM steel power disc brake line kit for Mercury Cougar is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders. It does not include the flex tubes. Originally optional only on R code, GT-E, Cobra Jet, and Boss Eliminator.

This reproduction stainless steel power disc brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rearend and 31 spline axles is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper. Only an option on R codes, GTEs, Cobra Jets and Boss Eliminators.

This reproduction stainless steel power disc brake line kit is for the Mercury Cougar equipped with the 8 inch rear end and 28 spline axles. It is item is bent and drop-shipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubesthat connect to the caliper.*Customer Feedback*"Just wanted to thank you guys, found your incredible website and ordered your brake line kit and...

This reproduction standard drum brake line kit is for Mercury Cougars equipped with the 8 inch rear end and 28 spline axles. It is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction stainless steel standard drum brake line kit is for the Mercury Cougar equipped with the 8 inch rear end and 28 spline axles. It is item is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

This reproduction stainless steel standard drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction OE steel standard drum brake line kit for Mercury Cougars equipped with the 9 inch rearend with 31 spline axles is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

This reproduction stainless steel standard drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rearend and 31 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction power drum brake line kit is for Mercury Cougars and Ford Mustangs equipped with the 8 inch rear end and 28 spline axles. It is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

This stainless steel power drum brake line kit is for the Mercury Cougar that is equipped with the 8 inch rear end and 28 spline axles. It is item is bent and dropshipped from the supplier when it is ordered and is available in OE steel or Stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction steel power drum brake line kit for Mercury Cougars equipped with the 9 inch rear end with 28 spline axles is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connects to the calipers.

This reproduction stainless steel power drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction steel power drum brake line kit for Mercury Cougars equipped with the 9 inch rearend and 31 spline axles is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes the connect to the caliper.

This reproduction stainless steel power drum brake line kit is for Mercury Cougars and Ford Mustangs equipped with the 9 inch rearend and 31 spline axles. It is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

[No Description Provided]

Replace those rusty, failing brake lines with these Reproduction Stainless Steel Front Power Brake Drum 5 Line Set for the 1967, 1968 and 1969 Mercury Cougar

Also Correct for some 1967 models with proportioning valve at front

Also correct for some 1967 models with proportioning valve at front

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

Replaces Ford Part # C7SZ-3D600-A. Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 9/16" thick.

New product that is in stock and ready to ship! Unlike 1968 the 1967 xr7 console indicator light bar had no woodgrain applique. This will work fine on your 68 and some prefer the 1967 look over the 1968 version. We have a few of these with a 1968 Burl Wood Overlay applied to them. If you would like one of these, mention it in the order notes and if we have any remaining will send you one of these. These two pictures give you an idea what the lights will look like when illuminated. When not lit...

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

This emblem was located on either side of the quarter panel in 1968 and both front fenders in 1971 - 1973. The studs on the 71-73 were a little longer but this 1968 emblem is an excellent substitute. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very consistent. The plating is very inconsistent on the original Ford emblems. We are very excited to...

New product that is in stock and ready for shipment now! Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C'...

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5-16", a clutch diameter of 6", and an overall thickness of 2 inches. This version uses the Eaton style of brush, which is available new.Ford part # C7AA-2981-G.

Due to corrosion caused from the exhaust this used emblem will most likely have poor quality chrome. The emblem shown would be the very rare exception.

Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar

Two required per car, right is the same as left. Good used Cougar emblem with no pits, deep scratches or broken studs.

Used Grade "A" Grille Center Medallion for the 1967 and 1968 Mercury Cougar. These will not have pits or damage to the chrome. Unfortunately the softer black background insert will often times have marks. Ford part # C7WB-8B344-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

What a difference a few minor blemishes can make in price! Our grade "B" used centers will always have a few minor dings as shown and maybe some very minor pitting in the painted part but after some clean up they will look almost as good as our grade "A" units when viewed from several feet away. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Reproduction Center Grille Insert Background Decal for the 1967 and 1968 Mercury Cougar. This insert will need to be shaved down on 2 sides to fit correctly, do not force the insert into the grille, it will pooch up in the middle and not adhere correctly. The aluminum Mercury Man emblem can be popped out from the rear with a solid hit with a drift punch and hammer without causing damage. Check out our video, showing how to install this decal, along with some other handy grille restoration tips ...

NOS Emblem for the C pillars and RH headlight door of your XR7-G. These are made by the same company that made them originally in 1968! These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Click on images to enlarge. FOR IMMEDIATE RELEASE .....Famous race driver Dan Gurney wrote the formula for a new type of personalized sports car -- the Cougar XR7-G -- which will be introduced at Lincoln-Mercury dealerships in early...

Good used "C" pillar emblem for your XR7 with no obvious pitting. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.Ford part number C7WY-6528818-B1 Hi Don: Thank you for fixing me up with the XR-7 pillar emblems. I appreciate doing business with you. It's nice doing business with guys who are not perfect, but try to be and correct anything within reason that is called to their attention. Take care, Greg Worth TN ...

These were originally painted argent silver with the back ground painted semi-gloss black, they were not chromed. This emblem was used on all 1968 Cougar steering wheels with the exception of the XR7-G.

Used 6.5 litre Grade A (390) fender emblem for the Mercury Cougar. We rarely get these in fantastic condition and most of what we get looks like the one pictured on our grade B listing with several minor blemishes. No studs will be broken off due to someone thinking they pry off as opposed to being held on from the backside with speed nuts. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the...

Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your used corral (or rectangle frame) remounted after you break off the studs to remove the assembly. Replacing this emblem assembly is probably (for the money) the best way to improve the looks of the...

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...

These are sold as a pair and are of marginal quality. The material is much softer than original, the chrome is of a low quality and compared to original the detail is not nearly as crisp. Check out this video

Unlike previous reproductions, these have the correct magenta red background and raised lettering.

Correct original windshield washer reservoir cap with "Mercury Man" logo. All the replacements are plain as was the Ford products that used this same cap configuration. Ford part number C7AZ-17632-A

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

This decal was used on the Standard model Mercury Cougar for 1968 and both the XR7 and Standard model Mercury Cougar for 1967. Will require slight trimming for perfect fit. If you place a piece of 80 grit sand paper (or file/emery board) on a firm surface you will be able to bring the height of the decal down with just a few strokes of both the upper and lower edge. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive...

Very correct looking reproduction used only on the 1968 XR7 Mercury Cougar. This decal may need slight trimming to fit perfectly into the recessed portion of your lock cover. Check out this video

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

These Mustang emblems have the incorrect pin placement for the 1968 Cougar so if you have original GT fenders you will have to drill new holes. Once mounted they look correct. Replaces the C7ZB... individual casting numbers. Licensed by FORD

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. Check out this video

This is for the person who already has a decal or XR7G emblem to place in the center section. Maybe you have a custom idea? Same great quality and flawless fit as our other deck lock covers. *NOTE* After a long hiatus these are finally back in stock! They were worth the wait, the quality is really good on this new reproduction. Check out this video

Great quality for the money, but you will have a gap showing around the perimeter. When looking at the backside of these XR7-G emblems, you will see the green vinyl backing on the two sided tape. A NOS emblem, (original emblem sold by Ford) will have green paper backing. These are not technically a reproduction as they are made by the OEM supplier. Click on images to enlarge. Notice the gaps when installed on our reproduction deck lock cover. Here are some pictures on the new emblem side by...

Save your hard earned money when you buy our reproduction deck lock cover with the new XR7-G emblem already installed! Check out this video

These always are peeling. Located on the right side on the dash face...