All Available Parts - Other Ford/Mercury

Cork Oil Pan Gasket for the 351 Cleveland Cork Oil Pan Gasket in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

OEM style cork oil pan gasket for the 429 Cobra Jet on the 1971 Mercury Cougar or Ford Mustang.

Used oil screen pick up tube assembly from a 1969-70 Ford Boss 302 engine. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes.  * Excludes regular 289/302 engines. Replaces Ford Part #: C9ZZ-6622-A

Used oil screen pick up tube assembly from a 385 series big block Ford 429 Cobra Jet or 429 Police engine. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes.  * Excludes regular 429 / 460 passenger car engines, and all F Series pickup trucks, which have rear sump oil pans. Replaces Ford Part #: D0OZ-6622-A ...

Oil filler cap elbow for hose that goes to the air cleaner elbow. Black plastic like original, fits 1968-70 Mercury Cougar and Ford and Mustang. See related items for grommet and other related parts.

Spark Plug Wire Separator Brackets for the 1969 - 1970 Mustang Cougar or Torino with 428CJ Finned Aluminum Valve Covers, 1969 - 1970 Mustang Boss 302 with Finned Aluminum Valve Covers or Boss 351 models. These are an MCA approved unit made here in the USA. These replace Ford part number C9ZZ-6583-A and include both brackets and the 4 screws to properly install these units. Attaches spark plug wire holder to the factory finned aluminum valve covers

Finned aluminum Ford cast valve covers for any 1970-71 Ford or Mercury with 429CJ engine. Almost correct on 1971 Mercury Cougar and Ford Mustang with N or C code 429CJ engines. D0OE-6583-A is the part number cast on both. These both have the same opening for the oil filler cap on both sides. Technically, for 1971, the passenger side cover would have a round hole for the PCV grommet and have a D1OE-6583-CA casting number.

Used timing chain cover with casting number C5OE-6059-A, for any 1965-67 289 engine. 1967 Mercury Cougar and 1965-67 Ford Mustang. This timing cover has a built in timing pointer as part of the casting. Cast aluminum construction without excessive damage. Find the installation bolt kit here. Replaces Ford part number C5OE-6059-A.

Used timing chain cover with casting number C3AE-6059-A, for any 1967 390 engine. 1967 Mercury Cougar and 1967 Ford Mustang. Cast aluminum construction without excessive damage. Installation bolt kits also avialable.Replaces Ford part number C3AE-6059-A.*Note there is a different version of this timing cover for 1968-70 390/428CJ engines.

Used timing chain cover for any 289 / 302 / 351W engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968 Ford with 289 or 302. Cast aluminum construction without excessive damage. Installation bolt kits also available. Sometime during the 1969 model year, the timing chain cover number changed to C9OE-6059-A. So either one will interchange. Replaces Ford part number C8AE-6059-A.

100% Concours Correct PCV Tube for the 1968 Mercury Cougar 427 GT-E, Ford Mustang, Fairlane, or Torino with the 428 Police Interceptor, fits either # C6AE or # C7AE Aluminum PI intake manifold. Replaces Ford Part #: C6AZ-6758-B.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

Hot idle compensator valve assembly for many Ford engines with PCV, starting in 1964 through early 1968. Typically found on 1964-66 Ford 260-2V, and 289-2 engines with air conditioning. 1967-68 289-2V, 302-2V and some 390 engines all with air conditioning and PCV or closed emissions. The Ford assembly manual indicates that the Hot Idle Compensator Valve 'T' Assembly, was installed by removing 3/4 inches of the PCV hose, 2-1/4 inches (on center of the PCV valve). See picture for clarification....

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

Used plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.

Used early version short seat belt mounting bolt to mount the front retractor to the inner rocker panel and used in conjunction with a large washer. This is an early version of the the seat belt bolt with faint or no markings on the head, the later versions are longer, and have much more prominent head markings.13/16" hex head, 1-1/8inch bolt with a 3/16 inch shoulder.

Used early version of the long seat belt bolt for the Mercury Cougar or Ford Mustang. This early version has faint markings on the head of the bolt as where the later versions have more prominent markings. 13/16" hex head,  two inch bolt with a 1/2 inch shoulder. Can be either smooth headed or have an "E".

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. These manifolds are available in both early and late versions. The earlier version manifold has the correct spacer on the right side while the later version manifold does not.  Installs easily and eliminates clearance issues compared to headers....

Known to have been used on 1969-70 air conditioning boxes to hold a vacuum hose.Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.

New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.

New Bolt kit, for the installation of a water pump on any Ford 351C or 351 Cleveland engine. Fits all 1970-74 Mercury Cougar and Ford Mustang with 351C, 351CJ engines. 11 total pieces in the kit as shown.

New Bolt kit, for the installation of a water pump on 1970-73 Ford 302, Boss 302, or 351W engine. Fits all 1970 Mercury Cougar and 1970-73 Ford Mustangs. 9 total pieces in the kit as shown.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.

Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

Repro fuel pump gasket for 1967 - 1970 Cougars or Mustangs with 289/302/351W/390/428CJ engines.

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4193S. This is the early style with "CAR bure TER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with A or C code 289 engines and 1966-67 Ford and Mustang with A or C code 289 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4194S. This is the early style with "CAR bure TER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with S code 390 engines and 1966-67 Ford or Mercury with S code 390-4V V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4567S. This is the early style with "CARTER" and USA, has the 3/8" fuel nipple. Correct for 1968 Mercury Cougar with C, F or J code 289 / 302 engines and 1968-69 Ford and Mustang with 289 or 302 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4567S. This is the early style with "CAR bure TER" and Canada, has the 3/8" fuel nipple. Correct for 1968 Mercury Cougar with H or M code 351 engines and 1969 Ford and Mustang with 351W V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4385S. This is the style with "CARTER" and USA, has the 3/8" fuel nipple. Correct for 1968-69 Mercury Cougar with X or S code 390 engines and 1968-69 Ford and Mustang with 390 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible dates, we will...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4193S. This is the late style with "CARTER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with A or C code 289 engines and 1966-67 Ford and Mustang with A or C code 289 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4194S. This is the late style with "CARTER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with S code 390 engines and 1966-67 Ford or Mercury with S code 390-4V V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible dates, we...

Nice reproduction of the D0OZ-17C583-A windshield wiper stop as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Zinc plated and rubber dipped like OEM Ford. Replaces Ford part number D0OZ-17C583-A.

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction Quarter window stops.  Mounts onto quarter window to limit upward travel within the channel. Each quarter window requires two of these stops. Fits either driver side or passenger side quarter window. For Coupe or (Mustang) Convertible body styles. Bolt included. Replaces Ford Part # C5ZZ-6529968-A Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video below: Check out our handy diagram below to find other '67-'68 door parts...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

Nice thick foam. Chromed mounting post. Includes base plate for seat. Keep in mind we have good used for less money, several colors available in good condition. Find them here.

These 1969 molded vinyl, single post head rests were never offered on a Cougar or Mustang to our knowledge but they make a great "go-around" for the very expensive 1968 dual post headrests. To use them on your 1968 Cougar you will first need a pair of 1969 bucket seats as they have the internal hardware to accept the post. 1968 was a weak design so the 1969 seat frame is a nice upgrade and of course will accept any of the 1968 foam and interior kits. These headrests when in the down position...

This is the arm rest base for the driver or passenger side on any 1971, 192 or 1973 Mercury Cougar with standard interior as well as some Mustang trim levels.  Also fits multiple other Ford /  Mercury cars of the same vintage.Replaces Ford Part Number: D1AB-5724144

Used chrome end for the grab handle found on Mercury Cougar XR7 and several other Lincolns like the Continental MK III. Seldom will these be perfect, most have some pitting on the top sides. Fortunately they can be switched end for end and the pitting side can be installed downward. These units are sold individually.Mercury part # C9MB-5422668-A or D0MB-5422668-A.

Reproduction of the 1969-70 Mercury Cougar XR7 door panel door grab handle or door pull ends and caps. Also found on 1969-70 full sized Mercury cars and 1968-70 Lincoln Continental MK III. Chromed end originally had a Mercury part number of C9MB-5422668-A, and the flat covers had a part number of C8MB-5422678-A. Nice reproduction of the covers, although we feel that they are a tad too shiney. Sold in a set of 8 pieces, enough for two door pulls.

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

If you have already begun to install or have installed this item, it is not eligible for return or refund. This rim blow horn switch is made in the United States by Daniel Carpenter Mustang and is made from vinyl like original. When installing, make sure to massage the rim blow switch in place with counter clockwise, compacting strokes. Clockwise strokes (thumb motions) will stretch the switch and when you complete the installation you will find the part has become too long to fit in place...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is a fully functional retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing, good chrome on the male buckle and it may even have the date code tag still in place. We will try to obtain the correct date code...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is a fully functional retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing, good chrome on the male buckle and it may even have the date code tag still in place. We will try to obtain the correct date code if...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged.  Check out our video "All about seat belts" below. ...

Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A

NOS Standard seat belt retractor including bolts and a huge 44" x 33 1/2" Ford seat belt diagram in FoMoCo box and never installed on a car. Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models.  NOTE: Front retractors are same for left and right. Check out our video "All about...

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

Both deluxe and standard used the same retractor in 1968 - 1969 and left is the same design as right. Grade "B" retractors will be 100% functional but cosmetically will show a crack in the plastic holster, and may have minor rust on chrome. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Check out our video "All about seat belts" below. ...

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. We have glass bead blasted rust from inside, chrome is not perfect but part is functional. Originally came stamped ROBBINS - JR - 7600 or HAMILL H-000, we randomly pick them for you, no guarantee as to which supplier yours will have originated from.

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

Pit free original rear console courtesy light for all consoles 67-68, does not usually come with a good lens as most are cracked, faded or missing. Casting number as seen on the back reads C7ZB-13743-A. Number imprinted on wire can be: C4VB-13757-A.

Reproduction rear courtesy / opera light lenses for the Mercury Cougar. The rear courtesy / opera lights were standard equipment on all XR7 Cougars, but were a popular option many other standard and decor level interior Cougars. If your car did not originally come equipped with them, it is actually quite easy to install them, but you will need to purchase our used housing /socket assemblies. These are fantastic quality and a perfect fit. Sold as a pair only. Ford part # C6VB-13B726-A. *TRIVIA*...

This manual shows exploded diagrams and part numbers of all the motors Ford used in 1967, not just the Cougar. I use this manual almost daily for identifying air conditioning brackets and various pulleys.

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages.

Manual on how to modify your FE big block Ford for street or strip.

Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.

Complete reprint of 11 Supplemental Off Highway Performance Operation Parts Newsletters from Ford which were printed between January 1972 and Spring of 1973. Full of tips on modifying your vehicle for Drag, Strip and Oval Racing.

Comparative Guide of the 1970 Ford Performance Vehicles and the "Competition", which included the Cougar.

Great color brochure showing the full line of Ford products.     ...

Complete reprint of the 1967 Vacuum Schematic for the Mustang. If you would like we can include a copy of the Vacuum Schematic for the Cougar Vacuum Headlight System from the Ford Master Parts Catalog. This is for Mustang so it will not show the Cougar but will work for the vacuum system. Mustang and Cougar were the same with the exception of the headlights.

Complete reprint of the 1967 Vacuum Schematic for the Mustang. If you would like we can include a copy of the Vacuum Schematic for the Cougar Vacuum Headlight System from the Ford Master Parts Catalog.

NOS New Old Stock oil dip stick tube for any 1968 Mercury Cougar or 1968-69 Ford or Mustang with 289 or 302 engines. Bare steel tube. Scott Drake makes a very good reproduction of this item for much less money. See related items.Ford part number C8AZ-6754-A.

NOS New Old Stock air conditioning fixed idler pulley for all 1967 Mercury Cougar and Ford and Mustang, all with 390 engines. Ford part number C7SZ-8678-B.

New Old Stock speaker for the 1967 - 68 Cougar or same year Torino. This is the speaker that fits inside the speaker pods situated behind the kick panels. These speakers are tested and in good shape with no tears on the cones. Good for the Cougar enthusiast who wants to keep their car as close to original as possible.Ford number C7OA-19A067. Sold individually. ...

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used bracket for mounting a steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Main bracket only, there is also a side support bracket that is also needed. Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Tilt and fixed steering columns.Ford part number D0AZ-3676-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3676-A.

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

Used flat headed stove bolt and nut, for attaching the two steering column mounting brackets together. Brackets for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Two needed per installation, sold individually. This is a 3/8-16 square neck bolt and nut. Ford part number 384527-S2.

Used jumper wire that connects the tilt-a-way door jamb and to the underdash harness.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.