Home > Other Ford/Mercury
All Available Parts - Other Ford/Mercury
Products (Click sub-categories above to ONLY display results for that Sub-Category) 101-200 of 513
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 10721 -
Manufacturer calls this a torque pin kit, it consists of 3 pins. Pin diameter is 1/2 inch and are 13/32 inches long. Made from natural nylon. Fits most Ford vehicles with power windows from 1964 - 1973+.
Availability: In-Stock Item
Item #: 11348 -
Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...
Availability: In-Stock Item
Item #: 14193 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...
Availability: Used / Wrecking Yard Item
Item #: 20704 -
Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.
Availability: In-Stock Item
Item #: 10017 -
This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit
Availability: Discontinued
Item #: 14026 -
Dash to engine Gauge Feed with push-on post oil sender and Air Conditioning. Should be for 1966 Falcon and Mustang. Replaces Ford Part #: C6DZ-14289
Availability: In-Stock Item
Item #: 32101 -
New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.
Availability: Out of Stock
Item #: 22545 -
Used switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and black knob marked "DEFOG". Replaces Ford part number C8ZZ-18578-A.
Availability: Used / Wrecking Yard Item
Item #: 16745 -
Used service replacement switch for the rear defog or defogger fan on any 1968 Mercury Cougar or Mustang coupe or hardtop. Original Aetna manufactured switch with the three prongs on back. Tested and working two speed switch. Comes as shown with mounting bracket and chrome knob, bezel is marked "DEFOG" as shown. *Note - this is not the OEM 1968 defog switch, it is the switch used in defog kits starting in 1970 for many Ford and Mercury dealer installed or over the counter kits.Replaces Ford...
Availability: Out of Stock
Item #: 22952 -
Rear defog conversion kit for any 1968 Mercury Cougar or Ford Mustang Coupe. Includes switch with bracket that goes under the edge of the dash, wiring harness to the accessory plug (for sure on all 1968 Standard and XR7's), long harness to blower motor, and blower motor and grille cover which installs in the rear package tray. Please see your electrical schematic for connection details. Everything has been tested to be in working condition. *NOTE - Early 1967 Cougars do not have the proper...
Availability: Used / Wrecking Yard Item
Item #: 16174 -
Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...
Availability: Used / Wrecking Yard Item
Item #: 12929 -
Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in most 1970-72 Mercury Cougar or Ford anything including Mustang. Can be used on any 1970-74 351C engine from Ford. Technically, 1972 California 351C cars and 1973 351C cars used a different timing pointer for what ever reason. Replaces Ford part D0AZ-6023-A.
Availability: Used / Wrecking Yard Item
Item #: 12999 -
Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1968 Mercury Cougar and Ford Mustang with 390-2V, 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Reproductions are nice, but they are a copy of the 1969-70 timing pointer. Close, but no cigar. Replaces Ford part C8AZ-6023-A.
Availability: Used / Wrecking Yard Item
Item #: 13137 -
Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1969-70 Mercury Cougar and Ford Mustang with 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Replaces Ford part C9AZ-6023-A.* Note 428 Super Cobra Jet uses a different pointer, see related.
Availability: In-Stock Item
Item #: 32401 -
Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.
Availability: In-Stock Item
Item #: 33003 -
Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.
Availability: Used / Wrecking Yard Item
Item #: 33595 -
Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A.
Availability: Used / Wrecking Yard Item
Item #: 33596 -
Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A,
Availability: Used / Wrecking Yard Item
Item #: 13468 -
Used stamped steel pointer mounts to timing chain cover. Correct for 1967 Mercury Cougar or Ford Mustang with S code 390 engine. Must be used with the 1967 style timing cover.
Availability: Used / Wrecking Yard Item
Item #: 32091 -
Fuel pump drive eccentric for Ford 351C engines 1970-74. Used eccentric from our wrecking yard. Includes inner and outer eccentrics, bolt, and washer. 2-1/2 inches in diameter. Ford part number D0AZ-6287-A.
Availability: Out of Stock
Item #: 32221 -
Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP
Availability: In-Stock Item
Item #: 32361 -
White reproduction fan for the Thermactor Smog Pump.
Availability: In-Stock Item
Item #: 32394 -
Bolt kit for installing the idler and adjusting pulley on any 1970-71 Ford Torino / Mercury Cyclone, or 1971 Mercury Cougar / Ford Mustang with 429/429CJ engines. 4 bolts 3/8-16x7/8 inch washer head bolts.
Availability: In-Stock Item
Item #: 32393 -
Bolt kit for installing the idler and adjusting pulley on any 1968-69 Mercury Cougar / 1968-69 Ford Mustang or 1968-69 Ford / Mercury with small block 289 / 302 / 351W engines. 4 bolts 3/8-16x7/8 inch washer head bolts.
Availability: In-Stock Item
Item #: 16748 -
Quality wiring reproduction for Perfect Circle brand of speed controls as found on most 1967-1971 Ford - Mercury - Lincoln automobiles. Main harness with Ford part number 9A840, can be used on a variety of model and years. Harness connects the servo, has grommet for firewall, and connectors under the dash. Jumper wire to the brake pedal.
Availability: Ships Direct from Supplier (Except International)
Item #: 17763 -
Exact Reproduction 289 Hi-Po Main Cap Set offered by Ford. They are cast and machined here in the USA from the original Ford blueprints. A set consists of caps numbered 1- 4 and requires the use of an original rear main cap to finish an engine. These caps are cast from the highest quality Nodular iron and machined for ease of fitting to any 289 block. The I.D. of the main bearing bore is .020 undersize and the side registers are .010 oversize on each side for proper adjustment before line...
Availability: In-Stock Item
Item #: 41714 -
Concourse Correct Timing Pointer for any 428 Super Cobra Jet Replaces Part Number C9OZ-6023-A.
Availability: Used / Wrecking Yard Item
Item #: 13465 -
Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...
Availability: Used / Wrecking Yard Item
Item #: 18866 -
Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...
Availability: Used / Wrecking Yard Item
Item #: 16158 -
Single cylinder head from 1967 Mercury Cougar with 390-4V engine with California thermactor smog ports. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current...
Availability: Used / Wrecking Yard Item
Item #: 16122 -
Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...
Availability: Discontinued
Item #: 16746 -
Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....
Availability: Used / Wrecking Yard Item
Item #: 32979 -
Single 390GT cylinder head for a 1968 S code 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. These are the GT exhaust manifolds with 14 drilled and tapped exhaust bolt holes. This cylinder head has 4 drilled and tapped, thermactor...
Availability: Used / Wrecking Yard Item
Item #: 33013 -
Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. These cylinder heads are factory drilled and tapped for thermactos smog tubes. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust...
Availability: Out of Stock
Item #: 33014 -
Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped holes for exhaust manifolds. These weigh 48 lbs. each, and cannot be combined with other items...
Availability: In-Stock Item
Item #: 30894 -
Three piece Thermactor Smog hose set; moulded, striped, and stamped like original factory installed hoses. The 1968 ink stamped was likely used partially into 1969. We also list hoses with the C9... stamps.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US1968 / 1969 428 Cobra Jet engines. 1968 / 1969 428 Super Cobra Jet engines. ...
Availability: In-Stock Item
Item #: 30895 -
Thermactor smog tube installation ferrules. Set of 8 nuts and barrel shaped ferrules.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US. 1968 / 1969 / 1970 428 Cobra Jet engines.1968 / 1969 / 1970 428 Super Cobra Jet engines. ...
Availability: Used / Wrecking Yard Item
Item #: 30409 -
Used oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.
Availability: In-Stock Item
Item #: 31629 -
Reproduction oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.
Availability: Used / Wrecking Yard Item
Item #: 31118 -
Used power steering oil cooler for many 1971-73 Ford, Lincoln and Mercury cars with air conditioning. Specifically these came from 1971-73 Mercury Cougar or Ford Mustangs with factory installed air conditioning and power steering. This unit mounts to the top of the A/C compressor. This installs inline with the low pressure return hose. Manufactured by the Blissfield Company and has a Ford stamped number of D1AA-3D746-AB. The Ford engineering number is D1AZ-3D746-D.
Featured!
Availability: In-Stock Item
Item #: 10575 -
Another spot-on reproduction by WCCC! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C9ZZ-8600-C. This fan will...
Featured!
Availability: In-Stock Item
Item #: 10574 -
Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C8OZ-8600-A. This fan will also work on many small block applications. We hope...
Availability: Used / Wrecking Yard Item
Item #: 33437 -
C7AE-D, Fan description - 5 blades and 18 inches in diameter. Ford master part number C7AE-8600-D. These 5 blade flex fans usually came on full sized Ford and Mercury cars starting in 1967. Can be used on any engine with the proper spacer with fan shroud with adequate fan opening. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...
Availability: Used / Wrecking Yard Item
Item #: 24502 -
Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.
Availability: Used / Wrecking Yard Item
Item #: 24395 -
Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.
Availability: In-Stock Item
Item #: 12136 -
Quality reproduction of the 1968 - 1970 CJ Mercury Cougar, 1969 - 1970 Shelby GT500, 1968 - 1969 Cyclone, Ford Fairlane, Ranchero and Torino 428 Cobra Jet Ram Air cleaner base. Features correct snorkel opening and breather elbow.Replaces Ford part number C9ZZ-9600-E or C8ZZ-9600-A.
Availability: Out of Stock
Item #: 10537 -
Black plastic elbow that clips onto the air cleaner base of most 1971-73 Mercury Cougar and most other Ford, Mercury, and Lincoln cars with V8 engines. Elbow for hose from PCV valve to stock air cleaner bases.
Availability: Used / Wrecking Yard Item
Item #: 25279 -
Original retainer that clips onto the breather element nipple sticking through the air cleaner base and holds the elbow for the hose going to the PCV valve. Ford calls this part the Crankcase Emissions Filter Retainer.The Master Parts Catalog says this part is only for 1971 and newer cars, but this part has been found on low mile 1970 cars as well. Ford part # D1AZ-9E628-A.
Availability: Out of Stock
Item #: 24993 -
Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.
Availability: Used / Wrecking Yard Item
Item #: 24338 -
Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.
Availability: Used / Wrecking Yard Item
Item #: 24339 -
Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.
Availability: In-Stock Item
Item #: 53256 -
Fan shroud hardware kit for the 302 or 351 on the 1971, 1972 or 1973 Cougar and Mustang.
Availability: In-Stock Item
Item #: 10631 -
New water pump gasket for 1971 Mercury Cougar and Ford Mustang with 429 Cobra Jet engines. Single gasket, seals engine to water pump plate only. Also fits the 360 engine. Will also fit Torino, Comet and Cyclone.
Availability: Used / Wrecking Yard Item
Item #: 32671 -
Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...
Availability: Used / Wrecking Yard Item
Item #: 32935 -
Dated 4G20, July 20, 1964.Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump...
Availability: Used / Wrecking Yard Item
Item #: 32934 -
Dated 6A13, January 13, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 6A13 or January 13, 1966. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water...
Availability: Used / Wrecking Yard Item
Item #: 33540 -
Dated 5F7 June 7, 1965. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5F7 or June 7, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings...
Availability: Used / Wrecking Yard Item
Item #: 12557 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Long block, factory H code 351-2V V-8 engine. 351 Cleveland engine rated at 177 Hp (net) with 8.6:1 compression ratio in 1971. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories, pulleys, and flex plate. Intake manifold...
Availability: Used / Wrecking Yard Item
Item #: 31515 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 6K19 or October 19, 1966. C6AE-6015-G. This item...
Availability: Used / Wrecking Yard Item
Item #: 31514 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 8D15 or April 15, 1968. This item cannot ship through any...
Availability: Used / Wrecking Yard Item
Item #: 32961 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7M27, December 27, 1967. Used 0.030 over bore 4.080" Ford 390 engine block. Years ago, it looks to have been fresh machined, with new freeze plugs. No paperwork, bare block. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date...
Availability: Used / Wrecking Yard Item
Item #: 32988 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 6F20, June 20, 1966. Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. This item cannot ship...
Availability: Used / Wrecking Yard Item
Item #: 33572 -
NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 8D2 or April 2 1968. This item cannot ship through any conventional...
Availability: In-Stock Item
Item #: 10619 -
Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.
Availability: Used / Wrecking Yard Item
Item #: 30136 -
Used distributor clamp and bolt, for any FE Engine: i.e. 352 / 360 / 390 / 410 / 427-4V / 428 / 428CJ / 428SCJ built from 1958-1976. Bolt may be used, or new from AMK Products. Ford part number B8A-12270-A.
Availability: Used / Wrecking Yard Item
Item #: 30135 -
Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.
Availability: Rare / NOS Part
Item #: 32883 -
New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.
Availability: Rare / NOS Part
Item #: 33325 -
New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.
Availability: In-Stock Item
Item #: 33586 -
Reproduction upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428. * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Replaces Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...
Availability: In-Stock Item
Item #: 33587 -
Reproduction upper distributor bushing for 1969-73 351W, 351C, 429, and 460 Ford V-8 engines. * Note - 260/ 289 / 302 / 352 / 390 / 410 / 427 / 428 engines, all used a different upper bushing. See related items for that listing. Replaces Ford part number C5AZ-12120-A. We measure 0. O.D., 0." I.D., and 1.750 long.
Availability: Used / Wrecking Yard Item
Item #: 27541 -
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Availability: Out of Stock
Item #: 31846 -
Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.
Availability: Rare / NOS Part
Item #: 33327 -
New Old Stock upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428. * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...
Availability: In-Stock Item
Item #: 10128 -
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.
Availability: In-Stock Item
Item #: 53276 -
Set of 20 bolts for the intake manifold on any 1970-71 Ford 429 Cobra Jet engine. 429CJ engines were optional in only in 1971 on Mercury Cougar and Ford Mustangs. Available in 1970 on B body Torino, Cyclone, Ranchero, Fairlane. *Note - Excludes Boss 429 engines.
Availability: Used / Wrecking Yard Item
Item #: 22234 -
Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.
Availability: Used / Wrecking Yard Item
Item #: 22235 -
Used cast iron choke stove from any 1970 351C-4V Ford engine. This is held on with 2 bolts. Casting number on the iron plate is D0AE-9A705-C, which is only for the plate. The plate and tube assembly has a Ford part number of D0AZ-9C869-A. No hardware included. Limited to stock on hand.* Note - for those who do not need the choke stove, a cast aluminum block off plate can be purchased through Summit.
Availability: In-Stock Item
Item #: 12488 -
Set of 16 bolts for the intake manifold on any factory 1969-70 Ford 351W-2V and 351W-4V engine. AMK F-1131.*Note - Excludes all 351 Cleveland engines.
Availability: In-Stock Item
Item #: 11273 -
Set of 12 bolts / spacers / stud for the intake manifold on any factory 1969-70 Ford S code 390-4V or 428 Cobra Jet or 428SCJ engine. AMK F-475.*Note - Excludes 1967-68 390 engines.
Availability: In-Stock Item
Item #: 25908 -
Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-2V engine. AMK F-1313.*Note - Excludes 351C-4V and 351W engines.
Availability: In-Stock Item
Item #: 32380 -
New gaskets for installing your 429 Cobra Jet intake manifold. This is the Felpro branded gasket. Fits 1970-71 Ford 429CJ engines. 1971 Mercury Cougar and Ford Mustang with J or C code 429CJ engines. Intake to cylinder head gaskets and intake end pieces, along with O ring for distributor. *Note - Excludes N code 429-4V or Thunderjet, passenger car engines.
Availability: Used / Wrecking Yard Item
Item #: 32983 -
C3AE-9425-B Cast iron intake manifold used on all 1963 390-4V engines in a Mercury or Ford. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C3AE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Fits FE engines, this could have come from a Galaxie or Thunderbird or full sized Mercury. Probably also 352 engines. Current date available: 2M29. December 29, 1962. *Trivia - One of the heaviest car...
Availability: In-Stock Item
Item #: 41411 -
Set of 12 bolts for the intake manifold on any factory 1966-67 Ford 289 engine. AMK F-478.*Note - Excludes 1968 289 and 302 engines.
Availability: In-Stock Item
Item #: 25913 -
Set of (12) 2 1/16" bolts / studs and nuts for the intake manifold on any factory 1968 Ford 289 or 302 engine. AMK F-479. *Note - Excludes 1967 289 engines.
Availability: In-Stock Item
Item #: 11996 -
Set of 10 bolts and several spacers for the intake manifold on any factory 1967 Ford S or Z code, 390 engine. AMK F-475.*Note - Excludes 1968 1969 1970 - 390 and 428CJ engines.
Availability: In-Stock Item
Item #: 80222 -
Set of bolts and studs for the intake manifold on any 1970 Ford 428 Cobra Jet engine. The 1970 set includes a second double ended stud, while the 1969 set only includes 1 double stud. 1970 R and Q code Mustang and Cougar.Trivia - 1970 Mercury Cougars only have a Q as the 5th digit in the VIN code. Yes, All 1970 428 cobra jet Cougars are designated as Q codes. Ram air was optional and will show on the window sticker or Marti Report.
Availability: In-Stock Item
Item #: 14281 -
Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-4V engine. AMK F-1321.*Note - Excludes 351C-2V and 351W engines.
Availability: Used / Wrecking Yard Item
Item #: 31810 -
NOTE* After comparing to the original pulley, we've found that this reproduction is approximately 3/16" shorter in overall height. New crank shaft pulley, single sheave small block Ford 289 / 302 351W engines up to 1969. Single V-belt or fan belt pulley, means for use with only the alternator. Not for use with power steering, air conditioning, or smog pump. Measures just under 6-1/4 inches in diameter. Single sheave crank shaft pulley with 3 bolt holes, excludes engines after 1970....
Availability: Used / Wrecking Yard Item
Item #: 12463 -
Used crank shaft pulley for any 1969 Mercury Cougar or Ford Mustang with 351w engine. This is a single groove pulley with a 6-1/8 inch diameter, and would have been used without power steering. One belt just for the water pump and alternator. Also fits other cars with 351 Windsor engines without P/S.Replaces Ford part number C9OE-6A312-D.
Availability: In-Stock Item
Item #: 13913 -
Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet. Replaces Ford part # C9AZ-2167-B.
Availability: Used / Wrecking Yard Item
Item #: 13676 -
Used vacuum tree for any 1970 Mercury Cougar, Ford Mustang, or 1970-71 Ford Torino. This manifold assembly mounts to the firewall in the engine compartment, and is unique to the above applications, as it has 6 different vacuum outlets or sources. These connect to the brake booster, heater / air conditioning vacuum parts, and other accessory items that use vacuum. Replaces Ford part number D0OZ-9C490-A or D0OA-9C490-A.
Availability: In-Stock Item
Item #: 18736 -
Set of 6 bolts for installing an OEM Ford timing cover marked C5OE-6059-A, which originally came on all 1967 Mercury Cougars with 289 engines or 1965-67 Fords including Mustang with 289 engines. 5 short and 1 long bolt in this kit.
Availability: In-Stock Item
Item #: 18872 -
Set of 6 bolts for installing an OEM Ford timing cover marked C8AE-6059-A, which originally came on all 1969-70 Mercury Cougars with 289 / 302/ 351W engines or 1968-70 Fords including Mustang with 289 / 302/ 351W engines. 4 short and 2 long bolt in this kit.*Note this kit is not applicable to the early designed Ford timing cover, see related items for other kit.
Availability: In-Stock Item
Item #: 21617 -
Set of 10 bolts for installing an OEM Ford timing cover marked C3AE-6059-A, which originally came on all 1967 Mercury Cougars with 390 engines or 1963-67 Fords including Mustang with 352 / 390 / 410 / 428 engines. 10 total new bolts.*Note - this kit is not applicable to the 1968 and later Ford FE timing covers. See related items for other kit.
Availability: In-Stock Item
Item #: 22224 -
Set of 10 bolts for installing an OEM Ford timing cover marked C8AE-6059-B, which originally came on all 1968-70 Mercury Cougars with 390 / 428CJ / 427-4V engines or 1968-70 Fords including Mustang with 352 / 390 / 428CJ engines. *Note this kit is not applicable to the 1963-67 designed Ford FE timing cover, see related items for other kit.
Availability: In-Stock Item
Item #: 20668 -
Set of 3 bolts for installing an OEM Ford timing cover, which originally came on all 1970-73 Mercury Cougars with 351C or Cleveland engines or 1970-74 Fords including Mustang with 351 Cleveland engines. Also fits 351M and 400M Ford engines*Note - this kit is not applicable to the 351W or Windsor engine. See related items for other kit.
Availability: Used / Wrecking Yard Item
Item #: 31181 -
Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.
Availability: In-Stock Item
Item #: 31055 -
Oil pan bolt kit for all FE 390, 427, and 428 engines. Set is made by AMK and includes 20 OEM style bolts and washers. We sell them specifically for 1967-70 Mercury Cougar and Ford Mustang, but they will fit most all Ford "FE" engines including 352, 410, and 360 Ford engines. If you happen to have a 428CJ with windage tray, we also offer a set of bolts for that application too. ...
Availability: In-Stock Item
Item #: 31056 -
Oil pan bolt kit for all 428 Cobra Jet and 428 Super Cobra Jet engines with windage tray. Set is made by AMK and includes 20 OEM style bolts and washers.
Availability: Used / Wrecking Yard Item
Item #: 33550 -
Used oil screen pick up tube assembly from a small block Ford 351W or Windsor engine. This is for most front sump 351W engines in Ford cars from 1969 to at least 1971. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. * Excludes 289/302 and 351C engines, and all F...